The trigger that collects data when a frame is released
because of the timer of the reordering buffer was not
implemented for 9000 devices.
Fix this.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we get a valid baid in a received frame, we need to
check that we are aware of this baid. If not, we check
that the OLD_SN bit set. If that's not the case, we issue
a WARNING. Print more data when that happens.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we start an Rx A-MPDU session, we first get the AddBA
request, then we send an ADD_STA command to the firmware
that will reply with a BAID which is a hardware resource
that tracks the BA session.
This BAID will appear on each and every frame that we get
from the firwmare until the A-MPDU session is torn down.
In the Rx path, we look at this BAID to manage the
reordering buffer.

This flow is inherently racy since the hardware will start
to put the BAID in the frames it receives even if the
firmware hasn't sent the response to the ADD_STA command.
This basically means that the driver can get frames with
a valid BAID that it doesn't know yet.
When that happens, the driver used to WARN.
Fix this by simply not WARN in this case. When the driver
will know abou the BAID, it will initialise the relevant
states and the next frame with a valid BAID will refresh
them.

Fixes: b915c101 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Convention has it to byte-swap the constant instead of the variable
when doing bit checks. This also generates better code when the swap
is actually needed, since the constant can be swapped at compile-time.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Since we exit if buf->num_stored is 0, there's no need to
check it again later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.

An spatch similar to the one for skb_put_zero() converts many
of the places using it:

    @@
    identifier p, p2;
    expression len, skb, data;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, len);
    |
    -memcpy(p, data, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb, data;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, sizeof(*p));
    |
    -memcpy(p, data, sizeof(*p));
    )

    @@
    expression skb, len, data;
    @@
    -memcpy(skb_put(skb, len), data, len);
    +skb_put_data(skb, data, len);

(again, manually post-processed to retain some comments)
Reviewed-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This field will need to be used again for HE, so rename it now.

Again, mostly done with this spatch:

@@
expression status;
@@
-status->vht_nss
+status->nss
@@
expression status;
@@
-status.vht_nss
+status.nss
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We currently use a lot of flags that are mutually incompatible,
separate this out into actual encoding and bandwidth enum values.

Much of this again done with spatch, with manual post-editing,
mostly to add the switch statements and get rid of the conversions.

@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_80MHZ
+status->bw = RATE_INFO_BW_80
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_40MHZ
+status->bw = RATE_INFO_BW_40
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_20MHZ
+status->bw = RATE_INFO_BW_20
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_160MHZ
+status->bw = RATE_INFO_BW_160
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_5MHZ
+status->bw = RATE_INFO_BW_5
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_10MHZ
+status->bw = RATE_INFO_BW_10

@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_VHT
+status->encoding = RX_ENC_VHT
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_HT
+status->encoding = RX_ENC_HT
@@
expression status;
@@
-status.enc_flags |= RX_ENC_FLAG_VHT
+status.encoding = RX_ENC_VHT
@@
expression status;
@@
-status.enc_flags |= RX_ENC_FLAG_HT
+status.encoding = RX_ENC_HT

@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_HT)
+(status->encoding == RX_ENC_HT)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_VHT)
+(status->encoding == RX_ENC_VHT)

@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_5MHZ)
+(status->bw == RATE_INFO_BW_5)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_10MHZ)
+(status->bw == RATE_INFO_BW_10)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_40MHZ)
+(status->bw == RATE_INFO_BW_40)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_80MHZ)
+(status->bw == RATE_INFO_BW_80)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_160MHZ)
+(status->bw == RATE_INFO_BW_160)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In preparation for adding support for HE rates, clean up
the driver report encoding for rate/bandwidth reporting
on RX frames.

Much of this patch was done with the following spatch:

@@
expression status;
@@
-status->flag & (RX_FLAG_HT | RX_FLAG_VHT)
+status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT)

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_SHORTPRE
+status->enc_flags op RX_ENC_FLAG_SHORTPRE
@@
expression status;
@@
-status->flag & RX_FLAG_SHORTPRE
+status->enc_flags & RX_ENC_FLAG_SHORTPRE

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_HT
+status->enc_flags op RX_ENC_FLAG_HT
@@
expression status;
@@
-status->flag & RX_FLAG_HT
+status->enc_flags & RX_ENC_FLAG_HT

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_40MHZ
+status->enc_flags op RX_ENC_FLAG_40MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_40MHZ
+status->enc_flags & RX_ENC_FLAG_40MHZ

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_SHORT_GI
+status->enc_flags op RX_ENC_FLAG_SHORT_GI
@@
expression status;
@@
-status->flag & RX_FLAG_SHORT_GI
+status->enc_flags & RX_ENC_FLAG_SHORT_GI

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_HT_GF
+status->enc_flags op RX_ENC_FLAG_HT_GF
@@
expression status;
@@
-status->flag & RX_FLAG_HT_GF
+status->enc_flags & RX_ENC_FLAG_HT_GF

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_VHT
+status->enc_flags op RX_ENC_FLAG_VHT
@@
expression status;
@@
-status->flag & RX_FLAG_VHT
+status->enc_flags & RX_ENC_FLAG_VHT

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_STBC_MASK
+status->enc_flags op RX_ENC_FLAG_STBC_MASK
@@
expression status;
@@
-status->flag & RX_FLAG_STBC_MASK
+status->enc_flags & RX_ENC_FLAG_STBC_MASK

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_LDPC
+status->enc_flags op RX_ENC_FLAG_LDPC
@@
expression status;
@@
-status->flag & RX_FLAG_LDPC
+status->enc_flags & RX_ENC_FLAG_LDPC

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_10MHZ
+status->enc_flags op RX_ENC_FLAG_10MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_10MHZ
+status->enc_flags & RX_ENC_FLAG_10MHZ

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_5MHZ
+status->enc_flags op RX_ENC_FLAG_5MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_5MHZ
+status->enc_flags & RX_ENC_FLAG_5MHZ

@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_80MHZ
+status->enc_flags op RX_ENC_FLAG_80MHZ
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_80MHZ
+status->enc_flags & RX_ENC_FLAG_80MHZ

@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_160MHZ
+status->enc_flags op RX_ENC_FLAG_160MHZ
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_160MHZ
+status->enc_flags & RX_ENC_FLAG_160MHZ

@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_BF
+status->enc_flags op RX_ENC_FLAG_BF
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_BF
+status->enc_flags & RX_ENC_FLAG_BF

@@
assignment operator op;
expression status, STBC;
@@
-status->flag op STBC << RX_FLAG_STBC_SHIFT
+status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_SHORTPRE
+status.enc_flags op RX_ENC_FLAG_SHORTPRE
@@
expression status;
@@
-status.flag & RX_FLAG_SHORTPRE
+status.enc_flags & RX_ENC_FLAG_SHORTPRE

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_HT
+status.enc_flags op RX_ENC_FLAG_HT
@@
expression status;
@@
-status.flag & RX_FLAG_HT
+status.enc_flags & RX_ENC_FLAG_HT

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_40MHZ
+status.enc_flags op RX_ENC_FLAG_40MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_40MHZ
+status.enc_flags & RX_ENC_FLAG_40MHZ

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_SHORT_GI
+status.enc_flags op RX_ENC_FLAG_SHORT_GI
@@
expression status;
@@
-status.flag & RX_FLAG_SHORT_GI
+status.enc_flags & RX_ENC_FLAG_SHORT_GI

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_HT_GF
+status.enc_flags op RX_ENC_FLAG_HT_GF
@@
expression status;
@@
-status.flag & RX_FLAG_HT_GF
+status.enc_flags & RX_ENC_FLAG_HT_GF

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_VHT
+status.enc_flags op RX_ENC_FLAG_VHT
@@
expression status;
@@
-status.flag & RX_FLAG_VHT
+status.enc_flags & RX_ENC_FLAG_VHT

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_STBC_MASK
+status.enc_flags op RX_ENC_FLAG_STBC_MASK
@@
expression status;
@@
-status.flag & RX_FLAG_STBC_MASK
+status.enc_flags & RX_ENC_FLAG_STBC_MASK

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_LDPC
+status.enc_flags op RX_ENC_FLAG_LDPC
@@
expression status;
@@
-status.flag & RX_FLAG_LDPC
+status.enc_flags & RX_ENC_FLAG_LDPC

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_10MHZ
+status.enc_flags op RX_ENC_FLAG_10MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_10MHZ
+status.enc_flags & RX_ENC_FLAG_10MHZ

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_5MHZ
+status.enc_flags op RX_ENC_FLAG_5MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_5MHZ
+status.enc_flags & RX_ENC_FLAG_5MHZ

@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_80MHZ
+status.enc_flags op RX_ENC_FLAG_80MHZ
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_80MHZ
+status.enc_flags & RX_ENC_FLAG_80MHZ

@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_160MHZ
+status.enc_flags op RX_ENC_FLAG_160MHZ
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_160MHZ
+status.enc_flags & RX_ENC_FLAG_160MHZ

@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_BF
+status.enc_flags op RX_ENC_FLAG_BF
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_BF
+status.enc_flags & RX_ENC_FLAG_BF

@@
assignment operator op;
expression status, STBC;
@@
-status.flag op STBC << RX_FLAG_STBC_SHIFT
+status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT

@@
@@
-RX_FLAG_STBC_SHIFT
+RX_ENC_FLAG_STBC_SHIFT
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Rates were changed to adapt to HE. Change is backward compatible.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Address 4 is reversed as well.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently when rate isn't found (invalid rate or CCK rate in high
band) driver is assigning rate -1, which causes mac80211 to dump
it later with the cryptic rate value of 0xFF.
Instead, warn early and dump the frame in mvm.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we get SN that is smaller than SSN of the aggregation,
we shouldn't apply any reordering on them.
Further more, HW NSSN will be zeroed, which can cause us
to make some invalid decisions.
Detect the situation and invalidate the BAID.

Fixes: b915c101 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Seems like HW is reversing addr3 in the MAC header of de-aggregated
AMSDU. Reverse it back.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This flag is used for mac80211 reordering. As we do reordering
ourselves, turning it on is misleading and pointless.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In a000 devices we will support up to 32 stations.
The max station define is used also for invalid station marking
which makes finding usages of actual maximum station pretty hard
to sort through - change it to be a different define in order
to make future changes easier.
Use also ARRAY_SIZE intead of define when possible.
Do not move yet to 32 stations until firmware do it though.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently we release up to the last expired frame.
However, if there are consecutive frames after it - we can
optimize it further and release them as well - until the next
hole.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When NSSN is behind the reorder buffer due to timeout
the reorder timer isn't getting re-armed until NSSN
catches up. Fix it.

Fixes: 0690405f ("iwlwifi: mvm: add reorder timeout per frame")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When a small frame is copied completely into the skb->head, the code
doesn't take alignment into account, making mac80211 copy it again
later on architectures that need the alignment. Avoid this by taking
the PAD flag from the device into account when copying.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we sync the RX queues the driver waits to receive echo
notification on all the RX queues.
The wait queue is set with timeout until all queues have received
the notification.
However, iwl_mvm_rx_queue_notif() never woke up the wait queue,
with the result of the counter value being checked only when the
timeout expired.
This may cause a latency of up to 1 second.

Fixes: 0636b938 ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we get an unexpected Block Ack Request frame, the BAID from
the hardware will be invalid, and we'll pass it to mac80211 for
further handling (sending a delBA action frame.)

Add a comment explaining that, in case anyone looks in the future.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

On default queue we will not receive frame release notification,
but the BAR itself.
Upon receiving the BAR driver should look at the NSSN and adjust
window accordingly.

Fixes: b915c101 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Use skb_queue_empty() and not skb_peek_tail() to check for
empty list.
Avoid a redundant check as well - loop will take care of it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As pointed out by smatch, checking the BAID for just >= INVALID
is a bad idea since only 32 (IWL_MAX_BAID) actually exist. Check
the range for that and print invalid ones in the warning.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Inside the reorder timer expire function, there's no point in
disabling BHs since it is in BH context. Remove that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The 9000 hardware will de-aggregate AMSDUs. In the process
it will copy the mac header "as is" to the new MPDUs.
This means driver should allow the same PN for MPDUs originated
from the same AMSDU.
Do that by incrementing the PN only for the last MPDU in the
sequence.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add some prints to track BAID assignment.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add support CSA countdown offloading. When CSA starts, the driver
specifies the offsets to the eCSA and CSA IEs in the beacon template
command and the fw performs the countdown.
The fw notifies the driver when the channel switch flow
should be performed.
Beacon sent notifications are not used anymore.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

rx_phy notification is no longer sent in devices with
multiple rx queues.
All the needed data is now set in the metadata - update
code accordingly to reflect all the features as in the
previous RX path.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In multiple RX queues architecture, the RX_PHY notification
is no longer useful as it is received in the default queue
even for packets that are received on RSS queue, and cannot
be accessed without locking.
All the needed data is in the new RX packet metadata and
firmware will no longer send this notification for 9000
devices. Remove support of it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We cannot trust NSSN for AMSDU sub-frames that are not the
last.
The reason is that NSSN advances on the first sub-frame,
and may cause the reorder buffer to advance before all the
sub-frames arrive.
Example:
Reorder buffer contains SN 0 & 2.
We receive AMSDU with SN 1 and NSSN for first sub frame 3.
The result us that driver releases SN 0,1, 2.
When sub-frame 1 arrives - reorder buffer is already ahead and
it will be dropped.
If the last sub-frame is not on this queue - we will get frame
release notification with up to date NSSN.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We try to access sta before we check for IS_ERR_OR_NULL(), so we may
end up accessing a NULL pointer.  To prevent that, move the conversion
from sta to mvm_sta below the check.

Fixes: b915c101 ("iwlwifi: mvm: add reorder buffer per queue")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Up till now, the reorder buffer uses standard spec based comparison
when comparing the buffer status to NSSN. This indeed works for the
regular case, since we shouldn't cross the 2048 boundary without
getting a frame release notification.
However, this is problematic due to packet filtering that may be
performed by the FW while we are in d0i3. Theoretically we may
filter over 2048 packets, and then the check of the NSSN will get
incorrect.
Change the comparison to always trust nssn unless it is 64 or less
frames behind the head - which might happen due to a timeout.
This new comparison is to be used only when comparing reorder buffer
head with nssn, and not when comparing the packet SN to nssn or
reorder buffer head.
Put this in a separate commit as the logic is a bit tricky and
stands for its own commit message.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we've already looked up the transmitter station, we can just
pass it to mac80211 using the new ieee80211_rx_napi(). This saves
the overhead of looking it up in mac80211 again.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The firmware will send frame release notification in order
to release "stuck" frames on a queue where no more frames
arrive on.
Upon receiving the message the driver shall indicate the frames
up to the NSSN.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add a timer in order to release expired frames from the
reorder buffer.
This is needed since some APs do not retransmit frames
to fill in the reorder holes and in TCP it results with
a complete stall of traffic.

This has a few side effects on the general design:

The nssn may not reflect the the head of the reorder buffer.
This situation is valid, and packets with SN lower than the
reorder buffer head will be dropped.

Another side effect is that since the reorder timer might expire
we need to lock the reorder buffer.
This however is fine since the locking is only inside a
single reorder buffer between RX path and reorder timeout and
there is no outside contention.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Next hardware will direct packets to core based on the TCP/UDP
streams.
This logic can create holes in reorder buffer since packets that
belong to other stream were directed to a different core.
However, those are valid holes and the packets can be indicated
in L3 order.

The hardware will utilize a mechanism of informing the driver of
the normalized ssn and the driver shall release all packets that
SN is lower than the nssn.
This enables managing the reorder across the queues without sharing
any data between them.

The reorder buffer is allocated and released directly in the RX path
in order to avoid various races between control path and rx path.
The code utilizes the internal messaging to notify rx queues of when
to delete the reorder buffer.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

According to the spec when a BA session is started there
is a timeout set for the session in the ADDBA request.
If there is not activity on the TA/TID then the session
expires and a DELBA is sent.
In order to check for the timeout, data must be shared
among the rx queues.
Add a timer that runs as long as BA session is active
for the station and stops aggregation session if needed.
This patch also lays the infrastructure for the reordering
buffer which will be enabled in the next patches.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently the sync notification is a type of notification. However, it
is better fitted as an attribute of a notification, since there might
be another message in the payload (delba for instance) that should be
sent while control path is waiting for all queues to process.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>