Update Copyright to 2012
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The transport doesn't need to access it any more.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with the mapping of RA / TID to HW queues in AGG.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since packets sent to an RA / TID in AGG are sent from a
separate HW Tx queue, we may get into a race:
the regular queue isn't empty while we already begin to
send packets from the AGG queue. This would result in sending
packets out of order.

In order to cope with this, mac80211 waits until the driver
reports that the legacy queue is drained before it can send
packets to the AGG queue. During that time, mac80211 buffers
packets for the driver. These packets will be sent in order
after the driver reports it is ready.

The way this was implemented in the driver is as follows:
We held a counter that monitors the number of packets for
an RA / TID in the HW queues. When this counter reached 0,
we knew that the HW queues were drained and we reported to
mac80211 that were ready to proceed.

This patch changes the implementation described above. We
now remember what is the wifi sequence number of the first
packet that will be sent in the AGG queue (lets' call it
ssn). When we reclaim the packet before ssn, we know that
the queue is drained, and we are ready to proceed.

This will allow us to move this logic in the upper layer and
eventually remove the tid_data from the shared area.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Move the configuration pointer from the upper level iwl_priv to the
lower level iwl_shared structure, with associated code fixes.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The eeprom image is a device level component, move from iwl_priv
to iwl_shared, with associated code changes.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Move the ucode_type variable from the iwl_priv to the iwl_shared
structure with associated code changes.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the ucode_type variable from the iwl_priv to the iwl_shared
structure with associated code changes.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The nvm_device_type is eeprom related and does not need to be part
of the iwl_priv structure.  Move it and eliminate access to the iwl_priv
structure.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Relocate the ucode files and update relevant code.
More code refactoring.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not needed since driver split.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For command queue testing, add "echo test" to debugfs
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since priv->temperature is signed, we cannot use debugfs_create_u32
to refer to it.
Use a regular debugfs file instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The debug_level and temperature files should be in
debugfs, the txpower file is completely unneeded
since TX power can be set with iw/iwconfig.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The traffic log debugfs handlers were mistakenly moved to the
transport layer because they print the pointers of the Tx / Rx
queues. The pointers of the queues can be fetched by another debugfs
handler.
So bring the traffic log back to the upper layer and remove the part
that reads the Tx / Rx queues' pointers.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rate scaling and the transport need to access the data in
iwl_tid_data, hence the move.

Note that the only component in the upper layer that needs this data
is the rate scaling. Refactoring the rate scaling may help to move
iwl_tid_data from the shared area to the transport area.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Which means that iwl-io.c doesn't need to include iwl-dev.h any more.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These are transport layer related. Move also the corresponding debugfs handlers.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Logic move after all priv->status moved to struct iwl_shared
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is accessed by the transport layer only, hence the move.
The debugfs handlers that accessed it moved to the transport layer too.
The rx_handlers part of it stayed in the upper layer and a special debugfs
has been added for it

Also add missing includes to iwl-commands.h.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is transport dependent, move to the PCIe transport layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a handler in iwl_trans_ops to allow it to add entries under debugfs dir
given by the upper level.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will allow all the modules to look at it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The latter may return incomplete information.
For example, if one switched IWL_DL_TX on through sysfs, IWL_DL_TX bit would
have been set in priv->debug_level, but since iwl_alloc_traffic_mem looked at
iwl_debug_level only, it wouldn't have allocated the tx_traffic buffer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement WoWLAN support in iwlagn. The device
supports a number of wakeup triggers and can do
GTK rekeying when asleep (if HW crypto is used).
Unfortunately, we need to disconnect from the AP
after resume since we can't yet get all the info
out of the wowlan uCode to stay connected safely.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

After driver split, extra _agn in priv structure is no needed, remove it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

After driver split, no need to make indirect call to txfifo flush function
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The ucode subtypes keep changing, and there's no
particular reason to be checking them (other than
a paranoid sanity check). Since the numbers are
also in conflict between different ucode images
now, simply don't check them any more and rely on
the images being built correctly.

Also, to indicate that, rename the constants and
the enum, moving it to a different file.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

After driver split, no need for debugfs callback, remove those
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

On new hardware, ucode images always come in
pairs: code and data. Therefore, combine the
variables into an appropriate struct and use
that when both code and data are needed.

Also, combine allocation and copying so that
we have less code in total.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The current firmware loading mechanism in
iwlwifi is very hard to follow, and thus
hard to maintain. To make it easier, make
the firmware loading synchronous.

For now, as a side effect, this removes a
number of retry possibilities we had. It
isn't typical for this to fail, but if it
does happen we restart from scratch which
this also makes easier to do should it be
necessary.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

All _agn devices support continuous uCode trace, remove checking
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

There's no need to keep both normal and BT statistics
versions around all the time in memory when we only
use a subset of both. So keep only the subsets that
we need in memory, depending on the debug config).

Also, in doing so, we can remove all the calls to
iwl_bt_statistics() in the driver as we'll just
access the copied statistics now.

Finally, also remove this call from the one place
where it might still be needed and automatically
detect what kind of statistics the device is sending
based on their size. This way, we don't need to keep
track of which devices do what any more, which is
good since this is subject to change based on the
ucode version (as some ucode even for non-BT devices
will in fact use BT statistics).

Warn upon encountering a statistics command from the
ucode that isn't known, so we will find such issues
earlier in the future.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Tested-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

_agn driver should perform both sensitivity and chain noise calib.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Remove the config flag for tx power calib
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Remove broken_power_save checking
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

After driver split, no need to use function pointer for those event and
register dump function.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>