This ensures we won't add polling function to the table of polling technologies
for non-supported protocols.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

nfc_find_se() does not modify any list entry while iterating the list.
So use list_for_each_entry instead of list_for_each_entry_safe.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Calling init_completion() once is enough.
Then use reinit_completion() instead in __nci_request() and nci_spi_send().
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This fixes a memory leak issue that may occur if data sending fails in
initiator mode. The data_exch structure was not released in case of
error.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

There was a missing break making the digital stack configured for
ISO1443 target instead of ISO15693.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds support for ISO-DEP protocol over NFC-A rf technology. The
port100 already supports NFC-A and ATS request and response for type 4A
tags are handled at digital level. This patch adds NFC_PROTO_ISO14443
to the supported protocols and an entry for framing configuration which
is the same as NFC-A standard frame with CRC handling.
Signed-off-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When a type 4A target is activated, this change adds the ISO-DEP SoD
when sending frames and removes it when receiving responses. Chaining
is not supported so sent frames are rejected if they exceed remote FSC
bytes.
Signed-off-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds support for ATS request and response handling for type 4A tag
activation.
Signed-off-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The arrays for protocols and rf techs must define a number of entries
corresponding to their maximum possible index values.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

PN544 C3 firmwares already contain the command frames to be sent, but as
they may exceed the i2c maximum payload, we need to fragment them into
secure chunks and send them through the secure write command.
Signed-off-by: NArron Wang <arron.wang@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Different pn544 hardware variant may use different commands to download
new firmwares. The C2 does a regular firmware download while the C3 uses
a more secure protocol.
As a consequence we need to pass the hardware variant from the HCI SW
version command reply down to the pn544 i2c layer, in order to use the
right protocol at run time.
Signed-off-by: NArron Wang <arron.wang@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add ISO/IEC 15693 support by having netlink push the
1-byte DSFID and 8-byte UID tag information upstream.
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add support for ISO/IEC 15693 to the digital layer.  The code
currently uses single-slot anticollision only since the digital
layer infrastructure only supports one tag per adapter (making
it pointless to do 16-slot anticollision).

The code uses two new framing types:
'NFC_DIGITAL_FRAMING_ISO15693_INVENTORY' and
'NFC_DIGITAL_FRAMING_ISO15693_TVT'.  The former is used to
tell the driver to prepare for an Inventory command and the
ensuing anticollision sequence.  The latter is used to tell
the driver that the anticollision sequence is over and to
prepare for non-inventory commands.
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add the header definitions required by upcoming
patches that add support for ISO/IEC 15693.
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This has been removed in further work.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The dtim period sent to FW was 0 because the dtim period
was never set. This caused an incorrect dtim count to be sent in
beacons.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes problems seen with multiple softap clients and reconnecting
softap clients.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is more line with the names of the other members
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

3680 has a few registers on other addresses.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After fw caps exchange, print the FW's capabilities.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If wowlan if off mac80211 will stop / start the driver on suspend /
resume. This causes problems on resume since request_firmware is called
from start. Fix this by caching the nv.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On some wcnss firmwares the start command can take up to 300ms to
complete. Currently there is a 200ms timeout for SMD command to
complete which causes the start to fail.

Increase the timeout to 500ms. Also improve debug information
regarding SMD command completion time.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Response format is not in the canonical format.
  wcn36xx_smd_rsp_status_check cannot be used.

* Save the FW caps in wcn36xx struct for later use.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TI wl12xx/wl18xx cards support channel switch via a driver specific
switch_channel op while operating with channel contexts.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enabling beacon filtering before receving a beacon
might result in not having a beacon at all for the
current connected AP, which prevents the station
from entering power-save.

Replace the current approach (of starting beacon
filtering on init) and configure beacon filering
only after bss_conf->dtimper is set (which means
mac80211 already parsed a beacon).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dfs configuration command might take longer than
the current timeout. increase it to 5 seconds.
Signed-off-by: NYaniv Machani <yanivma@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Silently ignore repetitive scheduling of recovery work and commands
being passed to the bus when the HW is not available. This can happen
many times during recovery and slow it down. It also spams the kernel
logs.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each AP has its own global and broadcast links, so when
checking for active sta count (according to the active_link_count)
we must take them all into account.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 unsets the default wep key on disassoc.
The fw doesn't support this notification, so simply
ignore it.

The actual flow actually triggers fw recovery in some
cases, as mac80211 unsets the default key only after
disassoc, when wlvif->sta.hlid, resulting in invalid
hlid being passed to the fw.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

12xx chips allow only OFDM rates in AP mode for BT-Coex purposes. This
is no longer required in 18xx chips, starting with FW 8.6.0.0.8.

Update the min allowed FW version in 18xx to support this functionality.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stopping sched scan on interface removal (during recovery)
is no longer needed, as sched scanning is automatically
restarted by mac80211.
Signed-off-by: NBarak Bercovitz <barak@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Send EAPOL frames with voice priority by setting (the new)
TX_HW_ATTR_EAPOL_FRAME bit in tx attribute.

Sending EAPOL with voice priority fixes re-key
timeout issues during heavy traffic.
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bump the min wl18xx fw version to 8.8.0.0.13

This fw is not backward compatible with older
firmware (due to api changes), so use bump
the firmware name as well.

Some modifications were done to the driver-fw api
in order to support multiple APs.

Additionally, some of the consts (such as max stations,
max links and max RX BA sessions) were changed.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each hw supports a different iface combinations.
Define the supported combinations in each driver,
and save it in wl->iface_combinations.

Since each driver defines its own combinations now,
it can also define its max supported channels, so
we no longer need to save and set it explicitly
in wlcore.

Update wl18xx interface combinations to allow
multiple APs.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each hw supports a different max stations (connected to the
same ap). add a new wl->max_ap_stations and use it instead
of the current common AP_MAX_STATIONS.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upcoming fw versions will have different max links support
(according to the hw). Get ready for it by configuring
wl->num_links per-hw, instead of using the const WL12XX_MAX_LINKS.

However, continue using WLCORE_MAX_LINKS in order to simplify
structs declarations (we use it in multiple bitmaps, and converting
them to dynamic arrays is just cumbersome).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of splitting the fw_status into 2 and using some
complex calculations, read the fw status and let each low-level
driver (wl12xx/wl18xx) convert it into a common struct.

This is required for the upcoming fw api changes, which
break the current logic anyway.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>