The TS-4800 GPIO driver provide support for the GPIOs available
on the Technologic Sytems board FPGA. It allows to set
direction and read/write states.

It uses the generic gpio driver.
Signed-off-by: NJulien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Use irq_data_get_chip_type() instead of container_of().
Signed-off-by: NGeliang Tang <geliangtang@163.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NSantosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The gpio-mpc8xxx.c should can support qoriq and
Layerscape platforms.
Signed-off-by: NLiu Gang <Gang.Liu@nxp.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add F81866 GPIO supports

Fintek F81866 is a SuperIO. It contains HWMON/GPIO/Serial Ports.
and it has totally 72(9x8 sets) gpio pins.

Here is the PDF spec:
http://www.alldatasheet.com/datasheet-pdf/pdf/459085/FINTEK/F81866AD-I.html

The control method is the same with F7188x, but we should care the address
of GPIO8x.

GPIO address is below:
    GPIO0x based: 0xf0
    GPIO1x based: 0xe0
    GPIO2x based: 0xd0
    GPIO3x based: 0xc0
    GPIO4x based: 0xb0
    GPIO5x based: 0xa0
    GPIO6x based: 0x90
    GPIO7x based: 0x80
    GPIO8x based: 0x88 <-- not 0x70.
Signed-off-by: NPeter Hung <hpeter+linux_kernel@gmail.com>
Acked-by: NSimon Guinot <simon.guinot@sequanux.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The ACCES 104-DIO-48E device provides 48 lines digital I/O via two
Programmable Peripheral Interface (PPI) chips of type 82C55. Bit C3 at
each 24-bit Group can be used as an external interrupt, triggered by a
rising edge.

This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the dio_48e_base module parameter. The interrupt line number for the
device may be configured via the dio_48e_irq module parameter.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The WinSystems WS16C48 device provides 48 lines of digital I/O. In
addition, the first 24 lines may be used for interrupt-handled edge
detection; rising edge detection and falling edge detection are
supported.

This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the ws16c48_base module parameter. The interrupt line number for the
device may be configured via the ws16c48_irq module parameter.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The ACCES 104-IDI-48 can differentiate between its own and other
devices' interrupt requests. Therefore, IRQ sharing is possible and
should be permitted.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In some situations the gpio_list order is not correct.
As a consequence gpiochip_find_base returns the same
base number twice. This happens when a first ship is added
with manual base number, then other ships are added using
automatic base number.

To prevent this behaviour, this patch add the new chip after
the last element of the gpio list.
Signed-off-by: NJulien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit 709d71a1 ("gpio: mpc8xxx: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). However, the data
pointer is not yet set by the time the save_regs function is called.

Fixes: 709d71a1 ("gpio: mpc8xxx: use gpiochip data pointer")
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit 6aa7dbfa ("gpio: mm-lantiq: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). However, the data
pointer is not yet set by the time the save_regs function is called.

Fixes: 6aa7dbfa ("gpio: mm-lantiq: use gpiochip data pointer")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The CS47L24 and WM1831 codecs only have two GPIO lines, but are
otherwise similar to the WM8280.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

BMIPS_GENERIC (arch/mips/bmips) is the Kconfig symbol associated with
Broadcom MIPS-based STB chips. Since this driver is perfectly usable on
these platforms as well, allow using it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NGregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Broadcom MIPS-based STB chips endianness is configured by boot strap,
which also reverses all bus endianness (i.e., big-endian CPU + big
endian bus ==> native endian I/O).

Other architectures (e.g., ARM) either do not support big endian, or
else leave I/O in little endian mode.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NGregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

A cleanup patch replaced bgpio_chip with gpio_chip but missed
two references to the bgpio_chip:

drivers/gpio/gpio-moxart.c:60:19: error: use of undeclared identifier 'bgc'; did you mean 'gc'?
        gc->bgpio_data = bgc->read_reg(bgc->reg_set);
drivers/gpio/gpio-moxart.c:35:20: note: 'gc' declared here
drivers/gpio/gpio-moxart.c:60:33: error: use of undeclared identifier 'bgc'; did you mean 'gc'?
        gc->bgpio_data = bgc->read_reg(bgc->reg_set);

This adds the missing change.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 0f4630f3 ("gpio: generic: factor into gpio_chip struct")
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit 097d88e9 ("gpio: xilinx: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). Unfortunately, the
data pointer is not yet set by the time xgpio_save_regs() is called,
causing a system hang.

Fixes: 097d88e9 ("gpio: xilinx: use gpiochip data pointer")
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The double negation is costly and can be avoided by shifting the
register value before masking the requested bit.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We are not relying on container_of() now that we have
gpiochip_get_data().
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

For completion, sweep the floor from all gpiochip_add() usage so
we can remove that function and get rid of the function wrapper
gpiochip_add().
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Jun Nie <jun.nie@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Feng Kan <fkan@apm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: patches@opensource.wolfsonmicro.com
Cc: Mark Brown <broonie@kernel.org>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: patches@opensource.wolfsonmicro.com
Cc: Mark Brown <broonie@kernel.org>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: patches@opensource.wolfsonmicro.com
Cc: Mark Brown <broonie@kernel.org>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Roger Quadros <rogerq@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Cc: Margarita Olaya <magi@slimlogic.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-By: NRhyland Klein <rklein@nvidia.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>