Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 13 3月, 2014 16 次提交
  3. 12 3月, 2014 1 次提交
  5. 11 3月, 2014 6 次提交
    • T
      net: eth: cpsw: Use net_device_stats from struct net_device · 8dc43ddc
      由 Tobias Klauser 提交于 
      Instead of using an own copy of struct net_device_stats in struct
cpsw_priv, use stats from struct net_device. Also remove the thus
unnecessary .ndo_get_stats function, as it just returns dev->stats,
which is the default.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8dc43ddc
    • T
      sky2: allow mac to come from dt · 3ee2f8ce
      由 Tim Harvey 提交于 
      The driver reads the mac address from the device registers which would
need to have been programmed by the bootloader.  This patch adds
the ability to pull the mac from devicetree via the pci device dt node.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>

Changes since v2:
 - eliminated use of stack tmpaddr per feedback

Changes since v1:
 - simplified based on feedback
 - fixed formatting
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3ee2f8ce
    • K
      IB/mlx5_core: remove unreachable function call in module init · c120e9e0
      由 Kleber Sacilotto de Souza 提交于 
      The call to mlx5_health_cleanup() in the module init function can never
be reached. Removing it.
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c120e9e0
    • E
      sfc: Use ether_addr_copy and eth_broadcast_addr · cd84ff4d
      由 Edward Cree 提交于 
      Faster than memcpy/memset on some architectures.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      cd84ff4d
    • C
      gianfar: Use Single-Queue polling for "fsl,etsec2" · 71ff9e3d
      由 Claudiu Manoil 提交于 
      For the "fsl,etsec2" compatible models the driver currently
supports 8 Tx and Rx DMA rings (aka HW queues).  However, there
are only 2 pairs of Rx/Tx interrupt lines, as these controllers
are integrated in low power SoCs with 2 CPUs at most.  As a result,
there are at most 2 NAPI instances that have to service multiple
Tx and Rx queues for these devices.  This complicates the NAPI
polling routine having to iterate over the mutiple Rx/Tx queues
hooked to the same interrupt lines.  And there's also an overhead
at HW level, as the controller needs to service all the 8 Tx rings
in a round robin manner.  The combined overhead shows up for multi
parallel Tx flows transmitted by the kernel stack, when the driver
usually starts returning NETDEV_TX_BUSY leading to NETDEV WATCHDOG
Tx timeout triggering if the Tx path is congested for too long.

As an alternative, this patch makes the driver support only one
Tx/Rx DMA ring per NAPI instance (per interrupt group or pair
of Tx/Rx interrupt lines) by default.  The simplified single queue
polling routine (gfar_poll_sq) will be the default napi poll routine
for the etsec2 devices too.  Some adjustments needed to be made to
link the Tx/Rx HW queues with each NAPI instance (2 in this case).
The gfar_poll_sq() is already successfully used by older SQ_SG_MODE
(single interrupt group) controllers.
This patch fixes Tx timeout triggering under heavy Tx traffic load
(i.e. iperf -c -P 8) for the "fsl,etsec2" (currently the only
MQ_MG_MODE devices).  There's also a significant memory footprint
reduction by supporting 2 Rx/Tx DMA rings (at most), instead of 8,
for these devices.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      71ff9e3d
    • C
      gianfar: Separate out the Tx interrupt handling (Tx NAPI) · aeb12c5e
      由 Claudiu Manoil 提交于 
      There are some concurrency issues on devices w/ 2 CPUs related
to the handling of Rx and Tx interrupts.  eTSEC has separate
interrupt lines for Rx and Tx but a single imask register
to mask these interrupts and a single NAPI instance to handle
both Rx and Tx work.  As a result, the Rx and Tx ISRs are
identical, both are invoking gfar_schedule_cleanup(), however
both handlers can be entered at the same time when the Rx and
Tx interrupts are taken by different CPUs.  In this case
spurrious interrupts (SPU) show up (in /proc/interrupts)
indicating a concurrency issue.  Also, Tx overruns followed
by Tx timeout have been observed under heavy Tx traffic load.

To address these issues, the schedule cleanup ISR part has
been changed to handle the Rx and Tx interrupts independently.
The patch adds a separate NAPI poll routine for Tx cleanup to
be triggerred independently by the Tx confirmation interrupts
only.  Existing poll functions are modified to handle only
the Rx path processing.  The Tx poll routine does not need a
budget, since Tx processing doesn't consume NAPI budget, and
hence it is registered with minimum NAPI weight.
NAPI scheduling does not require locking since there are
different NAPI instances between the Rx and Tx confirmation
paths now.
So, the patch fixes the occurence of spurrious Rx/Tx interrupts.
Tx overruns also occur less frequently now.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      aeb12c5e
  7. 08 3月, 2014 15 次提交
  9. 07 3月, 2014 2 次提交