Fix ll_temac and emaclite drivers. Only Microblaze and Xilinx PPC
use then and both use NO_IRQ as 0. It will be removed in near future.
Signed-off-by: NMichal Simek <monstr@monstr.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If recovery is triggered in presence of pending asynchronous
deliveries of storage blocks we do a forced cleanup after
the corresponding tasklets are completely stopped and trigger
appropriate notifications for the correspondingerror state.
Signed-off-by: NEinar Lueck <elelueck@de.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case there are no system resources to run a recovery we have to clear
recovery bitmasks so a further automatic or manual driven recovery can
fix up the device.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NETIUCV device driver allows to connect a Linux guest on z/VM to
another z/VM guest based on the z/VM communication facility IUCV.
Multiple output paths to different guests are possible, as well as
multiple input paths from different guests.
With this feature, you can configure multiple point-to-point NETIUCV
interfaces between your Linux on System z instance and another z/VM
guest.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A recovery does not make sense during shutdown and may even cause an
error like this:

qeth 0.0.f503: A recovery process has been started for the device
Badness at drivers/s390/cio/qdio_main.c:1156
Modules linked in: autofs4 sunrpc dm_multipath scsi_dh scsi_mod qeth_l3 ipv6 vmu
r qeth qdio ccwgroup ext3 jbd mbcache dasd_eckd_mod dasd_mod dm_mirror dm_region
_hash dm_log dm_mod [last unloaded: scsi_wait_scan]
CPU: 3 Not tainted 2.6.32-202.el6.s390x #1
Process qeth_recover (pid: 1498, task: 000000003efe2040, ksp: 000000003d5e3b80)
Krnl PSW : 0404200180000000 000003c000be6da8 (qdio_int_handler+0x88/0x43c [qdio]
)
           R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:2 PM:0 EA:3
Krnl GPRS: ffffffffffff3bac 0000000000000005 0000000000000000 fffffffffffffff4
           0000000000000000 000000000000000c 0000000000000000 000000003ca97000
           0000000000000380 fffffffffffffff4 000000003f22d800 000000003f22c478
           000003c000bdf000 000003c000bea270 000000003f447e10 000000003f447db0
Krnl Code: 000003c000be6d9a: c21f00000004       clfi    %r1,4
           000003c000be6da0: a7c40021           brc     12,3c000be6de2
           000003c000be6da4: a7f40001           brc     15,3c000be6da6
          >000003c000be6da8: e320a0080004       lg      %r2,8(%r10)
           000003c000be6dae: a7390003           lghi    %r3,3
           000003c000be6db2: a72b0178           aghi    %r2,376
           000003c000be6db6: a7490001           lghi    %r4,1
           000003c000be6dba: a7590000           lghi    %r5,0
Call Trace:
([<000000000080ee80>] __per_cpu_offset+0x0/0x200)
[<00000000003d90e8>] ccw_device_call_handler+0x70/0xcc
[<00000000003d83a2>] ccw_device_irq+0x82/0x180
[<00000000003cc6a8>] do_IRQ+0x16c/0x1ec
[<0000000000118abe>] io_return+0x0/0x8
[<000003c000d04c74>] qeth_determine_capabilities+0x208/0x5cc [qeth]
([<000003c000d04c4a>] qeth_determine_capabilities+0x1de/0x5cc [qeth])
[<000003c000d0a6e0>] qeth_core_hardsetup_card+0x160/0x1258 [qeth]
[<000003c000f49f56>] __qeth_l3_set_online+0x132/0xb14 [qeth_l3]
[<000003c000f4ac70>] qeth_l3_recover+0x168/0x224 [qeth_l3]
[<000000000016e210>] kthread+0xa4/0xac
[<0000000000109c6e>] kernel_thread_starter+0x6/0xc
[<0000000000109c68>] kernel_thread_starter+0x0/0xc

The patch forbids start of a recovery once qeth shutdown is running.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qeth layer3 recovery invokes its set_multicast_list function, which
invokes function __vlan_find_dev_deep requiring rcu_read_lock or
rtnl lock. This causes kernel messages:

kernel: [ INFO: suspicious rcu_dereference_check() usage. ]
kernel: ---------------------------------------------------
kernel: net/8021q/vlan_core.c:70 invoked rcu_dereference_check() without protection!

kernel: stack backtrace:
kernel: CPU: 0 Not tainted 3.1.0 #9
kernel: Process qeth_recover (pid: 2078, task: 000000007e584680, ksp: 000000007e3e3930)
kernel: 000000007e3e3d08 000000007e3e3c88 0000000000000002 0000000000000000
kernel:       000000007e3e3d28 000000007e3e3ca0 000000007e3e3ca0 00000000005e77ce
kernel:       0000000000000000 0000000000000001 ffffffffffffffff 0000000000000001
kernel:       000000000000000d 000000000000000c 000000007e3e3cf0 0000000000000000
kernel:       0000000000000000 0000000000100a18 000000007e3e3c88 000000007e3e3cc8
kernel: Call Trace:
kernel: ([<0000000000100926>] show_trace+0xee/0x144)
kernel: [<00000000005d395c>] __vlan_find_dev_deep+0xb0/0x108
kernel: [<00000000004acd3a>] qeth_l3_set_multicast_list+0x976/0xe38
kernel: [<00000000004ae0f4>] __qeth_l3_set_online+0x75c/0x1498
kernel: [<00000000004aefec>] qeth_l3_recover+0xc4/0x1d0
kernel: [<0000000000185372>] kthread+0xa6/0xb0
kernel: [<00000000005ed4c6>] kernel_thread_starter+0x6/0xc
kernel: [<00000000005ed4c0>] kernel_thread_starter+0x0/0xc

The patch makes sure the rtnl lock is held once qeth recovery invokes
its set_multicast_list function.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was reported that the macvtap device selects a
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When UDP RSS is enabled, we use same QPN for TCP and UDP ranges
The bug is that the default_qpn was used base UDP qpn before it
was set.
Fixes bug introduced in commit: 1202d460Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.

(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).

Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DaveM said:
   Please, this kind of stuff rots forever and not using bool properly
   drives me crazy.

Joe Perches <joe@perches.com> gave me the spatch script:

	@@
	bool b;
	@@
	-b = 0
	+b = false
	@@
	bool b;
	@@
	-b = 1
	+b = true

I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NFrederic Lambert <frdrc66@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace open-coded list traversal with list_for_each_entry().

CC: Grant Grundler <grundler@parisc-linux.org>
CC: netdev@vger.kernel.org
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace open-coded list traversal with list_for_each_entry().

CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the ethtool callbacks necessary to change the rss
indirection table from userspace.  Should the number of interrupts
change (e.g.  across a close / open call, or through a reset) and
any one of the indirection table values fall out-of-range, the driver
will reset the indirection table to a default layout.

[Integrated many suggestions made by Ben Hutchings.]

Changes since v3

* Removed TG3_FLAG_SUPPORT_MSIX checks at the start of
  tg3_get_rxfh_indir() and tg3_set_rxfh_indir().
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2-mips-06-6.2.3 and bnx2-mips-09-6.2.1.b

New firmware fixes iSCSI problems with some LeftHand targets that don't
set TTT=0xffffffff for Data-In according to spec.  Firmware generates
exception warnings for this condition and becomes very slow.  This is
fixed by suppressing these warnings when using default error mask.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lancer does not have HW registers to indicate the EQ causing the INTx
interrupt. As a result EQE entries of one EQ may be consumed when interrupt
is caused by another EQ. Fix this by arming CQs at the end of NAPI poll
routine to regenerate the EQEs.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVinson Lee <vlee@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The communication channel is HW interface from PF point of view
So the command return status should be stored as HW error code
and only then translated to errno values.
Reporetd-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function is always called from irq context, changing the call
to spin_lock().
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Solves an issue where we tried to free the same page twice after
the port has been opened and closed.
Signed-off-by: NAlexander Guller <alexg@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New FW can give clues to driver regarding default port type
and whether or not we should default to link sensing on the port.

2 bits are added to QUERY_PORT command:
1. suggested_type: This bit gives a hint whether the default port type should be
   IB or Ethernet.
   The driver will use this hint in case the user didn't specify explicitly the link layer
   type he wants to set.
2. default_sense: If this bit is set, we would sense the port type on start-up
   and default the port to link sensing
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For ConnectX3 devices, we allow link sensing only if FW explicitly
reported it supports the feature.
For older versions (ConnectX1 and 2), if the card supports both link layer types
(Ethenet and Infiniband), link sensing is supported.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"result" isn't used.  We ignore errors here because there is not much we
can do about them.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a compile error that occurs when the driver
is compile into the kernel and not as a module.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

All drivers that support modification of the RX flow hash indirection
table initialise it in the same way: RX rings are assigned to table
entries in rotation.  Make that default policy explicit by having them
call a ethtool_rxfh_indir_default() function.

In the ethtool core, add support for a zero size value for
ETHTOOL_SRXFHINDIR, which resets the table to this default.
Partly-suggested-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new ethtool operation (get_rxfh_indir_size) to get the
indirectional table size.  Use this to validate the user buffer size
before calling get_rxfh_indir or set_rxfh_indir.  Use get_rxnfc to get
the number of RX rings, and validate the contents of the new
indirection table before calling set_rxfh_indir.  Remove this
validation from drivers.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a few minor issues with wmediumd_pid:
a) make static
b) use u32 to match the snd_pid type
c) use ACCESS_ONCE since we don't lock it
d) don't explicitly initialize to 0
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

its not used anywhere in the current code
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

before concluding that the recieved beacon is for us, let us make sure
that the BSSID is non-zero. when I configured ad-hoc mode as creator and
left it for some time without joining I found we recieved few frames whose
BSSID is zero, which we concluded wrongly as 'my_beacons'
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Negate has higher precendence than compare and since neither zero nor
one are equal to four or eight the original condition is always false.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This initial DFS module provides basic functionality to deal
with radar pulses reported by the Atheros DFS HW pulse detector.

The reported data is evaluated and basic plausibility checks
are performed to filter false pulses. Passing radar pulses are
forwarded to pattern detectors which are not yet implemented.

(Some modifications to actually use ATH9K_DFS_DEBUGFS based on comments
from Julian Calaby <julian.calaby@gmail.com>. -- JWL)
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to enable DFS upstream we want to be sure
DFS has been tested for each chipset. Push for public
documentation of the requirements we want in place and
allow for enabling each chipset through a single upstream
commit.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This can later be used by other drivers that implement
DFS support.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In ai_attach(), space is allocated for an si_info struct. Immediately
after the allocation, routine ai_doattach() is called and that allocated
space is set to zero. As no other routine calls ai_doattach(), kzalloc()
can be utilized.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A debug level was added to the ath module for printing
MCI messages but no documentation was provided. Clarify that
MCI is the Message Coexistence Interface, a private protocol
used exclusively for WLAN-BT coexistence starting from
AR9462.

Cc: wtsao@qca.qualcomm.com
Cc: rmanohar@qca.qualcomm.com
Cc: mohammed@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The receiver will discard them anyway.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>