Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 22 11月, 2019 2 次提交
    • A
      nvme: hwmon: provide temperature min and max values for each sensor · 52deba0f
      由 Akinobu Mita 提交于 
      According to the NVMe specification, the over temperature threshold and
under temperature threshold features shall be implemented for Composite
Temperature if a non-zero WCTEMP field value is reported in the Identify
Controller data structure.  The features are also implemented for all
implemented temperature sensors (i.e., all Temperature Sensor fields that
report a non-zero value).

This provides the over temperature threshold and under temperature
threshold for each sensor as temperature min and max values of hwmon
sysfs attributes.

The WCTEMP is already provided as a temperature max value for Composite
Temperature, but this change isn't incompatible.  Because the default
value of the over temperature threshold for Composite Temperature is
the WCTEMP.

Now the alarm attribute for Composite Temperature indicates one of the
temperature is outside of a temperature threshold.  Because there is only
a single bit in Critical Warning field that indicates a temperature is
outside of a threshold.

Example output from the "sensors" command:

nvme-pci-0100
Adapter: PCI adapter
Composite:    +33.9°C  (low  = -273.1°C, high = +69.8°C)
                       (crit = +79.8°C)
Sensor 1:     +34.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 2:     +31.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 5:     +47.9°C  (low  = -273.1°C, high = +65261.8°C)

This also adds helper macros for kelvin from/to milli Celsius conversion,
and replaces the repeated code in hwmon.c.

Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Jean Delvare <jdelvare@suse.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NKeith Busch <kbusch@kernel.org>
      52deba0f
    • C
      nvmet: add another maintainer · 3aeb6a24
      由 Christoph Hellwig 提交于 
      Sagi and I have been pretty busy lately, and Chaitanya has been
helping a lot with target work and agreed to share the load.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NKeith Busch <kbusch@kernel.org>
      3aeb6a24
  3. 13 11月, 2019 1 次提交
  5. 12 11月, 2019 1 次提交
    • G
      nvme: Add hardware monitoring support · 400b6a7b
      由 Guenter Roeck 提交于 
      nvme devices report temperature information in the controller information
(for limits) and in the smart log. Currently, the only means to retrieve
this information is the nvme command line interface, which requires
super-user privileges.

At the same time, it would be desirable to be able to use NVMe temperature
information for thermal control.

This patch adds support to read NVMe temperatures from the kernel using the
hwmon API and adds temperature zones for NVMe drives. The thermal subsystem
can use this information to set thermal policies, and userspace can access
it using libsensors and/or the "sensors" command.

Example output from the "sensors" command:

nvme0-pci-0100
Adapter: PCI adapter
Composite:    +39.0°C  (high = +85.0°C, crit = +85.0°C)
Sensor 1:     +39.0°C
Sensor 2:     +41.0°C
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NKeith Busch <kbusch@kernel.org>
      400b6a7b
  7. 05 11月, 2019 27 次提交
  9. 01 11月, 2019 1 次提交
    • D
      loop: fix no-unmap write-zeroes request behavior · efcfec57
      由 Darrick J. Wong 提交于 
      Currently, if the loop device receives a WRITE_ZEROES request, it asks
the underlying filesystem to punch out the range.  This behavior is
correct if unmapping is allowed.  However, a NOUNMAP request means that
the caller doesn't want us to free the storage backing the range, so
punching out the range is incorrect behavior.

To satisfy a NOUNMAP | WRITE_ZEROES request, loop should ask the
underlying filesystem to FALLOC_FL_ZERO_RANGE, which is (according to
the fallocate documentation) required to ensure that the entire range is
backed by real storage, which suffices for our purposes.

Fixes: 19372e27 ("loop: implement REQ_OP_WRITE_ZEROES")
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
      efcfec57
  11. 26 10月, 2019 1 次提交
  13. 25 10月, 2019 5 次提交
    • J
      Merge branch 'md-next' of... · 9c6694bd
      由 Jens Axboe 提交于 
      Merge branch 'md-next' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md into for-5.5/drivers

Pull MD changes from Song.

* 'md-next' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
  md: no longer compare spare disk superblock events in super_load
  md: improve handling of bio with REQ_PREFLUSH in md_flush_request()
  md/bitmap: avoid race window between md_bitmap_resize and bitmap_file_clear_bit
  md/raid0: Fix an error message in raid0_make_request()
      9c6694bd
    • Y
      md: no longer compare spare disk superblock events in super_load · 6a5cb53a
      由 Yufen Yu 提交于 
      We have a test case as follow:

  mdadm -CR /dev/md1 -l 1 -n 4 /dev/sd[a-d] \
	--assume-clean --bitmap=internal
  mdadm -S /dev/md1
  mdadm -A /dev/md1 /dev/sd[b-c] --run --force

  mdadm --zero /dev/sda
  mdadm /dev/md1 -a /dev/sda

  echo offline > /sys/block/sdc/device/state
  echo offline > /sys/block/sdb/device/state
  sleep 5
  mdadm -S /dev/md1

  echo running > /sys/block/sdb/device/state
  echo running > /sys/block/sdc/device/state
  mdadm -A /dev/md1 /dev/sd[a-c] --run --force

When we readd /dev/sda to the array, it started to do recovery.
After offline the other two disks in md1, the recovery have
been interrupted and superblock update info cannot be written
to the offline disks. While the spare disk (/dev/sda) can continue
to update superblock info.

After stopping the array and assemble it, we found the array
run fail, with the follow kernel message:

[  172.986064] md: kicking non-fresh sdb from array!
[  173.004210] md: kicking non-fresh sdc from array!
[  173.022383] md/raid1:md1: active with 0 out of 4 mirrors
[  173.022406] md1: failed to create bitmap (-5)
[  173.023466] md: md1 stopped.

Since both sdb and sdc have the value of 'sb->events' smaller than
that in sda, they have been kicked from the array. However, the only
remained disk sda is in 'spare' state before stop and it cannot be
added to conf->mirrors[] array. In the end, raid array assemble
and run fail.

In fact, we can use the older disk sdb or sdc to assemble the array.
That means we should not choose the 'spare' disk as the fresh disk in
analyze_sbs().

To fix the problem, we do not compare superblock events when it is
a spare disk, as same as validate_super.
Signed-off-by: NYufen Yu <yuyufen@huawei.com>
Signed-off-by: NSong Liu <songliubraving@fb.com>
      6a5cb53a
    • D
      md: improve handling of bio with REQ_PREFLUSH in md_flush_request() · 775d7831
      由 David Jeffery 提交于 
      If pers->make_request fails in md_flush_request(), the bio is lost. To
fix this, pass back a bool to indicate if the original make_request call
should continue to handle the I/O and instead of assuming the flush logic
will push it to completion.

Convert md_flush_request to return a bool and no longer calls the raid
driver's make_request function.  If the return is true, then the md flush
logic has or will complete the bio and the md make_request call is done.
If false, then the md make_request function needs to keep processing like
it is a normal bio. Let the original call to md_handle_request handle any
need to retry sending the bio to the raid driver's make_request function
should it be needed.

Also mark md_flush_request and the make_request function pointer as
__must_check to issue warnings should these critical return values be
ignored.

Fixes: 2bc13b83 ("md: batch flush requests.")
Cc: stable@vger.kernel.org # # v4.19+
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: NDavid Jeffery <djeffery@redhat.com>
Reviewed-by: NXiao Ni <xni@redhat.com>
Signed-off-by: NSong Liu <songliubraving@fb.com>
      775d7831
    • G
      md/bitmap: avoid race window between md_bitmap_resize and bitmap_file_clear_bit · fadcbd29
      由 Guoqing Jiang 提交于 
      We need to move "spin_lock_irq(&bitmap->counts.lock)" before unmap previous
storage, otherwise panic like belows could happen as follows.

[  902.353802] sdl: detected capacity change from 1077936128 to 3221225472
[  902.616948] general protection fault: 0000 [#1] SMP
[snip]
[  902.618588] CPU: 12 PID: 33698 Comm: md0_raid1 Tainted: G           O    4.14.144-1-pserver #4.14.144-1.1~deb10
[  902.618870] Hardware name: Supermicro SBA-7142G-T4/BHQGE, BIOS 3.00       10/24/2012
[  902.619120] task: ffff9ae1860fc600 task.stack: ffffb52e4c704000
[  902.619301] RIP: 0010:bitmap_file_clear_bit+0x90/0xd0 [md_mod]
[  902.619464] RSP: 0018:ffffb52e4c707d28 EFLAGS: 00010087
[  902.619626] RAX: ffe8008b0d061000 RBX: ffff9ad078c87300 RCX: 0000000000000000
[  902.619792] RDX: ffff9ad986341868 RSI: 0000000000000803 RDI: ffff9ad078c87300
[  902.619986] RBP: ffff9ad0ed7a8000 R08: 0000000000000000 R09: 0000000000000000
[  902.620154] R10: ffffb52e4c707ec0 R11: ffff9ad987d1ed44 R12: ffff9ad0ed7a8360
[  902.620320] R13: 0000000000000003 R14: 0000000000060000 R15: 0000000000000800
[  902.620487] FS:  0000000000000000(0000) GS:ffff9ad987d00000(0000) knlGS:0000000000000000
[  902.620738] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  902.620901] CR2: 000055ff12aecec0 CR3: 0000001005207000 CR4: 00000000000406e0
[  902.621068] Call Trace:
[  902.621256]  bitmap_daemon_work+0x2dd/0x360 [md_mod]
[  902.621429]  ? find_pers+0x70/0x70 [md_mod]
[  902.621597]  md_check_recovery+0x51/0x540 [md_mod]
[  902.621762]  raid1d+0x5c/0xeb0 [raid1]
[  902.621939]  ? try_to_del_timer_sync+0x4d/0x80
[  902.622102]  ? del_timer_sync+0x35/0x40
[  902.622265]  ? schedule_timeout+0x177/0x360
[  902.622453]  ? call_timer_fn+0x130/0x130
[  902.622623]  ? find_pers+0x70/0x70 [md_mod]
[  902.622794]  ? md_thread+0x94/0x150 [md_mod]
[  902.622959]  md_thread+0x94/0x150 [md_mod]
[  902.623121]  ? wait_woken+0x80/0x80
[  902.623280]  kthread+0x119/0x130
[  902.623437]  ? kthread_create_on_node+0x60/0x60
[  902.623600]  ret_from_fork+0x22/0x40
[  902.624225] RIP: bitmap_file_clear_bit+0x90/0xd0 [md_mod] RSP: ffffb52e4c707d28

Because mdadm was running on another cpu to do resize, so bitmap_resize was
called to replace bitmap as below shows.

PID: 38801  TASK: ffff9ad074a90e00  CPU: 0   COMMAND: "mdadm"
   [exception RIP: queued_spin_lock_slowpath+56]
   [snip]
-- <NMI exception stack> --
 #5 [ffffb52e60f17c58] queued_spin_lock_slowpath at ffffffff9c0b27b8
 #6 [ffffb52e60f17c58] bitmap_resize at ffffffffc0399877 [md_mod]
 #7 [ffffb52e60f17d30] raid1_resize at ffffffffc0285bf9 [raid1]
 #8 [ffffb52e60f17d50] update_size at ffffffffc038a31a [md_mod]
 #9 [ffffb52e60f17d70] md_ioctl at ffffffffc0395ca4 [md_mod]

And the procedure to keep resize bitmap safe is allocate new storage
space, then quiesce, copy bits, replace bitmap, and re-start.

However the daemon (bitmap_daemon_work) could happen even the array is
quiesced, which means when bitmap_file_clear_bit is triggered by raid1d,
then it thinks it should be fine to access store->filemap since
counts->lock is held, but resize could change the storage without the
protection of the lock.

Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: NGuoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: NSong Liu <songliubraving@fb.com>
      fadcbd29
    • D
      md/raid0: Fix an error message in raid0_make_request() · e3fc3f3d
      由 Dan Carpenter 提交于 
      The first argument to WARN() is supposed to be a condition.  The
original code will just print the mdname() instead of the full warning
message.

Fixes: c84a1372 ("md/raid0: avoid RAID0 data corruption due to layout confusion.")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSong Liu <songliubraving@fb.com>
      e3fc3f3d
  15. 18 10月, 2019 1 次提交
  17. 07 10月, 2019 1 次提交