Built-in iSight webcams have an interrupt endpoint but spit proprietary data
that don't conform to the UVC status endpoint messages. Don't try to handle
the interrupt endpoint for those cameras.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When the first bulk URB of a video payload contains an erroneous header, or
when no V4L2 buffer is available, the whole payload must be dropped. Change
the skip logic to drop all bulk URBs until the end of the payload instead of
the first one only.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This camera is rather similar to MT9M001, but also has a couple of
enhanced features, like pixel binning.

 create mode 100644 drivers/media/video/mt9t031.c
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Don't modify driver's state in try_fmt, just verify format acceptability
or adjust it to driver's capabilities.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

priv->scale is checked in start_capture.
Therefore, it should be NULL if failing in set_fmt.
This patch resolve this problem.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds tw9910 driver that use soc_camera framework.
It was tested on SH Migo-r board and mplayer.

 create mode 100644 drivers/media/video/tw9910.c
 create mode 100644 include/media/tw9910.h
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In preparation for i.MX31 camera host driver add flags for 4 and 15 bit bus
widths and for data lines polarity inversion.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

sh_mobile_ceu_camera.c is already prepared to support interlaced format, this
patch moves the choice of a field type down to host and / or camera drivers.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch cleans up the sh_mobile_ceu driver and adds comments and
constants to clarify the magic sequence in sh_mobile_ceu_capture().
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch presents new method to be able to select V4L2 input type
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch presents new method to be able to check v4l2_std_id
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds NV16/NV61 support to the sh_mobile_ceu driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds NV12/NV21 support to the sh_mobile_ceu driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Move mutex from host drivers to camera device object, take into account
videobuf locking.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With the introduction of the format conversion support in soc-camera, we now
also have to take care to pass the correct pixel format to the camera driver
when calling its try_fmt() method.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Simplify multiple drivers by replacing f->fmt.pix.* with a single pointer
dereference, merge some needlessly broken lines, verify host and camera
operations pointers on registration.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch converts the sh_mobile_ceu driver to make use
of the new pixel format translation code. Only pass-though
mode at this point.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for NV16 and NV61 pixel formats.

These pixel formats use two planes; one for 8-bit Y values and
one for interleaved 8-bit U and V values. NV16/NV61 formats are
very similar to NV12/NV21 with the exception that NV16/NV61 are
using the same number of lines for both planes. The difference
between NV16 and NV61 is the U and V byte order.

The fourcc values are extrapolated from the NV12/NV21 case.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The chip is largely compatible with MT9M111 and is going to be supported by the
same driver.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Using PXA270's FIFO inactivity time-out register (CITOR) reduces FIFO overruns.
The time-out is calculated in CICLK / LCDCLK ticks and has to be longer than
one pixel time. For this we have to know the pixel clock frequency, which
usually is provided by the camera. We use the struct soc_camera_sense to
request PCLK frequency from the camera driver upon each data format change.
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a struct soc_camera_sense, that can be used by camera host drivers to
request additional information from a camera driver, for example, when
changing data format. This struct can be extended in the future, its first use
is to request the camera driver whether the pixel-clock frequency has changed.
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As reported by Antonio Ospite <ospite@studenti.unina.it> two platforms with a
mt9m111 camera require opposite pixel clock polarity, which means one of them
inverts it. This patch adds support for inversion flags and switches all
available camera drivers to using them.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

"static" on stv06xx for all static functions and parameters to avoid
such troubles.

Cc: Erik Andren <erik.andren@gmail.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Testing for non-NULL platform-data is not enough, we have to check if the GPIO
in the platform data is valid or not. Also see my earlier patch:

	[ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Micron mt9m111 offers 4 byte orders for YCbCr
output. This patchs adds all possible outputs capabilities
to the mt9m111 driver.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

unsigned >= 0 is always true and fix formula
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Patch replace return -1; with return retval; in 3 functions.
And we also change if-checks for this returned values.
Signed-off-by: NAlexey Klimov <klimov.linux@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Due to a lot of patches for dsbr100 last time we should update version
of driver.
Signed-off-by: NAlexey Klimov <klimov.linux@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>