Tell the PCIe host core when the wifi is activated.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enables or disables power saving on the PCIe bus when the wifi is
in operation or not.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is not called any more, do not export it.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

replace the calls to bcma_core_pci_extend_L1timer() by calls to the
newly introduced bcma_core_pci_ip() and bcma_core_pci_down()
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wifi driver should tell the PCIe core that it is now in operation
so that some workarounds can be applied and the power state is changed.
This should replace the call to bcma_core_pci_extend_L1timer by the
brcmsmac driver.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This PCIe controller does not support a max read request size above 128
bytes. The sold card I tested this controller with used 128 as default
value, but some new routers are sold with BCM4331 chips, which have a
default max read request size of 512. This device fails at the first
DMA reqeust whch is bigger than 126 bytes.

This patch changes the max read request size to 128 for every device on
the PCIe link.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The values written into the BCN_OFFSET[01] registers are
hardcoded in the rt2800_init_register function.

Add a macro and a helper function to derive these values
directly from the base address of a given beacon, and use
the new function instead of the hardcoded numbers.

The patch contains no functional changes. The programmed
register values are the same before and after the patch.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The HW_BEACON_BASE() macro returns the base address
of a given beacon, however the returned values are
not usable on all chipsets. On devices which have
selectable shared memory parts, some beacon may be
located in the high part of the shared memory.

Instead of extending the already complicated macro,
add a new helper function and use that to get the
base address of a given beacon.

The actual patch contains no functional changes, the
helper function will be extended in a further patch
to handle different chipsets' requirements.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch completes the changes needed for supporting the
iPA variant cards of the BCM4313 wireless chipset.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When changing channels the TSSI based power control needs to be
reinitialized.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A number of additional phy registers needs to be programmed when
using TSSI-based power control.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rework the code path in lcnphy tbl_init() for switch control
table programming. This also takes the iPA BT-combo card into
account.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For lcnphy revision 1 or when hardware supports i/q calibration the
function wlc_lcnphy_set_txpwr_by_index() was called twice.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The baseband multiplier must be zero during TSSI idle estimation
and restored afterwards.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The gain level control for the test tone has been changed. This
calbration test tone is used to determine the i/q compensation.
The i/q calibration routine has been reworked to accomodate this.

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the transmit gain table for bcm4313 chip family.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For debug purposes it is good to have the phy and radio information
available in the log. Only logged when driver is built when BRCMDBG
or BRCM_TRACING kconfig are set.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch converts all sizeof(x)/sizeof(x[0]) instances to
ARRAY_SIZE macro in phytbl_lcn.c. The patch was made using
spatch with ARRAY_SIZE.cocci (see [1]).

[1] https://github.com/coccinelle/coccinelle/tree/master/demos/janitorings

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function wlc_lcnphy_load_tx_gain_table() has a target PA
gain specified for the iPA variant of the bcm4313. This gain
value is reduced to avoid PA distortion. The if-statement is
removed because it was rather redundant in the first place.
Please note that this patch does not provide full iPA support.

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleaning up some code fragments reducing indentation and uncluttering
some lines. Apart from whitespace there are no actual code changes
made.

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a AR9485/WB225 based card.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bug 60747 - 1286:2044 [Microsoft Surface Pro]
    Marvell 88W8797 wifi show 3 interface under network
https://bugzilla.kernel.org/show_bug.cgi?id=60747

This issue was also reported previously by OLPC and some folks from
the community.

There are 3 network interfaces with different types being created
when mwifiex driver is loaded:

1. mlan0 (infra. STA)
2. uap0 (AP)
3. p2p0 (P2P_CLIENT)

The Network Manager attempts to use all 3 interfaces above without
filtering the managed interface type. As the result, 3 identical
interfaces are displayed under network manager. If user happens to
click on an entry under which its interface is uap0 or p2p0, the
association will fail.

Work around it by removing the creation of AP and P2P interfaces
at driver loading time. These interfaces can be added with 'iw' or
other applications manually when they are needed.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This improves RX diversity and performance for AR9485.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Along with other chipsets, the Ralink driver uses the
frequency adjustment code for RF3053 as well. Remove
the bogus place-holder comment from the RF3053 specific
channel configuration function and call the frequency
adjustment function instead

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RT3593_ChipSwitchChannel function in chips/rt3593.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the rt2800_adjust_freq_offset function before
the channel configuration functions to make it usable
from those without a forward declaration.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver, the RFCSR17 register can't be programmed in
one step on devices which are using the frequency
offset adjustment code.

Update the code to use step-by-step adjustment.

Reference:
  RT30xxWriteRFRegister function in common/rt_rf.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the Ralink driver, there is an MCU
command which can be used to send the frequency
offset value directly to the USB device without
going through the RFCSR writing sequence.

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't write the new value into the register if it is
the same as the old value to avoid unncessary USB bus
traffic with USB devices. The change also saves a few
cycle on MMIO based devices.

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current code in the 'rt2800_adjust_freq_offset'
function limits the device specific frequency offset
value to FREQ_BOUND but ignores the fact that the
uppermost bit is not part of the frequency offset
value. As the result, the driver always uses the
FREQ_BOUND value if the uppermost bit is set.

Update the code to use the correct source value
for calculating the boundary.

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of precomputing the beacon base in
each caller, pass the beacon index to the
'rt2800_clear_beacon_register' function
and compute the beacon base in there.

This allows to simplify the caller functions
a bit.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The name of the HW_BEACON_OFFSET macro is a
bit confusing. It returns with one of the
HW_BEACON_BASE* values, so rename the macro
to HW_BEACON_BASE to reflect that.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When initiating a transparent eSCO connection, make use of T2 settings
at first try. T2 is the recommended settings from HFP 1.6 WideBand
Speech. Upon connection failure, try T1 settings.

When CVSD is requested and eSCO is supported, try to establish eSCO
connection using S3 settings. If it fails, fallback in sequence to S2,
S1, D1, D0 settings.

To know which setting should be used, conn->attempt is used. It
indicates the currently ongoing SCO connection attempt and can be used
as the index for the fallback settings table.

These setting and the fallback order are described in Bluetooth HFP 1.6
specification p. 101.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Synchronous Connection Complete event can return error "Connection
Rejected due to Limited resources (0x10)".
Handling this error is required for SCO connection fallback. This error
happens when the server tried to accept the connection but failed to
negotiate settings.
This error code has been verified experimentally by sending a T2 request
to a T1 only SCO listener.

Client dump follows :

< HCI Command (0x01|0x0028) plen 17 [hci0] 3.696064
        Handle: 12
        Transmit bandwidth: 8000
        Receive bandwidth: 8000
        Max latency: 13
        Setting: 0x0003
        Retransmission effort: Optimize for link quality (0x02)
        Packet type: 0x0380
> HCI Event (0x0f) plen 4 [hci0] 3.697034
      Setup Synchronous Connection (0x01|0x0028) ncmd 1
        Status: Success (0x00)
> HCI Event (0x2c) plen 17 [hci0] 3.736059
        Status: Connection Rejected due to Limited Resources (0x0d)
        Handle: 0
        Address: xx:xx:xx:xx:xx:AB (OUI 70-F3-95)
        Link type: eSCO (0x02)
        Transmission interval: 0x0c
        Retransmission window: 0x06
        RX packet length: 60
        TX packet length: 60
        Air mode: Transparent (0x03)

Server dump follows :

> HCI Event (0x04) plen 10 [hci0] 4.741513
        Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
        Class: 0x620100
          Major class: Computer (desktop, notebook, PDA, organizers)
          Minor class: Uncategorized, code for device not assigned
          Networking (LAN, Ad hoc)
          Audio (Speaker, Microphone, Headset)
          Telephony (Cordless telephony, Modem, Headset)
        Link type: eSCO (0x02)
< HCI Command (0x01|0x0029) plen 21 [hci0] 4.743269
        Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
        Transmit bandwidth: 8000
        Receive bandwidth: 8000
        Max latency: 13
        Setting: 0x0003
        Retransmission effort: Optimize for link quality (0x02)
        Packet type: 0x03c1
> HCI Event (0x0f) plen 4 [hci0] 4.745517
      Accept Synchronous Connection (0x01|0x0029) ncmd 1
        Status: Success (0x00)
> HCI Event (0x2c) plen 17 [hci0] 4.749508
        Status: Connection Rejected due to Limited Resources (0x0d)
        Handle: 0
        Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
        Link type: eSCO (0x02)
        Transmission interval: 0x0c
        Retransmission window: 0x06
        RX packet length: 60
        TX packet length: 60
        Air mode: Transparent (0x03)
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Older Bluetooth devices may not support Setup Synchronous Connection or
SCO transparent data. This is indicated by the corresponding LMP feature
bits. It is not possible to know if the adapter support these features
before setting BT_VOICE option since the socket is not bound to an
adapter. An adapter can also be added after the socket is created. The
socket can be bound to an address before adapter is plugged in.

Thus, on a such adapters, if user request BT_VOICE_TRANSPARENT, outgoing
connections fail on connect() and returns -EOPNOTSUPP. Incoming
connections do not fail. However, they should only be allowed depending
on what was specified in Write_Voice_Settings command.

EOPNOTSUPP is choosen because connect() system call is failing after
selecting route but before any connection attempt.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch defines constants and macro for transparent data LMP
features. It refers to Bluetooth Core V4.0 specification, Part C, Chap
3.3 which defines LMP feature mask.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

In order to establish a transparent SCO connection, the correct settings
must be specified in the Setup Synchronous Connection request. For that,
a setting field is added to ACL connection data to set up the desired
parameters. The patch also removes usage of hdev->voice_setting in CVSD
connection and makes use of T2 parameters for transparent data.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When an incoming eSCO connection is requested, check the selected voice
setting and reply appropriately. Voice setting should have been
negotiated previously.  For example, in case of HFP, the codec is
negotiated using AT commands on the RFCOMM channel. This patch only
changes replies for socket with deferred setup enabled.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch defines constants for SCO airmode from SCO voice setting. It
refers to Bluetooth Core V4.0 specification, Part E, Chap 6.12 which
describe SCO voice setting format.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>