Currently still with an empty register state, this will follow in a
next step. This one here just creates the new vfunc and uses it for
cross-checking, initial state takeover and the dpll assert function.

And add a FIXME for the ddi pll readout code, which still needs to be
converted over.

v2:
- Add some hw state readout debug output.
- Also cross check the enabled crtc counting.

Note that I've botched up the patch ordering, and before this patch
we've read out the pll selection correctly, but did not reconstruct
the refcounts properly. See the bug link.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65673Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So don't try to store it in the DPLL_FP register.

Otherwise it looks like the limits for pineview are correct: It has
it's own clock computation code, which doesn't use an offset for n
divisors, and the register value based m limits look sane enough.

v2: Rebase on top of the pineview clock refactor and fixup up the
commit message: It's m1 pnv doens't care about, not m2!

Quoting Damien's review:

  - "n can vary between 2 and 6, but we declare the 3-6 as limits.
  - "p1 seems to be able to go up to 9
  - "the m upper limit seems a bit big, but the docs are a bit shy on
    that values for pnv.

"Otherwise, the change itself seems good:"
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We don't (yet) have proper pixel multiplier readout support on pch
split platforms, so the cross check will naturally fail.

v2: Fix spelling in the comment, spotted by Ville.

v3: Since the ordering constraint is pretty tricky between the crtc
get_pipe_config callback and the encoder->get_config callback add a
few comments about it. Prompted by a discussion with Chris Wilson on
irc about why this does work anywhere else than on i915g/gm.
Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Stéphane Marchesin found a bug where the fences were not being restored,
and in particular the fence pin_count was incorrect. Had we had a
warning in place, this bug would have come to light much earlier. Better
late than never?
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is of no value to the developer reading the report, let alone the
bamboozled user.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we detect a ring is in a valid wait for another, just let it be.
Eventually it will either begin to progress again, or the entire system
will come grinding to a halt and then hangcheck will fire as soon as the
deadlock is detected.

This error was foretold by Ben in
commit 05407ff8
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date:   Thu May 30 09:04:29 2013 +0300

    drm/i915: detect hang using per ring hangcheck_score

"If ring B is waiting on ring A via semaphore, and ring A is making
progress, albeit slowly - the hangcheck will fire. The check will
determine that A is moving, however ring B will appear hung because
the ACTHD doesn't move. I honestly can't say if that's actually a
realistic problem to hit it probably implies the timeout value is too
low."

v2: Make sure we don't even incur the KICK cost whilst waiting.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65394Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After kicking a ring, it should be free to make progress again and so
should not be accused of being stuck until hangcheck fires once more. In
order to catch a denial-of-service within a batch or across multiple
batches, we still do increment the hangcheck score - just not as
severely so that it takes multiple kicks to fail.

This should address part of Ben's justified criticism of

commit 05407ff8
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date:   Thu May 30 09:04:29 2013 +0300

    drm/i915: detect hang using per ring hangcheck_score

"There's also another corner case on the kick. If the seqno = 2
(though not stuck), and on the 3rd hangcheck, the ring is stuck, and
we try to kick it... we don't actually try to find out if the kick
helped."

v2: Make sure we catch DoS attempts with batches full of invalid WAITs.
v3: Preserve the ability to detect loops by always charging the ring
    if it is busy on the same request.
v4: Make sure we queue another check if on a new batch

References: https://bugs.freedesktop.org/show_bug.cgi?id=65394Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we reset and restart a ring, we also want to clear any existing
hangcheck.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In case of intel_sdvo_get_active_outputs() failing, we end up reading a
value from the stack.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's now intel_sdvo_get_capabilities().
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The hw state readout code for the pipe config will now check
this for us, so rip out this hand-rolled complexity.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Looks at first like a bit of overkill, but
- Haswell actually wants different enable/disable functions for
  different plls.
- And once we have full dpll hw state tracking we can move the full
  register setup into the ->enable hook.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Using ids in register macros is much more common in our driver. Also
this way we can reduce the platform specific stuff a bit.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

An id to match the idx (useful for register access macros) and a name
fore neater debug output.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the future this won't be just for pch plls, so move it into the
shared dpll init code.

v2: Bikeshed the uncessary {} away while applying to appease
checkpatch.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Well, the first step of a long road at least, it only reads out
the pipe -> shared dpll association thus far. Other state which needs
to follow:

- hw state of the dpll (on/off + dpll registers). Currently we just
  read that out from the hw state, but that doesn't work too well when
  the dpll is in use, but not yet fully enabled. We get away since
  most likely it already has been enabled and so the correct state is
  left behind in the registers. But that doesn't hold for atomic
  modesets when we want to enable all pipes at once.

- Refcount reconstruction for each dpll.

- Cross-checking of all the above. For that we need to keep the dpll
  register state both in the pipe and in the shared_dpll struct, so
  that we can check that every pipe is still connected to a correctly
  configured dpll.

Note that since the refcount resconstruction isn't done yet this will
spill a few WARNs at boot-up while trying to disable pch plls which
have bogus refcounts. But since there's still a pile of refactoring to
do I'd like to lock down the state handling as soon as possible hence
decided against reordering the patches to quiet these WARNs - after
all the issues they're complaining about have existed since forever,
as Jesse can testify by having pch pll states blow up consistently in
his fastboot patches ...

v2: We need to preserve the old shared_dpll since currently the
shared dpll refcount dropping/getting is done in ->mode_set. With
the usual pipe_config infrastructure the old dpll id is already lost
at that point, hence preserve it in the new config.

v3: Rebase on top of the ips patch from Paulo.

v4: We need to unconditionally take over the shared_dpll id from the
old pipe config when e.g. doing a direct pch port -> cpu edp
transition.

v5: Move the saving of the old shared_dpll id to an ealier patch.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The bits are evenly space, so we can cut down on two big switch
blocks. This also greatly simplifies the hw state readout which
follows in the next patch.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the big sed-job prep work done this is now really simple. With
the exception that we only assign the right shared dpll id in the
->mode_set callback but also depend upon the old one still being
around.

Until that mess is fixed up we need to jump through a few hoops to
keep the old value save.

v2: Kill the funny whitespace spotted by Chris.

v3: Move the shared_dpll pipe config fixup into this patch as noticed
by Ville. Also unconditionally set the shared_dpll with the current
one, since otherwise we won't handle direct pch port -> cpu edp
transitions correctly.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Dealing with discrete enum values is simpler for hw state readout and
pipe config computations than pointers - having neat names instead of
chasing pointers should look better in the code.

This isn't a that good reason for pch plls, but on haswell we actually
have 3 different types of plls: WRPLL, SPLL and the DP clocks. Having
explicit names should help there.

Since this also adds the intel_crtc_to_shared_dpll helper to further
abstract away the crtc -> dpll relationship this will also help to
make the next patch simpler, which moves the shared dpll into the pipe
configuration.

Also note that for uniformity we have two special dpll ids: NONE for
pipes which need a shared pll but don't have one (yet) and private for
when there's a non-shared pll (e.g. per-pipe or per-port pll).

I've thought whether we should also add a 2nd enum for the type of the
pll we want (for really generic pll selection code) but thrown that
idea out again - likely there's too much platform craziness going on
to be able to share the pll selection logic much.

Since this touched all the shared_pll functions a bit I've also done
an s/intel_crtc/crtc/ replacement on a few of them.

v2: Kill DPLL_ID_NONE. It's probably better to call it DPLL_ID_INVALID and use
it to check that the compute config stage assigns a dpll to every pipe.
But since that code isn't ready yet until we move the dpll selection out
of the ->mode_set callback, there's no use for it.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For fastboot we need some support to read out the sharing state of
plls, at least for platforms where they can be shared (or freely
assigned at least). Now for ivb we already have pretty extensive
infrastructure for tracking pch plls, and it took us an aweful lot of
tries to get that remotely right. Note that hsw could also share plls,
but even now they're already freely assignable. So we need this on
more than just ivb.

So on top of the usual fastboot fun pll sharing seems to be an
additional step up in fragility. Hence a common infrastructure for all
shared/freely assignable display plls seems to be in order.

The plan is to have a bit of dpll hw state readout code, which can be
used individually, but also to fill in the pipe config. The hw state
cross check code will then use that information to make sure that
after every modeset every pipe still is connected to a pll which still
has the correct configuration - a lot of the pch pll sharing bugs
where due to incorrect sharing.

We start this endeavour with a simple s/pch_pll/shared_dpll/ rename
job.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Before I start to make a complete mess out of this, crank up
the paranoia level a bit.

v2: Kill the has_pch_encoder check in put_shared_dpll - it's invalid
as spotted by Ville since we currently only put the dpll when we
already have the new pipe config. So a direct pch port -> cpu edp
transition will hit this.

v3: Now that I've lifted my blinders add the WARN_ON Ville requested.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Simlar to how disable already works on haswell. This is possible
since we now carefully track the pch state in the pipe config.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We ->mode_set is called we can't just blindly reuse an existing pll
since that might be shared with a different, still active pch output.

v2: Only update the pll settings when the pch pll is know to be
unused, otherwise we can wreak havoc with a running pipe. Which in the
case of DP will likely result in a black screen due to loss of link
lock.

v3: Tighten up the asserts a bit more, especially make sure that the
pch pll is still enabled when we try to disable it. This would have
caught the bug fixed in this patch.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This makes, arguably, the condition on state easier to read.
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The hotplug_mask is no longer used as the hpd interrupt setup is now
handled in the core.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Don't enable the cursor until g4x_fixup_plane() had a chance to do
cast its magic spell.

Egbert writes:
"Today I had the chance to test this. First I tried
 if I can still reproduce the blank with this patch
 added when I disable my voodoo g4x_fixup_plane():
 It turned out it still happens however very rarely
 (like 1 out of 20 tries). When I reenabled my voodoo
 the issue still occurred.
 I had to switch two lines around, ie:

         intel_enable_plane(dev_priv, plane, pipe);
         if (IS_G4X(dev))
                 g4x_fixup_plane(dev_priv, pipe);
 +       intel_crtc_update_cursor(crtc, true);

 to avoid the blank screen issue - which is it didn't
 happen in ~75 tries."

v2: Add a comment to remind people of the ordering constraints
Acked-by: NEgbert Eich <eich@suse.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

WaFbcNukeOn3DBlt for IVB, HSW.

According BSPec: "Workaround: Do not enable Render Command Streamer tracking for FBC.
Instead insert a LRI to address 0x50380 with data 0x00000004 after the PIPE_CONTROL that
follows each render submission."

v2: Chris noticed that flush_domains check was missing here and also suggested to do
    LRI only when fbc is enabled. To avoid do a I915_READ on every flush lets use the
    module parameter check.

v3: Adding Wa name as Damien suggested.

v4: Ville noticed VLV doesn't support fbc at all and comment came wrong from spec.

v5: Ville noticed than on blt a Cache Clean LRI should be used instead the Nuke one.

v6: Check for flush domain on blt (by Ville).
    Check for scanout dirty (by Chris).

v7: Apply proper fbc_dirty implemented by Chris.

v8: remove unused variables.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is required for tracking render damage for use with FBC and will be
used in subsequent patches.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Pull the code to disable trickle feed for all primary planes into a
separate function.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We disable trickle feed in all the (relevant) clock gating functions,
except ironlake_init_clock_gating(). Copy paste the same code there as
well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to BSpec, trickle feed should be disabled for BW and
mobile CL. Those constraints seem to match all of our gen4 chipsets.

Trickle feed is disabled via the MI_ARB_STATE register instead of
per plane controls on gen4.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The docs say that the trickle feed disable bit is present (for primary
planes only, not video sprites) on CTG, and that it must be set
for ELK. Just set it for all g4x chipsets.

v2: Do it in init_clock_gating too
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We always limited the link bw calculations to 24bpp. Tested with
my shiny new high-bpc screen, seems to work as advertised.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65280Tested-by: Nshui yangwei <yangweix.shui@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For various reasons the hw state readout might not be able to
faithfully match the hw state:
- broken hw (like the case which motivated this patch here where the
  sdvo encoder does not implemented mandatory functionality
  correctly).
- platforms which are not supported fully with the pipe config
  infrastructure
- if our code doesn't support a given hw configuration natively, e.g.
  special restrictions on the per-pipe panel fitters when they're used
  in high-quality scaling modes.

In all these cases both fastboot and the hw state cross checker need
to be aware of these cases and act accordingly. To be able to do this
add a new quirk flag to the pipe config structure.

The specific case at hand is an sdvo encoder which doesn't implement
the get_timings function, so adjusted_mode flags will be wrong. The
strange thing though is that the encoder _does_ work, even though it
doesn't implement any of the timings functions (so neither get nor
set, neither for input nor output timings).

Not that non-compliant sdvo encoder are any surprise at all ...

v2:
- Don't read random garbage from the dtd if the get_timings call
  failed (suggested by Chris).
- Still check the interlaced flag, that's read out from someplace
  else. We want maximal paranoia, after all.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Haswell Display audio depends on power well in graphic side, it should
request power well before use it and release power well after use.
I915 will not shutdown power well if it detects audio is using.
This patch protects display audio crash for Intel Haswell C3 stepping board.
Signed-off-by: NWang Xingchao <xingchao.wang@linux.intel.com>
Reviewed-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For Intel Haswell chip, HDA controller and codec have
power well dependency from GPU side. This patch added support
to request/release power well in audio driver. Power save
feature should be enabled to get runtime power saving.

There's deadlock when request_module(i915) in azx_probe.
It looks like:
device_lock(audio pci device) -> azx_probe -> module_request
(or symbol_request) -> modprobe (userspace) -> i915 init ->
drm_pci_init -> pci_register_driver -> bus_add_driver -> driver_attach ->
which in turn tries all locks on pci bus, and when it tries the one on the
audio device, it will deadlock.

This patch introduce a work to store remaining probe stuff, and let
request_module run in safe work context.
Signed-off-by: NWang Xingchao <xingchao.wang@linux.intel.com>
Reviewed-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NLiam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is a preliminary work for the upcoming Haswell HDMI audio fixes.

azx_first_init() function can be safely called after the f/w loader,
since the f/w loader doesn't require the sound hardware initialization
beforehand.  Moving it into azx_probe_continue() cleans up the code
flow a bit.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The device can support runtime PM no matter whether it support
signal wakeup or not. For some chips like Haswell which doesnot
support PME by default, this patch let haswell Display HD-A controller
enter runtime suspend, and bring more power saving whith power-well
feature enabled.
Signed-off-by: NWang Xingchao <xingchao.wang@linux.intel.com>
Reviewed-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CTG/ILK/SNB/IVB support 4kx2k surfaces. HSW supports 4kx4k, but
without proper front buffer invalidation on the last 2k lines, so
don't enable FBC on these cases for now.

v2: Use gen >= 5, not gen > 4 (Daniel).
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Incomplete since ilk+ support needs proper pch dpll tracking first.
SDVO get_config parts based on a patch from Jesse Barnes, but fixed up
to actually work.

v2: Make sure that we call encoder->get_config _after_ we
get_pipe_config to be consistent in both setup_hw_state and the
modeset state checker. Otherwise the clever trick with handling the
pixel mutliplier on i915G/GM where the encoder overrides the default
value of 1 from the crtc get_pipe_config function doesn't work.
Spotted by Imre Deak.

v3: Actually cross-check the pixel mutliplier (but not on pch split
platforms for now). Now actually also tested on a i915G with a sdvo
encoder plugged in.

Cc: Imre Deak <imre.deak@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>