提交 · 502f769662978a2fe99d0caed5e53e3006107381 · openeuler / Kernel

23 6月, 2013 1 次提交

Bluetooth: Add missing reset_resume dev_pm_ops · 502f7696

由 Shuah Khan 提交于 5月 21, 2013

Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().

[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

502f7696

14 6月, 2013 3 次提交

Bluetooth: btmrvl: fix error return code in btmrvl_sdio_card_to_host() · 6ea81c41

由 Wei Yongjun 提交于 6月 05, 2013

Fix to return -ENOMEM in the skb alloc error handling case
instead of 0, as done elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

6ea81c41

Bluetooth: Add support for Mediatek Bluetooth device [0e8d:763f] · 178c059e

由 Cho, Yu-Chen 提交于 6月 04, 2013

This patch adds support for Mediatek Bluetooth device

T:  Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0e8d ProdID=763f Rev= 1.00
S:  Manufacturer=MediaTek
S:  Product=BT
S:  SerialNumber=1.0
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=450mA
A:  FirstIf#= 0 IfCount= 2 Cls=ff(vend.) Sub=ff Prot=ff
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
Signed-off-by: NCho, Yu-Chen <acho@suse.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

178c059e

Bluetooth: btmrvl: fix thread stopping race · ea05fea9

由 Daniel Drake 提交于 6月 11, 2013

There is currently a race condition in the btmrvl_remove_card() which
is causing hangs on suspend for OLPC. When the race occurs,
kthread_stop() never returns.

The problem is that btmrvl_service_main_thread() calls kthread_should_stop()
and then does a fair number of things before restarting the loop and
sleeping.

If the thread gets stopped after kthread_should_stop() is checked, but
before the sleep happens, the thread will go to sleep and won't necessarily
be woken up.

Move the kthread_should_stop() check into a race-free place.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ea05fea9

12 6月, 2013 1 次提交

Bluetooth: btmrvl: support Marvell Bluetooth device SD8897 · 22f2efed

由 Bing Zhao 提交于 5月 13, 2013

The register offsets have been changed in SD8897 and newer chips.
Define a new btmrvl_sdio_card_reg map for SD88xx.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

22f2efed

24 4月, 2013 4 次提交

Bluetooth: btmrvl: report error if verify_fw_download times out · 69676b1c

由 Andreas Fenkart 提交于 4月 22, 2013

FW does the synchronization of the different modules during init.
It will report different modules, that it is ready at different times.
The fw download 'winner' will be reported fw ready first. Without this
patch, btmrvl was already continuing before the FW told it too. Probably
on behalf of the 'winner' which then never sees FW ready and times out.
Signed-off-by: NAndreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

69676b1c

Bluetooth: btmrvl: release lock while waiting for fw download complete · c1c999e2

由 Andreas Fenkart 提交于 4月 22, 2013

If not winner, driver must release the sdio host lock, so the fw
download can progress. While holding the lock fw download is stalled
and the following error is produced:

[  235.746015] Bluetooth: FW failed to be active in time!
[  235.752799] Bluetooth: Downloading firmware failed!
Signed-off-by: NAndreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

c1c999e2

Bluetooth: btmrvl: use native helpers for debugfs · 9da226c7

由 Andy Shevchenko 提交于 4月 23, 2013

Clean up the code by using native debugfs helpers, instead of implementing
them ourselves:

	debugfs_create_u8()
	debugfs_create_x16()
	debugfs_create_file()
	debugfs_remove_recursive()
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

9da226c7

Bluetooth: Add support for Intel Bluetooth device [8087:07dc] · dffd30ee

由 Tedd Ho-Jeong An 提交于 4月 19, 2013

This patch adds support for Intel Bluetooth device by adding
btusb_setup_intel() routine that update the device with ROM patch.

T:  Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=07dc Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

dffd30ee

19 4月, 2013 1 次提交

Bluetooth: remove unneeded var initialization in btmrvl · faff7f74

由 Gustavo Padovan 提交于 4月 18, 2013

There is no need to init ret to zero in  btmrvl_sdio_download_fw().
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

faff7f74

12 4月, 2013 1 次提交

Bluetooth: Use separate function for BCM92035 vendor setup · 9f8f962c

由 Marcel Holtmann 提交于 4月 10, 2013

Trying to squeeze every single vendor setup routine into the same function
and have it assigned all the time is actually a bad idea. Especially since
the core can handle the absence of a setup routine perfectly fine.

To make this a lot simpler for future additions of vendor setup code,
split the BCM92035 setup into its own function and only assign it when
this specific device has been detected.

Doing it like this has the nice side benefit that we do not have to keep
a copy of the driver_info around.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

9f8f962c

05 4月, 2013 1 次提交

Bluetooth: Convert BCM92035 support to driver setup callback · 93600997

由 Marcel Holtmann 提交于 11月 12, 2012

With the early init stage during setup, this quirk can be simplified
and kept fully inside the driver.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

93600997

04 4月, 2013 4 次提交

Bluetooth: Remove trivial white space · 1687dfc3

由 Chan-yeol Park 提交于 4月 02, 2013

This patch removes redundant whitespace from the HCI ldisc driver.
Signed-off-by: NChan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

1687dfc3

Bluetooth: Fix possible NULL dereference in hci_uart_tty_receive · 788f0923

由 Chan-yeol Park 提交于 4月 02, 2013

This patch adds a NULL check for the HCI UART ldisc driver because some
of HCI UART drivers allow hci_uart_tty_receive function to be called
even though the HCI device hasn't been registered yet.
Signed-off-by: NChan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

788f0923

Bluetooth: Fix H4 crash from incoming UART packets · c2578202

由 Chan-yeol Park 提交于 4月 02, 2013

This patch adds a check HCI_UART_REGISTERED before reading UART data in
the HCI UART H4 driver. UART data could arrive when inside the
hci_uart_tty_ioctl function after calling test_and_set_bit for
HCI_UART_PROTO_SET but before the hci_uart_set_proto function has
returned.

Backtrace:
[<c05f27ec>] (hci_recv_stream_fragment+0x0/0x74) from [<c04126f4>] (h4_recv+0x18/0x40)
 r7:eb1d4d1c r6:eb7683b0 r5:eae8e800 r4:0000000c
[<c04126dc>] (h4_recv+0x0/0x40) from [<c0411870>] (hci_uart_tty_receive+0x6c/0x94)
 r5:eae8e800 r4:eb768380
[<c0411804>] (hci_uart_tty_receive+0x0/0x94) from [<c027be88>] (flush_to_ldisc+0x16c/0x17c)
 r6:eae8e8d8 r5:eae8e800 r4:eae8e8c8
[<c027bd1c>] (flush_to_ldisc+0x0/0x17c) from [<c0050ae8>] (process_one_work+0x144/0x4d4)
[<c00509a4>] (process_one_work+0x0/0x4d4) from [<c0051208>] (worker_thread+0x180/0x370)
[<c0051088>] (worker_thread+0x0/0x370) from [<c005617c>] (kthread+0x90/0x9c)
[<c00560ec>] (kthread+0x0/0x9c) from [<c003a3a0>] (do_exit+0x0/0x7ec)
Signed-off-by: NChan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

c2578202

Bluetooth: Add support for Foxconn/Hon Hai [0489:e04d] · 0fc110f4

由 Noguchi Kazutosi 提交于 3月 24, 2013

Add support for the AR3012 chip.

T:  Bus=01 Lev=02 Prnt=02 Port=05 Cnt=03 Dev#= 21 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e04d Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NNoguchi Kazutosi <linux@scaltinof.net>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

0fc110f4

19 3月, 2013 1 次提交

Bluetooth: Add support for Dell[QCA 0cf3:817a] · ebaf5795

由 Ming Lei 提交于 3月 18, 2013

Add support for the AR9462 chip

T:  Bus=03 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#=  5 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=817a Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Cc: <stable@vger.kernel.org>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

ebaf5795

16 3月, 2013 3 次提交

drivers/bluetooth: use module_pcmcia_driver() in pcmcia drivers · e0c005f4

由 H Hartley Sweeten 提交于 3月 06, 2013

Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

e0c005f4

bluetooth: btmrvl_sdio: look for sd8688 firmware in proper location · 77189df4

由 Lubomir Rintel 提交于 3月 13, 2013

The firmware images are shared with libertas_sdio WiFi chip and used to be
in libertas/ subtree in linux-firmware. As btmrvl_sdio used to look into
the linux-firmware root, it ended up being unsuccessful. Since the
firmware files are not specific to the libertas hardware, they're being
moved into mrvl/ now.
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

77189df4

Bluetooth: Add support for Dell[QCA 0cf3:0036] · d66629c1

由 Ming Lei 提交于 3月 15, 2013

Add support for the AR9462 chip

T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=0036 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Cc: <stable@vger.kernel.org>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

d66629c1

12 3月, 2013 1 次提交

Bluetooth: Device 0cf3:3008 should map AR 3012 · 94a32d10

由 Sunguk Lee 提交于 3月 12, 2013

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=3008 Rev= 0.01
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NSunguk Lee <d3m3vilurr@gmail.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

94a32d10

21 2月, 2013 1 次提交

Bluetooth: Add support for atheros 04ca:3004 device to ath3k · 3f63c340

由 Josh Boyer 提交于 2月 19, 2013

Yet another version of the atheros bluetooth chipset

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3004 Rev=00.01
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

This resolves https://bugzilla.redhat.com/show_bug.cgi?id=844750

Reported-by: niktr@mail.ru
Signed-off-by: NJosh Boyer <jwboyer@redhat.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

3f63c340

19 1月, 2013 1 次提交

tty: Added a CONFIG_TTY option to allow removal of TTY · 4f73bc4d

由 Joe Millenbach 提交于 1月 17, 2013

The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.

The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer.  Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.

bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY.  The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.

add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function                                     old     new   delta
chr_dev_init                                 166     170      +4
allow_signal                                  80      82      +2
static.__warned                              143     142      -1
disallow_signal                               63      62      -1
__set_special_pids                            95      94      -1
unregister_console                           126     121      -5
start_kernel                                 546     541      -5
register_console                             593     588      -5
copy_from_user                                45      40      -5
sys_setsid                                   128     120      -8
sys_vhangup                                   32      19     -13
do_exit                                     1543    1526     -17
bitmap_zero                                   60      40     -20
arch_local_irq_save                          137     117     -20
release_task                                 674     652     -22
static.spin_unlock_irqrestore                308     260     -48
Signed-off-by: NJoe Millenbach <jmillenbach@gmail.com>
Reviewed-by: NJamey Sharp <jamey@minilop.net>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

4f73bc4d

10 1月, 2013 5 次提交

Bluetooth device 04ca:3008 should use ath3k · f4d6f7dc

由 Sergio Cambra 提交于 1月 10, 2013

Output of /sys/kernel/debug/usb/devices
T:  Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  6 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3008 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NSergio Cambra <sergio@programatica.es>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

f4d6f7dc

Bluetooth: Add support for Foxconn / Hon Hai [0489:e056] · 2582d529

由 AceLan Kao 提交于 1月 03, 2013

Add support for the AR9462 chip

T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e056 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

2582d529

Bluetooth: Add support for Foxconn / Hon Hai [0489:e04e] · 3a61eda8

由 AceLan Kao 提交于 1月 03, 2013

Add support for the AR9462 chip

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e04e Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

3a61eda8

Bluetooth: Add support for GC-WB300D PCIe [04ca:3006] to ath3k. · 2c262b2a

由 Daniel Schaal 提交于 12月 29, 2012

T:  Bus=02 Lev=02 Prnt=02 Port=06 Cnt=01 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3006 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NDaniel Schaal <farbing@web.de>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

2c262b2a

Bluetooth: Add support for IMC Networks [13d3:3393] · eed307e2

由 AceLan Kao 提交于 12月 11, 2012

Add support for the AR9462 chip

T:  Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3393 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

eed307e2

09 1月, 2013 1 次提交

treewide: Fix typo in various drivers · 8a168ca7

由 Masanari Iida 提交于 12月 29, 2012

Correct spelling typo in printk within various drivers.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

8a168ca7

20 11月, 2012 1 次提交

Bluetooth: Add support for BCM20702A0 [0b05, 17b5] · 1ee3ff61

由 Jeff Cook 提交于 11月 09, 2012

Vendor-specific ID for BCM20702A0.
Support for bluetooth over Asus Wi-Fi GO!, included with Asus P8Z77-V
Deluxe.

T:  Bus=07 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0b05 ProdID=17b5 Rev=01.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=94DBC98AC113
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Cc: stable@vger.kernel.org
Signed-off-by: NJeff Cook <jeff@deserettechnology.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

1ee3ff61

09 11月, 2012 1 次提交

Bluetooth: ath3k: Add support for VAIO VPCEH [0489:e027] · acd94544

由 Marcos Chaparro 提交于 11月 06, 2012

Added Atheros AR3011 internal bluetooth device found in Sony VAIO VPCEH to the
devices list.
Before this, the bluetooth module was identified as an Foxconn / Hai bluetooth
device [0489:e027], now it claims to be an AtherosAR3011 Bluetooth
[0cf3:3005].

T:  Bus=01 Lev=02 Prnt=02 Port=04 Cnt=02 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e027 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NMarcos Chaparro <marcos@mrkindustries.com.ar>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

acd94544

23 10月, 2012 1 次提交

TTY: hci_ldisc, remove invalid check in open · f327b340

由 Jiri Slaby 提交于 10月 18, 2012

hci_ldisc's open checks if tty_struct->disc_data is set. And if so it
returns with an error. But nothing ensures disc_data to be NULL. And
since ld->ops->open shall be called only once, we do not need the
check at all. So remove it.

Note that this is not an issue now, but n_tty will start using the
disc_data pointer and this invalid 'if' would trigger then rendering
TTYs over BT unusable.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

f327b340

11 10月, 2012 1 次提交

Bluetooth: btmrv: Use %*ph specifier instead of print_hex_dump_bytes · 78c1b8e8

由 Andrei Emeltchenko 提交于 10月 10, 2012

Use standard print specifier and remove print_hex_dump_bytes call.
Makes output more sensible:

...
[18809.401218] 00000000: 0b 00 00 fe 5b fc 01 f2 00 00 00    ....[......
...

would be changed to

...
[18809.401218] Bluetooth: hex: 0b 00 00 fe 5b fc 01 f2 00 00 00
...
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

78c1b8e8

28 9月, 2012 3 次提交

Bluetooth: btmrvl: Fix skb buffer overflow · 9cb23dd4

由 Andrei Emeltchenko 提交于 9月 28, 2012

Add extra check to avoid skb buffer overflow. Fixes crash below:

 [  101.030427] ------------[ cut here ]------------
 [  101.030459] kernel BUG at net/core/skbuff.c:127!
 [  101.030486] invalid opcode: 0000 [#1] SMP
...
 [  101.030806] Pid: 2010, comm: btmrvl_main_ser Not tainted 3.5.0+ #80 Laptop
 [  101.030859] EIP: 0060:[<c14f2ba9>] EFLAGS: 00010282 CPU: 0
 [  101.030894] EIP is at skb_put+0x99/0xa0
 [  101.030919] EAX: 00000080 EBX: f129380b ECX: ef923540 EDX: 00000001
 [  101.030956] ESI: f00a4000 EDI: 00001003 EBP: ed4a5efc ESP: ed4a5ecc
 [  101.030992]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
 [  101.031024] CR0: 8005003b CR2: 08fca014 CR3: 30960000 CR4: 000407f0
 [  101.031062] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
 [  101.031100] DR6: ffff0ff0 DR7: 00000400
 [  101.031125] Process btmrvl_main_ser (pid: 2010, ti=ed4a4000 task=ef923540 task.ti=ed4a4000)
 [  101.031174] Stack:
 [  101.031188]  c18126f8 c1651938 f853f8d2 00001003 00001003 f1292800 f1292808 f129380b
 [  101.031250]  f1292940 f00a4000 eddb1280 efc0f9c0 ed4a5f44 f853f8d2 00000040 00000000
 [  101.031312]  ef923540 c15ee096 ef923540 eddb12d4 00000004 f00a4000 00000040 00000000
 [  101.031376] Call Trace:
 [  101.031396]  [<f853f8d2>] ? btmrvl_sdio_process_int_status+0x272/0x3d0 [btmrvl_sdio]
 [  101.031444]  [<f853f8d2>] btmrvl_sdio_process_int_status+0x272/0x3d0 [btmrvl_sdio]
 [  101.031488]  [<c15ee096>] ? _raw_spin_unlock_irqrestore+0x36/0x70
 [  101.031526]  [<f85a46e4>] btmrvl_service_main_thread+0x244/0x300 [btmrvl]
 [  101.031568]  [<f853fb50>] ? btmrvl_sdio_poll_card_status.isra.6.constprop.7+0x90/0x90 [btmrvl_sdio]
 [  101.031619]  [<c107eda0>] ? try_to_wake_up+0x270/0x270
 [  101.031648]  [<f85a44a0>] ? btmrvl_process_event+0x3b0/0x3b0 [btmrvl]
 [  101.031686]  [<c106d19d>] kthread+0x7d/0x90
 [  101.031713]  [<c106d120>] ? flush_kthread_work+0x150/0x150
 [  101.031745]  [<c15f5a82>] kernel_thread_helper+0x6/0x10
...
 [  101.032008] EIP: [<c14f2ba9>] skb_put+0x99/0xa0 SS:ESP 0068:ed4a5ecc
 [  101.056125] ---[ end trace a0bd01d1a9a796c8 ]---
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

9cb23dd4

Bluetooth: btmrvl: Use DIV_ROUND_UP macro · e678bad5

由 Andrei Emeltchenko 提交于 9月 28, 2012

The kernel.h macro DIV_ROUND_UP performs the computation
(((n) + (d) - 1) / (d))
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

e678bad5

Bluetooth: btmrvl: Correct num_block name · 42632805

由 Andrei Emeltchenko 提交于 9月 28, 2012

Make code readable by correcting name from buf_block_len to num_blocks
since it represent number of blocks; NOT a length of a block buffer.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

42632805

19 9月, 2012 4 次提交

Bluetooth: Add support for BCM20702A0 [04ca, 2003] · 0c1abbd1

由 Jaroslav Resler 提交于 9月 11, 2012

Add another vendor specific ID for BCM20702A0.

output of usb-devices:
T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=2003 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=446D57861623
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NCho, Yu-Chen <acho@suse.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

0c1abbd1

Bluetooth: Add USB_VENDOR_AND_INTERFACE_INFO() for Broadcom/Foxconn · ee66401b

由 Gustavo Padovan 提交于 8月 15, 2012

Foxconn devices has a vendor specific class of device, we will match them
differently now.

Cc: stable@vger.kernel.org
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

ee66401b

Bluetooth: btuart_cs.c: removes unnecessary semicolon · 5ad77795

由 Peter Senna Tschudin 提交于 9月 07, 2012

removes unnecessary semicolon

Found by Coccinelle: http://coccinelle.lip6.fr/Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

5ad77795

Bluetooth: hci_vhci.c: removes unnecessary semicolon · 2c24d454

由 Peter Senna Tschudin 提交于 9月 07, 2012

removes unnecessary semicolon

2c24d454

openeuler / Kernel 1 年多 前同步成功

openeuler / Kernel
1 年多前同步成功