There's no need to do some kind of weird err and RCU dance
just use sta_info_insert() directly.

Link: https://lore.kernel.org/r/20210517230754.55abd10056c0.I6f5a3b7b23347b2cdaf64e6d5ce1d9e904059654@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

In some race conditions, with more clients and traffic configuration,
below crash is seen when making the interface down. sta->fast_rx wasn't
cleared when STA gets removed from 4-addr AP_VLAN interface. The crash is
due to try accessing 4-addr AP_VLAN interface's net_device (fast_rx->dev)
which has been deleted already.

Resolve this by clearing sta->fast_rx pointer when STA removes
from a 4-addr VLAN.

[  239.449529] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[  239.449531] pgd = 80204000
...
[  239.481496] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.60 #227
[  239.481591] Hardware name: Generic DT based system
[  239.487665] task: be05b700 ti: be08e000 task.ti: be08e000
[  239.492360] PC is at get_rps_cpu+0x2d4/0x31c
[  239.497823] LR is at 0xbe08fc54
...
[  239.778574] [<80739740>] (get_rps_cpu) from [<8073cb10>] (netif_receive_skb_internal+0x8c/0xac)
[  239.786722] [<8073cb10>] (netif_receive_skb_internal) from [<8073d578>] (napi_gro_receive+0x48/0xc4)
[  239.795267] [<8073d578>] (napi_gro_receive) from [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames+0xbcc/0x12d4 [mac80211])
[  239.804776] [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<c7b84d4c>] (ieee80211_rx_napi+0x7b8/0x8c8 [mac8
            0211])
[  239.815857] [<c7b84d4c>] (ieee80211_rx_napi [mac80211]) from [<c7f63d7c>] (ath11k_dp_process_rx+0x7bc/0x8c8 [ath11k])
[  239.827757] [<c7f63d7c>] (ath11k_dp_process_rx [ath11k]) from [<c7f5b6c4>] (ath11k_dp_service_srng+0x2c0/0x2e0 [ath11k])
[  239.838484] [<c7f5b6c4>] (ath11k_dp_service_srng [ath11k]) from [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll+0x20/0x84 [ath11k_ahb]
            )
[  239.849419] [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll [ath11k_ahb]) from [<8073ce1c>] (net_rx_action+0xe0/0x28c)
[  239.860945] [<8073ce1c>] (net_rx_action) from [<80324868>] (__do_softirq+0xe4/0x228)
[  239.871269] [<80324868>] (__do_softirq) from [<80324c48>] (irq_exit+0x98/0x108)
[  239.879080] [<80324c48>] (irq_exit) from [<8035c59c>] (__handle_domain_irq+0x90/0xb4)
[  239.886114] [<8035c59c>] (__handle_domain_irq) from [<8030137c>] (gic_handle_irq+0x50/0x94)
[  239.894100] [<8030137c>] (gic_handle_irq) from [<803024c0>] (__irq_svc+0x40/0x74)
Signed-off-by: NSeevalamuthu Mariappan <seevalam@codeaurora.org>
Link: https://lore.kernel.org/r/1616163532-3881-1-git-send-email-seevalam@codeaurora.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

s/assocaited/associated/
Signed-off-by: NBhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Coverity reported the strange "if (~...)" condition that's
always true. It suggested that ! was intended instead of ~,
but upon further analysis I'm convinced that what really was
intended was a comparison to 0xff/0xffff (in HT/VHT cases
respectively), since this indicates that all of the rates
are enabled.

Change the comparison accordingly.

I'm guessing this never really mattered because a reset to
not having a rate mask is basically equivalent to having a
mask that enables all rates.
Reported-by: NColin Ian King <colin.king@canonical.com>
Fixes: 2ffbe6d3 ("mac80211: fix and optimize MCS mask handling")
Fixes: b119ad6e ("mac80211: add rate mask logic for vht rates")
Reviewed-by: NColin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210212112213.36b38078f569.I8546a20c80bc1669058eb453e213630b846e107b@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

This change registers ieee80211_set_sar_specs to
mac80211_config_ops, so cfg80211 can call it.
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Reviewed-by: NAbhishek Kumar <kuabhs@chromium.org>
Link: https://lore.kernel.org/r/20201203103728.3034-3-cjhuang@codeaurora.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Use a struct assignment here, which is clearer than the
memcpy() and type-safe as well.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.2ab3aad7d5fc.Iaca4ee6db651b7de17e4351f4be7973ff8600186@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

We don't really use this struct, we're now using
struct cfg80211_he_bss_color instead.

Change the one place in mac80211 that's using the old
name to use struct assignment instead of memcpy() and
thus remove the wrong sizeof while at it.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.f6698d97ae4e.Iba2dffcb79c4ab80bde7407609806010b55edfdf@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

In the NL80211_CMD_CH_SWITCH_STARTED_NOTIFY event, include the
NL80211_ATTR_CH_SWITCH_BLOCK_TX flag attribute if block-tx was
requested by the AP.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201129172929.8953ef22cc64.Ifee9cab337a4369938545920ba5590559e91327a@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of
letting the code fall through to the next case.

Link: https://github.com/KSPP/linux/issues/115Signed-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/1a9c4e8248e76e1361edbe2471a68773d87f0b67.1605896060.git.gustavoars@kernel.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Now that all the mac80211-based drivers have removed WDS code
and in particular the ability to advertise such devices, also
remove all the code related to WDS here.

Link: https://lore.kernel.org/r/20201109105103.38960c413d46.I3603c90a44562d847c39d15d5ff33d8c00df5834@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd.
This information needs to be passed to the driver when the rate control
is offloaded to the firmware. The driver capability of allowing beacon
rate is already validated in cfg80211, so simply passing the rate
information to the driver is enough.
Signed-off-by: NRajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1601762658-15627-1-git-send-email-rmanohar@codeaurora.org
[adjust commit message slightly]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Even though a driver or mac80211 shouldn't produce a
legacy bitrate if sband->bitrates doesn't exist, don't
crash if that is the case either.

This fixes a kernel panic if station dump is run before
last_rate can be updated with a data frame when
sband->bitrates is missing (eg. in S1G bands).
Signed-off-by: NThomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201005164522.18069-1-thomas@adapt-ip.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

The changes required for associating in S1G are:

- apply S1G BSS channel info before assoc
- mark all S1G STAs as QoS STAs
- include and parse AID request element
- handle new Association Response format
- don't fail assoc if supported rates element is missing
Signed-off-by: NThomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-15-thomas@adapt-ip.com
[pass skb to ieee80211_add_aid_request_ie(), remove unused variable 'bss']
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch adds mac80211 support to configure unsolicited
broadcast probe response transmission for in-band discovery in 6GHz.

Changes include functions to store and retrieve probe response template,
and packet interval (0 - 20 TUs).
Setting interval to 0 disables the unsolicited broadcast probe response
transmission.
Signed-off-by: NAloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/010101747a946b35-ad25858a-1f1f-48df-909e-dc7bf26d9169-000000@us-west-2.amazonses.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch adds mac80211 support to configure FILS discovery
transmission.
Changes include functions to store and retrieve FILS discovery
template, minimum and maximum packet intervals.
Signed-off-by: NAloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/20200805011838.28166-3-alokad@codeaurora.org
[remove SUPPORTS_FILS_DISCOVERY, driver can just set wiphy info]
Link: https://lore.kernel.org/r/010101747a7b3cbb-6edaa89c-436d-4391-8765-61456d7f5f4e-000000@us-west-2.amazonses.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

This is needed for encapsulation offload of 4-address mode packets
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-14-nbd@nbd.nameSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.

Make this safer by inverting the polarity from 'disabled' to
'enabled'.

Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

The flags argument in transmit functions is no longer being used
and can be removed.
Signed-off-by: NMathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-5-Mathy.Vanhoef@kuleuven.beSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Adding bss-color configuration is only valid in HE mode.
Earlier we have enabled it by default, irrespective of
capabilities/mode. Fix that.
Reported-by: Nkernel test robot <lkp@intel.com>
Reported-by: NRajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: NP Praneesh <ppranees@codeaurora.org>
Link: https://lore.kernel.org/r/1594262781-21444-1-git-send-email-ppranees@codeaurora.org
[fix up commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Besides information about num of peerings and gate connectivity,
the mesh formation byte also contains a flag for authentication
server connectivity, that currently cannot be set in the mesh conf.
This patch adds this capability, which is necessary to implement
802.1X authentication in mesh mode.
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200611140238.427461-1-markus.theil@tu-ilmenau.deSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.

When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.

The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.

mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.

For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.

Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NLinus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200707204548.GA9320@embeddedorSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

At ieee80211_join_mesh() some ie data could have been allocated (see
copy_mesh_setup()) and need to be cleaned up when leaving the mesh.

This fixes the following kmemleak report:

unreferenced object 0xffff0000116bc600 (size 128):
  comm "wpa_supplicant", pid 608, jiffies 4294898983 (age 293.484s)
  hex dump (first 32 bytes):
    30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00  0...............
    00 0f ac 08 00 00 00 00 c4 65 40 00 00 00 00 00  .........e@.....
  backtrace:
    [<00000000bebe439d>] __kmalloc_track_caller+0x1c0/0x330
    [<00000000a349dbe1>] kmemdup+0x28/0x50
    [<0000000075d69baa>] ieee80211_join_mesh+0x6c/0x3b8 [mac80211]
    [<00000000683bb98b>] __cfg80211_join_mesh+0x1e8/0x4f0 [cfg80211]
    [<0000000072cb507f>] nl80211_join_mesh+0x520/0x6b8 [cfg80211]
    [<0000000077e9bcf9>] genl_family_rcv_msg+0x374/0x680
    [<00000000b1bd936d>] genl_rcv_msg+0x78/0x108
    [<0000000022c53788>] netlink_rcv_skb+0xb0/0x1c0
    [<0000000011af8ec9>] genl_rcv+0x34/0x48
    [<0000000069e41f53>] netlink_unicast+0x268/0x2e8
    [<00000000a7517316>] netlink_sendmsg+0x320/0x4c0
    [<0000000069cba205>] ____sys_sendmsg+0x354/0x3a0
    [<00000000e06bab0f>] ___sys_sendmsg+0xd8/0x120
    [<0000000037340728>] __sys_sendmsg+0xa4/0xf8
    [<000000004fed9776>] __arm64_sys_sendmsg+0x44/0x58
    [<000000001c1e5647>] el0_svc_handler+0xd0/0x1a0

Fixes: c80d545d (mac80211: Let userspace enable and configure vendor specific path selection.)
Signed-off-by: NRemi Pommarel <repk@triplefau.lt>
Link: https://lore.kernel.org/r/20200704135007.27292-1-repk@triplefau.ltSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Set short slot also for 6 GHz band, just like 5 GHz.
Signed-off-by: NTova Mussai <tova.mussai@intel.com>
Link: https://lore.kernel.org/r/20200528213443.75f38e6f5efd.I272fbae402b03123f04e9ae69204eeab960c70cd@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to handle 6 GHz AP side, take the HE 6 GHz band capability
data and pass it to the driver (which needs it for A-MPDU spacing
and A-MPDU length).

Link: https://lore.kernel.org/r/1589399105-25472-6-git-send-email-rmanohar@codeaurora.orgCo-developed-by: NRajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/20200528213443.784e4890d82f.I5f1230d5ab27e84e7bbe88e3645b24ea15a0c146@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Fix all variable names from 'tid' to 'tids' to avoid confusion.
Now this is not TID number, but TID mask.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-3-sergey.matyukevich.os@quantenna.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Use the Beacon frame specific legacy rate configuration, if specified
for AP or mesh, instead of the generic rate mask when selecting the TX
rate for Beacon frames.
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200425155713.25687-4-jouni@codeaurora.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

cfg80211_chan_def and ieee80211_channel recently gained a
frequency offset component. Handle this where it makes
sense (potentially required by S1G channels).

For IBSS, TDLS, CSA, and ROC we return -EOPNOTSUPP if a
channel with frequency offset is passed, since they may or
may not work. Once someone tests and verifies these
commands work on thos types of channels, we can remove
that error.

join_ocb and join_mesh look harmless because they use a
simple ieee80211_vif_use_channel(), which is using an
already verified channel, so we let those through.
Signed-off-by: NThomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-4-thomas@adapt-ip.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Convert a user space registration for processing multicast Action frames
(NL80211_CMD_REGISTER_FRAME with NL80211_ATTR_RECEIVE_MULTICAST) to a
new enum ieee80211_filter_flags bit FIF_MCAST_ACTION so that drivers can
update their RX filter parameters appropriately, if needed.
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200421144815.19175-1-jouni@codeaurora.org
[rename variables to rx_mcast_action_reg indicating action frames only]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.

Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

There are two bugs with this, first, it shouldn't be called
on an interface that's down, and secondly, it should then be
called when the interface comes up.

Note that the currently only user (iwlwifi) doesn't seem to
care about either of these scenarios.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200417111830.401d82c7a0bf.I5dc7d718816460c2d8d89c7af6c215f9e2b3078f@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

In AP mode, set htc_trig_based_pkt_ext and frame_time_rts_th
for driver use.
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-19-luca@coelho.fiSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch adds support for disabling pre-auth rx over the nl80211 control
port for mac80211.
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200312091055.54257-3-markus.theil@tu-ilmenau.de
[fix indentation slightly, squash feature enablement]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement drv_set_tid_config api to allow TID specific
configuration and drv_reset_tid_config api to reset peer
specific TID configuration. This per-TID onfiguration
will be applied for all the connected stations when MAC is NULL.
Signed-off-by: NTamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-7-git-send-email-tamizhr@codeaurora.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Extend mac80211 key configuration to support the new BIGTK with key
index values 6 and 7. Support for actually protecting Beacon frames
(adding the MME in AP mode and checking it in STA mode) is covered in
separate commits.
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-3-jouni@codeaurora.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

The SMPS feature is defined in the specification only to be
used by non-AP stations and not by APs, so remove the support
for changing the AP's SMPS mode dynamically.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-20-luca@coelho.fiSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

It turns out that this wasn't a good idea, I hit a test failure in
hwsim due to this. That particular failure was easily worked around,
but it raised questions: if an AP needs to, for example, send action
frames to each connected station, the current limit is nowhere near
enough (especially if those stations are sleeping and the frames are
queued for a while.)

Shuffle around some bits to make more room for ack_frame_id to allow
up to 8192 queued up frames, that's enough for queueing 4 frames to
each connected station, even at the maximum of 2007 stations on a
single AP.

We take the bits from band (which currently only 2 but I leave 3 in
case we add another band) and from the hw_queue, which can only need
4 since it has a limit of 16 queues.

Fixes: 6912daed ("mac80211: Shrink the size of ack_frame_id to make room for tx_time_est")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NToke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200115122549.b9a4ef9f4980.Ied52ed90150220b83a280009c590b65d125d087c@changeidSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

It is now possible to propagate BSS color settings into the subsystem. Lets
make mac80211 also handle them so that we can send them further down the
stack into the drivers. We drop the old bss_color field and change iwlwifi
to use the new he_bss_color struct.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191217141921.8114-2-john@phrozen.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

In case a radar event of CAC_FINISHED or RADAR_DETECTED
happens during another phy is during CAC we might need
to cancel that CAC.

If we got a radar in a channel that another phy is now
doing CAC on then the CAC should be canceled there.

If, for example, 2 phys doing CAC on the same channels,
or on comptable channels, once on of them will finish his
CAC the other might need to cancel his CAC, since it is no
longer relevant.

To fix that the commit adds an callback and implement it in
mac80211 to end CAC.
This commit also adds a call to said callback if after a radar
event we see the CAC is no longer relevant
Signed-off-by: NOrr Mazor <Orr.Mazor@tandemg.com>
Reviewed-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20191222145449.15792-1-Orr.Mazor@tandemg.com
[slightly reformat/reword commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>