Add ->chipset field to ide_pci_device_t and use it in ide_hwif_configure()
to set hwif->chipset.  Convert cmd64x, cy82c693, rz1000 and trm290 host
drivers to use this new ability.

While at it define hwif_chipset_t as u8 to save some space in hw_regs_t,
ide_hwif_t and ide_pci_device_t instances.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

hwif->chipset should be set to ide_cmd646 also when DMA base is invalid.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Majority of host drivers using IDE PCI layer set drive->autotune, the only
exceptions are:

generic.c
ns87415.c
rz1000.c
trm290.c
* no ->set_pio_mode method

it821x.c:
* if memory allocation fails drive->autotune won't be set
  (but there also won't be ->set_pio_mode method in such case)

piix.c:
* MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method)

However if there is no ->set_pio_mode method there are no changes in behavior
w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge init_setup_{cmd64x,cmd646}() into cmd64x_init_one().

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.

* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
  setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
  method may still override them).

* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.

While at it:

* Use ATA_{UDMA,MWDMA,SWDMA}* defines.

* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.

* serverworks.c: fix DMA masks being set before checking DMA base.

v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags.  Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define.  Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA.  Then remove no longer needed hwif->atapi_dma.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* hpt34x.c: disable DMA masks for HPT345
  (hwif->autodma is zero so DMA won't be enabled anyway).

* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
  (hwif->autodma is zero so DMA won't be enabled anyway).

* Check noautodma global variable instead of drive->autodma in ide_tune_dma().

  This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
  au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.

* Remove hwif->autodma (it was not checked by IDE core code anyway) and
  drive->autodma (was set by all host drivers - except HPT345/TRM290 special
  cases - unless "ide=nodma" was used).

While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
  (this setting was always later over-ridden by host drivers anyway)
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
  on BIOS for programming device/controller for DMA.  Set it in cy82c693,
  generic, ns87415, opti621 and trm290 host drivers.

* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA.  Set it in cs5520
  host driver.

* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.

* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
  implementations.  Fix all places checking for presence of ->ide_dma_check
  hook to check for ->ide_dma_on instead.

* Remove no longer needed code from config_drive_for_dma().

* Make ide_tune_dma() static.

v2:
* Fix config_drive_for_dma() return values.

* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
  dummy config_drive_for_dma() inline.

* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().

* Fix init_hwif_it8213() comment.

There should be no functionality changes caused by this patch.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning
has failed in ->ide_dma_check.  All host drivers using ide_use_fast_pio() set
drive->autotune so PIO is always tuned anyway and in some cases we _really_
need to re-tune PIO because PIO and DMA timings are shared.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.

* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program 
  the host for the transfer mode after programming the device.  Set it
  in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
  and via82cxxx host drivers.

* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
  skip programming of host/device for the transfer mode ("smart" hosts).
  Set it in it821x host driver and check it in ide_tune_dma().

* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
  direct ->set_pio_mode/->speedproc users to use these helpers.

* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
  methods to callers.

* Rename ->speedproc method to ->set_dma_mode, make it void and update
  all implementations accordingly.

* Update ide_set_xfer_rate() comments.

* Unexport ide_config_drive_speed().

v2:
* Fix issues noticed by Sergei:
  - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
    to setting DMA modes from sc1200_set_pio_mode() to do_special()
  - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
  - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
  - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
  - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
  - don't set ->set_{pio,dma}_mode on it821x in "smart" mode
  - fix build problem in pmac.c
  - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
  - improve patch description

Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
  PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
  the device (not really an issue since 0x00 is not supported correctly by
  any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.

v2:
* Fix pmac_ide_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
  and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.

* Add set_pio_mode_abuse() for checking if host driver has a non-standard
  ->tuneproc() implementation and use it in do_special().

* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
  the maximum PIO mode supported by the host), also add ide_set_max_pio()
  wrapper for ide_set_pio() to use for auto-tuning.  Convert users of
  ->tuneproc to use ide_set{_max}_pio() where possible.  This leaves only
  do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
  a direct users of ->tuneproc.

* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
  reporting PIO mode selected from ->tuneproc implementations.

* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.

* Remove stale comment from ide_config_drive_speed().

v2:
* Fix "ata_" prefix (Noticed by Jeff).

v3:
* Minor cleanups/fixups per Sergei's suggestions.

v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
  (Noticed by Andrew Morton).

* Improve some ->set_pio_mode comments.
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ide_rate_filter() calls from host drivers to IDE core.

* Make ide_rate_filter() static.

* Make 'speed' argument of ->speedproc const.

v2:
* Fix it8213_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix a couple of runtogether printks in cmd64x.c IDE driver by adding 
proper newlines.
Signed-off-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ATA_PIO[0-6] defines to <linux/ata.h>.

* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.

* Add PIO masks to host drivers.

<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
  and convert all users accordingly.

* Remove no longer needed ide_pio_data_t.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_pio_cycle_time() helper.

* Use it in ali14xx/ht6560b/qd65xx/cmd64{0,x}/sl82c105 and pmac host drivers
  (previously cycle time given by the device was only used for "pio" == 255).

* Remove no longer needed ide_pio_data_t.cycle_time field.

v2:
* Fix "ata_" prefix (Noticed by Jeff).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
  and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.

* Add IDE_HFLAG_SINGLE flag for single channel devices.

* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
  and remove no longer needed ide_pci_device_t.channels field.

v2:
* Fix issues noticed by Sergei:
  - correct code alignment in scc_pata.c
  - s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Print info about overriding PIO mode in ide_get_best_pio_mode().

* Remove info about overriding PIO mode from cmd64{0,x} host drivers.

* Remove no longer needed ide_pio_data_t.overridden field.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.

This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.

In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.

Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter.  Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.

Next patches add automatic detection of some systems using short cables.

Changes:

* Rename hwif->udma_four to hwif->cbl and make it u8.

* Convert all existing users accordingly (use ATA_CBL_* defines while at it).  

* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().

* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>

Fix two minor issues with PCI0646 chip reporting in the init_chipset() method:
"IRQ workaround enabled" message printed out not only for revision 0x01 and
"CMD646: chipset revision" printed twice (by IDE core and the driver itself).
Also, remove empty/pointless switch cases for the chips other than PCI0646,
duplicate write to the MRDMODE register when enabling interrupts and MEMORY
READ LINE cycles, and needless/misplaced initialization of the timing registers
in this method.
Switch to reading only the PCI revision ID register itself, not the whole 32
bits at its address in init_chipset() and init_hwif() methods; in addition,
get rid of the useless clearing of hwif->autodma and perform some cosmetic
style changes in the latter method.
Refactor ata66_cmd64x() by moving all the code into the 'switch' statement,
renaming/adding variables, and fixing the coding style.
While at it, finally get rid of the meaningless aliasing register #define's...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

All important information/features should be already available through
sysfs and ioctl interfaces.

Add CONFIG_IDE_PROC_FS (CONFIG_SCSI_PROC_FS rip-off) config option,
disabling it makes IDE driver ~5 kB smaller (on x86-32).

While at it add CONFIG_PROC_FS=n versions of proc_ide_{create,destroy}()
and remove no longer needed #ifdefs.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.

* add ide_hwif_t.udma_filter hook for filtering UDMA mask
  (use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
  (loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
  of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()

v2:
* rename ->filter_udma_mask to ->udma_filter
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
  originated transfer mode change requests when 100MHz clock is used)
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* use 0x00 instead of 0x80 to disable ->{ultra,mwdma,swdma}_mask
* add udma_mask field to ide_pci_device_t and use it to initialize
  ->ultra_mask in aec62xx, cmd64x, pdc202xx_{new,old} and piix drivers
* fix UDMA masks to match with chipset specific *_ratemask()
  (alim15x3, hpt366, serverworks and siimage drivers need UDMA mask
   filtering method - done in the next patch)

v2:
* piix: fix cable detection for 82801AA_1 and 82372FB_1
  [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* cmd64x: use hwif->cds->udma_mask
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* aec62xx: fix newly introduced bug - check DMA status not command register
  [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* piix: use hwif->cds->udma_mask
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fold the parts of the ide_dma_end() methods identical to __ide_dma_end() into a
mere call to it.
Start using faster versions of the ide_dma_end() and ide_dma_test_irq() methods
for the PCI0646U and newer chips that have the duplicate interrupt status bits
in the I/O mapped MRDMODE register, determing what methods to use at the driver
load time. Do some cleanup/renaming in the "old" ide_dma_test_irq() method too.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix several issues with the driver's procfs output:

- when testing if channel is enabled, the code looks at the "simplex" bits, not
  at the real enable bits -- add #define for the primary channel enable bit;

- UltraDMA modes 0, 1, 3 for slave drive reported incorrectly due to using the
  master drive's clock cycle resolution bit.

While at it, also perform the following cleanups:

- don't print extra newline before the first controller's dump;

- correct the chipset names (from CMDxxx to PCI-xxx)

- don't read from the registers which aren't used for dump;

- better align the table column sizes;

- rework UltraDMA mode dump code;

- remove PIO mode dump code that has never been finished;

- remove the duplicate interrupt status (the MRDMODE register bits mirror those
  those in the CFR and ARTTIM23 registers) and fold the dump into single line;

- correct the style of the ?: operators...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The IDE core looks at the wrong bit when checking if the secondary channel is
enabled on PCI0646 -- CNTRL register bit 7 is read-ahead disable, bit 3 is the
correct one.
Starting with PCI0646U chip, the primary channel can also be enabled/disabled --
so, add 'enablebits' initializers to each 'ide_pci_device_t' structure, handling
the original PCI0646 via adding the init_setup() method and clearing the 'reg'
field there if necessary...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver's ide_dma_test_irq() method was reading the MRDMODE register even on
PCI0643/6 where it was write-only -- fix this by always reading the "backward-
compatible" interrupt bits, renaming dma_alt_stat to irq_stat as the interrupt
status bits are not coupled to DMA.
In addition, wrong interrupt bit was tested/cleared for the primary channel --
it's bit 2 in all the chip specs and the driver used bit 1... :-/
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix the multiword DMA and drop the single-word DMA support (which nobody will
miss, I think).  In order to do it, a number of changes was necessary:

- rename program_drive_counts() to program_cycle_times(), pass to it cycle's
  total/active times instead of the clock counts, and convert them into the
  active/recovery clocks there instead of cmd64x_tune_pio() -- this causes
  quantize_timing() to also move;

- contrarywise, move all the code handling the address setup timing into
  cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup;

- remove from the speedproc() method the  bogus code pretending to set the DMA
  timings by twiddling bits in the BMIDE status register, handle setting MWDMA
  by just calling program_cycle_times(); while at it, improve the style of that
  whole switch statement;

- stop fiddling with the DMA capable bits in the speedproc() method -- they do
  not enable DMA, and are properly dealt with by the dma_host_{on,off} methods;

- don't set hwif->swdma_mask in the init_hwif() method anymore.

In addition to those changes, do the following:

- in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt
  status bit, eliminate local_irq_{save|restore}() around this code as there's
  *no* actual race with the interrupt handler, and move cmdprintk() to a more
  fitting place -- after ide_get_best_pio_mode() call;

- make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn;

- rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[];

- in  the speedproc() method, get rid of the duplicate reads/writes from/to the
  UDIDETCRx registers and of the extra variable used to store the transfer mode
  value after filtering,  use another method of determining master/slave drive,
  and cleanup useless parens;

- beautify cmdprintk() output here and there.

While at it, remove meaningless comment about the driver being used only on
UltraSPARC and long non-relevant RCS tag. :-)
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver wrongly takes the address setup time into account when calculating
the PIO recovery time -- this leads to slight overclocking of the PIO modes 0
and 1 (so, the prayers failed to help, as usual :-).  Rework the code to be
calculating recovery clock count as a difference between the total cycle count
and the active count (we don't need to calculate the recovery time itself since
it's not specified for the PIO modes 0 to 2, and for modes 3 and 4 this formula
gives enough recovery time anyway in the chip's supported PCI frequency range).

This patch has been inspired by reading the datasheets and looking at what the
libata driver does; it has been compile-tested only (as usual :-) but anyway,
the new code gives the same or longer recovery times than the old one...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to cmd64x_tune_pio(), making it return the mode set,
and "wrapping" the new tuneproc() method around it; while at it, also get rid
of the non-working prefetch control code (filtering out related argument values
in the "wrapper"), remove redundant PIO5 mode limitation, make cmdprintk() give
more sensible mode info, and remove mention about the obsolete /proc/ interface.
Get rid of the broken config_chipset_for_pio() which always tried to set PIO4,
switch to always auto-tuning PIO instead.
Oh, and add the missing PIO5 support to the speedproc() method while at it. :-)

Warning: compile tested only -- getting to the real hardware isn't that easy...

On Tuesday 06 February 2007 22:11, Mikael Pettersson <mikpe@it.uu.se> wrote:
> 
> Worked fine on my SPARC Ultra5 with a CMD646 IDE controller.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
  -1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
   0 when DMA needs to be enabled  (== need to call ->ide_dma_on)
   1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If DMA is unsupported ->ide_dma_check should disable DMA.

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>