The imx5 pm code needs to access CCM registers.  Let's remove the use
of CCM static mapping in pm code by reusing the dynamic mapping created
in clock code.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Replace the static mapping of DPLL block with dynamic mapping by
calling ioremap().  Ideally, this should be done by calling of_iomap(),
so that the physical address of DPLL can also be retrieved from device
tree.  But unfortunately, DPLL blocks are not defined in DT in the first
place.  So to maintain the compatibility of existing DTB, we use
ioremap() with physical address defines in the code.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Replace the static mapping of CCM block with dynamic mapping and
retrieve CCM base address from device tree.  Though it's not nice to
encode the variable ccm_base in macros, it helps to avoid a massive
churn on the code.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Most of the macros in crm-regs-imx5.h are used nowhere.  Let's move the
needed ones into the C files, and remove the header.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Since i.MX51 supports DT only, it's more appropriate to call
mxc_timer_init_dt() than mxc_timer_init() to initialize timer.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The function mx5_clocks_common_init() was created with a number of
arguments to pass oscillator clock rate in non-DT boot.  Since i.MX5
is DT only platform, the arguments can be dropped, and the clock rate
can just be retrieved from device tree.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Since i.MX51 becomes a DT only platform, we can make mx51_clocks_init()
a DT call and save function mx51_clocks_init_dt() now.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NGilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

CODA7 clock lookups are now defined in the device tree.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

As the i.MX pwm driver is devicetree only, remove the platform
support for this device.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

ldb_di0_gate is registerd with the clk index of IMX5_CLK_LDB_DI1_GATE,
thus the DI0 interface will be turned off inadvertently during boot.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch sets the parent of CAN peripheral clock (a.k.a. CPI clock) to the
lp_apm clock, which has a rate of 24 MHz.

In the CAN world a base clock with multiple of 8 MHz is suited best for all CIA
recommented bit rates. Without this patch the CAN peripheral clock on i.MX53
has a rate of 66.666 MHz which produces quite large bit rate errors.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

According to the i.MX50 Rev. 1 and i.MX53 Rev. 2.1 datasheet the lp_apm_sel is
bit 10 in the CCM_CCSR register not bit 9. On the i.MX51 it's bit 9.

This patch fixes this issue.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add SATA PHY clock which are derived from the USB PHY1 clock. Note that this
patch derives the SATA PHY clock from USB PHY1 clock gate so that the SATA
driver can ungate both the SATA PHY clock and USB PHY1 clock for the SATA to
work correctly.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linux-IDE <linux-ide@vger.kernel.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Use clock defines in order to make devicetrees more
human readable.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Patch adds missing Security Accelerator (SAHARA) clock for i.MX5x CPUs.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add code to support the specific clock tree of the Freescale IMX50 SoC.
It can use much of the common IMX51/IMX53 clocking code.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

As mx53 is a dt-only SoC, we should retrieve the gpt base address and irq
from the device tree, instead of using the old MX53_IO_ADDRESS method.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

With arch/arm calling of_clk_init(NULL) from time_init(), we can now
remove custom .init_time hooks.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>

Currently all clkdev registration use "cpufreq-cpu0.0" as dev_id
for cpu clock which refers to virtual platform device. It needs to
be "cpu0" instead which is actual cpu0 device id.

This patch changes the dev_id from "cpufreq-cpu0.0" to "cpu0".
Reported-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NSudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Since commit beb2d1c1 (ARM i.MX5: Add S/PDIF clocks), the following clock
error appears on mx51:

TrustZone Interrupt Controller (TZIC) initialized
i.MX51 clk 180: register failed with -17
i.MX5 clk 180: register failed with -17
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
CPU identified as i.MX51, silicon rev 3.0
...

Clock 180 corresponds to 'spdif1_podf' and this clock is getting registered
twice.

Fix it, by properly registering the 'spdif1_pred' clock, which should not
reference 'spdif1_podf'.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add missing ocram gate clock for imx53 and also represent it in device
tree ocram node.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

With device tree clk lookup support in place, we can move audio codec
clk lookup for ssi_ext1 into device tree now, so that imx53_qsb_init()
can be saved.

Since ssi_ext2 lookup is used nowhere, it gets removed together with
ssi_ext1 lookup from clk driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds the S/PDIF clocks for i.MX51 and i.MX53. Tested on i.MX53.
The i.MX51 has a second set of spdif_root clock dividers, and on i.MX53
there is an additional input to the spdif_xtal mux.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Currently clock providers defined in the DT are not registered
on i.MX5 platforms since of_clk_init() is not called.

This is not a problem for the SOC's own clocks, which are registered
in code,  but prevents the DT being used to define clocks for external
hardware.

Fix this by calling of_clk_init() and actually using the DT to obtain
the 4 SOC fixed clocks.
These are already defined in the DT but were previously just used to
manually obtain the rate.

Fall back to the old scheme for non DT platforms.

Since the same method may be useful for other i.MX platforms
implement the imx_obtain_fixed_clock() function in common code.

Actually changing other i.MX platforms to use this should be done
later by someone with access to the appropriate hardware.
Signed-off-by: NMartin Fuzzey <mfuzzey@parkeon.com>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Use imx_clk_mux_flags to set the appropriate flags for the TVE
selector clock. This is needed so tve_clk rate changes can propagate
up to pll4_sw.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Remove the tve_di clock from the CCM clock tree. It will be provided
by the Television Encoder driver, as this clock is an output signal
of the TVE module.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This is needed so the Television Encoder driver can set the rate
on tve_clk and have it propagated up to pll4_sw.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

On i.MX53, there is only tve_ext_sel.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This adds the clock gates and the binding documentation
for PATA and SRTC.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

These two clocks connect to external pins and can be muxed to
various internal clocks.
They are typically used either for debugging or to provide
clocks to external chips (eg audio codecs).

Currently only the selectable clocks that already exist in the clock tree
have been added.
Signed-off-by: NMartin Fuzzey <mfuzzey@parkeon.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Use imx_clk_mux_flags and imx_clk_divider_flags to set the appropriate
flags for the LDB display interface divider and selector clocks.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds the missing GPU2D and GPU3D mux and gate clocks,
and the graphics arbiter gate clock.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add cpufreq-cpu0 platform device for imx5 DT init and register the clock
for imx5.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMartin Fuzzey <mfuzzey@parkeon.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

As we use platform_device_id for fsl-usb2-udc driver, it needs to
change clk connection-id, or the related devm_clk_get will be failed.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>