The  TXALCR1 offsets are incorrect in the register offset tables, most
probably due to copy&paste error.  Luckily, the driver never uses this
register. :-)

Fixes: 4a55530f ("net: sh_eth: modify the definitions of register")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.

Fixes: 4bdcb1dd ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 1463447 ("Missing break in switch")
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner says:

====================
SCTP PMTU discovery fixes

This patchset fixes 2 issues with PMTU discovery that can lead to flood
of retransmissions.
The first patch fixes the issue for when PMTUD is disabled by the
application, while the second fixes it for when its enabled.

Please consider these to stable.
====================
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

syzbot reported a hang involving SCTP, on which it kept flooding dmesg
with the message:
[  246.742374] sctp: sctp_transport_update_pmtu: Reported pmtu 508 too
low, using default minimum of 512

That happened because whenever SCTP hits an ICMP Frag Needed, it tries
to adjust to the new MTU and triggers an immediate retransmission. But
it didn't consider the fact that MTUs smaller than the SCTP minimum MTU
allowed (512) would not cause the PMTU to change, and issued the
retransmission anyway (thus leading to another ICMP Frag Needed, and so
on).

As IPv4 (ip_rt_min_pmtu=556) and IPv6 (IPV6_MIN_MTU=1280) minimum MTU
are higher than that, sctp_transport_update_pmtu() is changed to
re-fetch the PMTU that got set after our request, and with that, detect
if there was an actual change or not.

The fix, thus, skips the immediate retransmission if the received ICMP
resulted in no change, in the hope that SCTP will select another path.

Note: The value being used for the minimum MTU (512,
SCTP_DEFAULT_MINSEGMENT) is not right and instead it should be (576,
SCTP_MIN_PMTU), but such change belongs to another patch.

Changes from v1:
- do not disable PMTU discovery, in the light of commit
06ad3919 ("[SCTP] Don't disable PMTU discovery when mtu is small")
and as suggested by Xin Long.
- changed the way to break the rtx loop by detecting if the icmp
  resulted in a change or not
Changes from v2:
none

See-also: https://lkml.org/lkml/2017/12/22/811Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, if PMTU discovery is disabled on a given transport, but the
configured value is higher than the actual PMTU, it is likely that we
will get some icmp Frag Needed. The issue is, if PMTU discovery is
disabled, we won't update the information and will issue a
retransmission immediately, which may very well trigger another ICMP,
and another retransmission, leading to a loop.

The fix is to simply not trigger immediate retransmissions if PMTU
discovery is disabled on the given transport.

Changes from v2:
- updated stale comment, noticed by Xin Long
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.

The guest would face errors like:

  [root@guest ~]# ethtool -i eth0
  Cannot get driver information: No such device

  [root@guest ~]# ifconfig eth0
  eth0: error fetching interface information: Device not found

This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.
Signed-off-by: NEduardo Otubo <otubo@redhat.com>
Reviewed-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: 2 small bug fixes.

The first one fixes the TC Flower flow parameter passed to firmware.  The
2nd one fixes the VF index range checking for iproute2 SRIOV related commands.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NVenkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

flow_type in HWRM_FLOW_ALLOC is not being populated correctly due to
incorrect passing of pointer and size of l3_mask argument of is_wildcard().
Fixed this.

Fixes: db1d36a2 ("bnxt_en: add TC flower offload flow_alloc/free FW cmds")
Signed-off-by: NSunil Challa <sunilkumar.challa@broadcom.com>
Reviewed-by: NSathya Perla <sathya.perla@broadcom.com>
Reviewed-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Renesas  SH7757 has 2 Fast and 2 Gigabit Ether controllers, while the
'sh_eth' driver can only reset and initialize TSU of the first controller
pair. Shimoda-san tried to solve that adding the 'needs_init' member to the
'struct sh_eth_plat_data', however the platform code still never sets this
flag. I think  that we can infer this information from the 'devno' variable
(set  to 'platform_device::id') and reset/init the Ether controller pair
only for an even 'devno'; therefore 'sh_eth_plat_data::needs_init' can be
removed...

Fixes: 150647fb ("net: sh_eth: change the condition of initialization")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.15-20180104' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2018-01-04

this is a pull request for net/master consisting of 4 patches.

The first patch is by Oliver Hartkopp, it improves the error checking
during the creation of a vxcan link. Wolfgang Grandegger's patch for the
gs_usb driver fixes the return value of the "set_bittiming" callback.
Luu An Phu provides a patch for the flexcan driver to fix the frame
length check in the flexcan_start_xmit() function. The last patch is by
Martin Lederhilger for the ems_usb driver and improves the error
reporting for error warning and passive frames.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes in probe error path:
- Restore dev_id before failed_ioremap path.
  Fixes: ("net: fec: restore dev_id in the cases of probe error")
- Call of_node_put(phy_node) before failed_phy path.
  Fixes: ("net: fec: Support phys probed from devicetree and fixed-link")
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Fix chain filtering when dumping rules via nf_tables_dump_rules().

2) Fix accidental change in NF_CT_STATE_UNTRACKED_BIT through uapi,
   introduced when removing the untracked conntrack object, from
   Florian Westphal.

3) Fix potential nul-dereference when releasing dump filter in
   nf_tables_dump_obj_done(), patch from Hangbin Liu.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Musl provides its own ethhdr struct definition. Add a guard to prevent
its definition of the appropriate musl header has already been included.

glibc does not implement this header, but when glibc will implement this
they can just define __UAPI_DEF_ETHHDR 0 to make it work with the
kernel.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In fib6_add(), pn could be NULL if fib6_add_1() failed to return a fib6
node. Checking pn != fn before accessing pn->leaf makes sure pn is not
NULL.
This fixes the following GPF reported by syzkaller:
general protection fault: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
   (ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 3201 Comm: syzkaller001778 Not tainted 4.15.0-rc5+ #151
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:fib6_add+0x736/0x15a0 net/ipv6/ip6_fib.c:1244
RSP: 0018:ffff8801c7626a70 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 0000000000000020 RCX: ffffffff84794465
RDX: 0000000000000004 RSI: ffff8801d38935f0 RDI: 0000000000000282
RBP: ffff8801c7626da0 R08: 1ffff10038ec4c35 R09: 0000000000000000
R10: ffff8801c7626c68 R11: 0000000000000000 R12: 00000000fffffffe
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000009
FS:  0000000000000000(0000) GS:ffff8801db200000(0063) knlGS:0000000009b70840
CS:  0010 DS: 002b ES: 002b CR0: 0000000080050033
CR2: 0000000020be1000 CR3: 00000001d585a006 CR4: 00000000001606f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 __ip6_ins_rt+0x6c/0x90 net/ipv6/route.c:1006
 ip6_route_multipath_add+0xd14/0x16c0 net/ipv6/route.c:3833
 inet6_rtm_newroute+0xdc/0x160 net/ipv6/route.c:3957
 rtnetlink_rcv_msg+0x733/0x1020 net/core/rtnetlink.c:4411
 netlink_rcv_skb+0x21e/0x460 net/netlink/af_netlink.c:2408
 rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4423
 netlink_unicast_kernel net/netlink/af_netlink.c:1275 [inline]
 netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1301
 netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1864
 sock_sendmsg_nosec net/socket.c:636 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:646
 sock_write_iter+0x31a/0x5d0 net/socket.c:915
 call_write_iter include/linux/fs.h:1772 [inline]
 do_iter_readv_writev+0x525/0x7f0 fs/read_write.c:653
 do_iter_write+0x154/0x540 fs/read_write.c:932
 compat_writev+0x225/0x420 fs/read_write.c:1246
 do_compat_writev+0x115/0x220 fs/read_write.c:1267
 C_SYSC_writev fs/read_write.c:1278 [inline]
 compat_SyS_writev+0x26/0x30 fs/read_write.c:1274
 do_syscall_32_irqs_on arch/x86/entry/common.c:327 [inline]
 do_fast_syscall_32+0x3ee/0xf9d arch/x86/entry/common.c:389
 entry_SYSENTER_compat+0x54/0x63 arch/x86/entry/entry_64_compat.S:125
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Fixes: 66f5d6ce ("ipv6: replace rwlock with rcu and spinlock in fib6_table")
Signed-off-by: NWei Wang <weiwan@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

set rm->atomic.op_active to 0 when rds_pin_pages() fails
or the user supplied address is invalid,
this prevents a NULL pointer usage in rds_atomic_free_op()
Signed-off-by: NMohamed Ghannam <simo.ghannam@gmail.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When switching  the driver to the managed device API,  I managed to break
the  case of a  dual Ether devices sharing a single TSU: the 2nd Ether port
wouldn't probe. Iwamatsu-san has tried to fix this but his patch was buggy
and he then dropped the ball...

The solution is to  limit calling devm_request_mem_region() to the first
of  the two  ports  sharing the same TSU, so devm_ioremap_resource() can't
be used anymore for the TSU resource...

Fixes: d5e07e69 ("sh_eth: use managed device API")
Reported-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Note in the databook - Section 4.4 - EEE :
" The EEE feature is not supported when the MAC is configured to use the
TBI, RTBI, SMII, RMII or SGMII single PHY interface. Even if the MAC
supports multiple PHY interfaces, you should activate the EEE mode only
when the MAC is operating with GMII, MII, or RGMII interface."

Applying this restriction solves a stability issue observed on Amlogic
gxl platforms operating with RMII interface and the internal PHY.

Fixes: 83bf79b6 ("stmmac: disable at run-time the EEE if not supported")
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Tested-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function is used from two places: rtnl_dump_ifinfo and
rtnl_getlink. In rtnl_getlink(), we give a request skb into
get_target_net(), but in rtnl_dump_ifinfo, we give a response skb
into get_target_net().
The problem here is that NETLINK_CB() isn't initialized for the response
skb. In both cases we can get a user socket and give it instead of skb
into get_target_net().

This bug was found by syzkaller with this call-trace:

kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 1 PID: 3149 Comm: syzkaller140561 Not tainted 4.15.0-rc4-mm1+ #47
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:__netlink_ns_capable+0x8b/0x120 net/netlink/af_netlink.c:868
RSP: 0018:ffff8801c880f348 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff8443f900
RDX: 000000000000007b RSI: ffffffff86510f40 RDI: 00000000000003d8
RBP: ffff8801c880f360 R08: 0000000000000000 R09: 1ffff10039101e4f
R10: 0000000000000000 R11: 0000000000000001 R12: ffffffff86510f40
R13: 000000000000000c R14: 0000000000000004 R15: 0000000000000011
FS:  0000000001a1a880(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020151000 CR3: 00000001c9511005 CR4: 00000000001606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
  netlink_ns_capable+0x26/0x30 net/netlink/af_netlink.c:886
  get_target_net+0x9d/0x120 net/core/rtnetlink.c:1765
  rtnl_dump_ifinfo+0x2e5/0xee0 net/core/rtnetlink.c:1806
  netlink_dump+0x48c/0xce0 net/netlink/af_netlink.c:2222
  __netlink_dump_start+0x4f0/0x6d0 net/netlink/af_netlink.c:2319
  netlink_dump_start include/linux/netlink.h:214 [inline]
  rtnetlink_rcv_msg+0x7f0/0xb10 net/core/rtnetlink.c:4485
  netlink_rcv_skb+0x21e/0x460 net/netlink/af_netlink.c:2441
  rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4540
  netlink_unicast_kernel net/netlink/af_netlink.c:1308 [inline]
  netlink_unicast+0x4be/0x6a0 net/netlink/af_netlink.c:1334
  netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1897

Cc: Jiri Benc <jbenc@redhat.com>
Fixes: 79e1ad14 ("rtnetlink: use netnsid to query interface")
Signed-off-by: NAndrei Vagin <avagin@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPravin Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2018-01-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Two fixes:
 * drop mesh frames appearing to be from ourselves
 * check another netlink attribute for existence
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the missing CAN_ERR_CRTL to cf->can_id in case of
CAN_STATE_ERROR_WARNING or CAN_STATE_ERROR_PASSIVE
Signed-off-by: NMartin Lederhilger <m.lederhilger@ds-automotion.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The flexcan_start_xmit() function compares the frame length with data
register length to write frame content into data[0] and data[1]
register. Data register length is 4 bytes and frame maximum length is 8
bytes.

Fix the check that compares frame length with 3. Because the register
length is 4.
Signed-off-by: NLuu An Phu <phu.luuan@nxp.com>
Reviewed-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The "set_bittiming" callback treats a positive return value as error!
For that reason "can_changelink()" will quit silently after setting
the bittiming values without processing ctrlmode, restart-ms, etc.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Picking up the patch from Serhey Popovych (commit 191cdb38,
"veth: Be more robust on network device creation when no attributes").

When the peer name attribute is not provided the former implementation tries
to register the given device name twice ... which leads to -EEXIST.
If only one device name is given apply an automatic generated and valid name
for the peer.

Cc: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Models such as BCM5395/97/98 and BCM53125/24/53115 and compatible require that
we turn on managed mode to actually act on Broadcom tags, otherwise they just
pass them through on ingress (host -> switch) and don't insert them in egress
(switch -> host). Turning on managed mode is simple, but requires us to
properly support ARL misses on multicast addresses which is a much more
involved set of changes not suitable for a bug fix for this release.
Reported-by: NJochen Friedrich <jochen@scram.de>
Fixes: 7edc58d6 ("net: dsa: b53: Turn on Broadcom tags")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If there are multiple mesh stations with the same MAC address,
they will both get confused and start throwing warnings.

Obviously in this case nothing can actually work anyway, so just
drop frames that look like they're from ourselves early on.
Reported-by: NGui Iribarren <gui@altermundi.net>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

nl80211_nan_add_func() does not check if the required attribute
NL80211_NAN_FUNC_FOLLOW_UP_DEST is present when processing
NL80211_CMD_ADD_NAN_FUNCTION request. This request can be issued
by users with CAP_NET_ADMIN privilege and may result in NULL dereference
and a system crash. Add a check for the required attribute presence.
Signed-off-by: NHao Chen <flank3rsky@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2018-01-03

This series contains fixes for i40e and i40evf.

Amritha removes the UDP support for big buffer cloud filters since it is
not supported and having UDP enabled is a bug.

Alex fixes a bug in the __i40e_chk_linearize() which did not take into
account large (16K or larger) fragments that are split over 2 descriptors,
which could result in a transmit hang.

Jake fixes an issue where a devices own MAC address could be removed from
the unicast address list, so force a check on every address sync to ensure
removal does not happen.

Jiri Pirko fixes the return value when a filter configuration is not
supported, do not return "invalid" but return "not supported" so that
the core can react correctly.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A few spots in 3c59x missed calls to dma_mapping_error checks, casuing
WARN_ONS to trigger.  Clean those up.  While we're at it, refactor the
refill code a bit so that if skb allocation or dma mapping fails, we
recycle the existing buffer.  This prevents holes in the rx ring, and
makes for much simpler logic

Note: This is compile only tested.  Ted, if you could run this and
confirm that it continues to work properly, I would appreciate it, as I
currently don't have access to this hardware
Signed-off-by: NNeil Horman <nhorman@redhat.com>
CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: tedheadster@gmail.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Netanel Belgazal says:

====================
bug fixes for ENA Ethernet driver

Changes from V1:
Revome incorrect "ena: invoke netif_carrier_off() only after netdev
  registered" patch

This patchset contains 2 bug fixes:
* handle rare race condition during MSI-X initialization
* fix error processing in ena_down()
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ENA admin command queue errors are not handled as part of ena_down().
As a result, in case of error admin queue transitions to non-running
state and aborts all subsequent commands including those coming from
ena_up(). Reset scheduled by the driver from the timer service
context would not proceed due to sharing rtnl with ena_up()/ena_down()
Signed-off-by: NNetanel Belgazal <netanel@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under certain conditions MSI-X interrupt might arrive right after it
was unmasked in ena_up(). There is a chance it would be processed by
the driver before device ENA_FLAG_DEV_UP flag is set. In such a case
the interrupt is ignored.
ENA device operates in auto-masked mode, therefore ignoring
interrupt leaves it masked for good.
Moving unmask of interrupt to be the last step in ena_up().
Signed-off-by: NNetanel Belgazal <netanel@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 96ac18f1 ("cxgb4: Add support for new flash parts")
removed initialization of adapter->params.sf_fw_start causing issues
while flashing firmware to card. We no longer need sf_fw_start
in adapter->params as we already have macros defined for FW flash
addresses.

Fixes: 96ac18f1 ("cxgb4: Add support for new flash parts")
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When filter configuration is not supported, drivers should return
-EOPNOTSUPP so the core can react correctly.

Fixes: 2f4b411a ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In some circumstances, such as with bridging, it is possible that the
stack will add a devices own MAC address to its unicast address list.

If, later, the stack deletes this address, then the i40e driver will
receive a request to remove this address.

The driver stores its current MAC address as part of the MAC/VLAN hash
array, since it is convenient and matches exactly how the hardware
expects to be told which traffic to receive.

This causes a problem, since for more devices, the MAC address is stored
separately, and requests to delete a unicast address should not have the
ability to remove the filter for the MAC address.

Fix this by forcing a check on every address sync to ensure we do not
remove the device address.

There is a very narrow possibility of a race between .set_mac and
.set_rx_mode, if we don't change netdev->dev_addr before updating our
internal MAC list in .set_mac. This might be possible if .set_rx_mode is
going to remove MAC "XYZ" from the list, at the same time as .set_mac
changes our dev_addr to MAC "XYZ", we might possibly queue a delete,
then an add in .set_mac, then queue a delete in .set_rx_mode's
dev_uc_sync and then update netdev->dev_addr. We can avoid this by
moving the copy into dev_addr prior to the changes to the MAC filter
list.

A similar race on the other side does not cause problems, as if we're
changing our MAC form A to B, and we race with .set_rx_mode, it could
queue a delete from A, we'd update our address, and allow the delete.
This seems like a race, but in reality we're about to queue a delete of
A anyways, so it would not cause any issues.

A race in the initialization code is unlikely because the netdevice has
not yet been fully initialized and the stack should not be adding or
removing addresses yet.

Note that we don't (yet) need similar code for the VF driver because it
does not make use of __dev_uc_sync and __dev_mc_sync, but instead roles
its own method for handling updates to the MAC/VLAN list, which already
has code to protect against removal of the hardware address.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The original code for __i40e_chk_linearize didn't take into account the
fact that if a fragment is 16K in size or larger it has to be split over 2
descriptors and the smaller of those 2 descriptors will be on the trailing
edge of the transmit. As a result we can get into situations where we didn't
catch requests that could result in a Tx hang.

This patch takes care of that by subtracting the length of all but the
trailing edge of the stale fragment before we test for sum. By doing this
we can guarantee that we have all cases covered, including the case of a
fragment that spans multiple descriptors. We don't need to worry about
checking the inner portions of this since 12K is the maximum aligned DMA
size and that is larger than any MSS will ever be since the MTU limit for
jumbos is something on the order of 9K.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fugang Duan says:

====================
net: fec: clean up in the cases of probe error

The simple patches just clean up in the cases of probe error like restore dev_id and
handle the defer probe when regulator is still not ready.

v2:
* Fabio Estevam's comment to suggest split v1 to separate patches.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Defer probe if regulator is not ready. E.g. some regulator is fixed
regulator controlled by i2c expander gpio, the i2c device may be probed
after the driver, then it should handle the case of defer probe error.
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>