ath10k_pci_read32/write32() does work more specific to
PCI by ensuring pci wake/sleep for every read and write.
There is a plan to use most of stuff available in pci.c
(irq stuff, copy engine, etc) for AHB case. Such kind
of pci wake/sleep for every read/write is not required
in AHB case (qca4019). All those reusable areas in pci.c
and ce.c calls ath10k_pci_read32/write32() for low level
read and write.

In fact, ath10k_pci_read32/write32() should do what it does
today for PCI case. But for AHB, it has to do differently.
To make ath10k_pci_read32/write32() more generic, new function
pointers are added in ar_pci for the function which does
operation more close to the bus. Later, corresponding bus
specific read and write function will be mapped to that.

ath10k_pci_read32/write32() are changed to call directly
those function pointers without worrying which bus underlying
to it. Also, the function to get number of bank is changed
in the same way.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some of static functions present in pci.c file are reusable
in ahb (qca4019) case. Remove static word for those reusable
functions and have those function prototype declaration in
pci.h file. So that, pci.h header file can be included in
ahb module and reused. There is no functionality changes done
in this patch.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For devices that does not support PCI power save, force wake up
API is used. So move powersave check inside force wakeup to reduce
one level indentation.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

commit 1aaf8efb ("ath10k: disable PCI PS for QCA988X
and QCA99X0") partially reverts pci soc powersave support added by
commit 77258d40 ("ath10k: enable pci soc powersaving"). While
reverting the change, pci wake up function is called after accessing
pci registers instead of prior to access. The assumption is that chip
is woken up before accessing its registers.Though this change does not
fix any known issues, this might help to avoid unknown or low power
platform specific issues.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

commit a70587b3 ("ath10k: configure copy engine 5 for HTT messages")
moved send completion polling under HTT Rx (CE 5) service routine. For
QCA6174 based devices copy engine 1 (CE 1) is used for HTT Rx instead
of CE 5. So send completion never be called. This is causing "failed to
transmit packet, dropping: -105" errors. Fix this by processing send
completion from CE 1 service routine instead of CE 5.

Fixes: a70587b3 ("ath10k: configure copy engine 5 for HTT messages")
Tested-by: NRyan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Commit a70587b3 ("ath10k: configure copy engine 5 for HTT messages")
introduced to use the unused CE5 for target to host message. For the device
like QCA6174, CE5 already assigned for other feature. So for QCA6174, override
the CE5 configuration and use the CE1 instead.

This patch is based on Rajkumar's earlier patch.

Fixes: a70587b3 ("ath10k: configure copy engine 5 for HTT messages")
Signed-off-by: NRyan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add new BMI target version and chip id revision. Register it
on supported chips list.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

A follow up patch introducing a QCA9377 hw1.0 support will need
this device identification helper for an explicit distinction of
HWs, as apparently both QCA6174 hw3.0 and QCA9377 share the same BMI
target version (0x0502000x). For the QCA9377 hw1.1 previously
added we were just lucky we did not overlap with the same chip_id_rev.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When introducing the original QCA9377 support, the chip target
version was wrongly picked. The chip advertising itself with
bmi target value equal to 0x05020001 is in fact a 1.1 revision.
I realized this once I got a real 1.1 hw to play with.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch adds pktlog support for 10.4 fw versions.
Signed-off-by: NVivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add the hardware name, revision and update the pci_id table.

Currently there're two HW ref. designs available I'm aware of,
with 1.0.2 and 1.1 chip revisions. I've access and been using
the first one so far and this patch cover only it.

QCA9377 inherits most of the stuff (e.g. fw interfaces)
from QCA61x4 design, so the integration was pretty straightforward.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For the messages from host to target, shadow copy of CE descriptors
are maintained in source ring. Before writing actual CE descriptor,
first shadow copy is filled and then it is copied to CE address space.
To optimize in download path and to reduce d-cache pressure, removing
shadow copy of CE descriptors. This will also reduce driver memory
consumption by 33KB during on device probing.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. ath10k doesn't rely on the meta/transfer_id
when handling send completion (htc ep id is stored in sk_buff control
buffer). So the unused output arguments {bufferp, nbytesp and transfer_idp}
are removed from CE send completion. This change is needed before removing
the shadow copy of copy engine (CE) descriptors in follow up patch.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

CE diag window access is serialized (it has to be by design) so
there's no way to get a different send completion. so there's no
need for post completion validation.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch disables PCI PS for QCA988X and QCA99X0, Since PCI PS is
validated for QCA6174, let it be enabled only for QCA6174. It would be
better to execute PCI PS related functions only for the supported devices.

PCI time out issue is observed with QCA99X0 on x86 platform, We will
disable PCI PS for QCA988X and QCA99X0 until PCI PS is properly implemented.

Taking and releasing ps_lock is causing higher CPU consumption. Michal Kazior
suggested ps_lock overhead to be reworked so that ath10k_pci_wake/sleep
functions are called less often, i.e. move the powersave logic up (only during
irq handling, tx path, submitting fw commands) but that's a bigger change and
can be implemented later.
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since polling for tx completion is handled whenever target to host
messages are received, removing the unnecessary polling mechanism for
send completion at HTC level.
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since polling for received messages not supported, remove unused
dl_is_polled.
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently target to host (T2H) HTT messages are received at copy engine 1.
These messages are processed by HTC layer in both host and target.
To avoid HTC level processing overhead in both host and target,
the unused copy engine 5 is being used for receiving HTT T2H messages.
This will speedup the receive data processing as well as htt tx completion.
Hence host and target copy engine configuration tables are updated
to enable CE5 pipe. The in-direction HTT mapping is now pointing to CE5
for all HTT T2H.

Moreover HTT send completion messages are polled from HTC handler
as CE 4 is not interrupt-driven. For faster tx completion, CE4 polling
needs to be done whenever CE pipe which transports HTT Rx (target->host)
is processed. This avoids overhead of polling HTT messages from HTC
layer. Servicing CE 4 faster is helping to solve "failed to transmit
packet, dropping: -105".
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Register receive callbacks for every copy engines (CE) separately
instead of having common receive handler. Some of the copy engines
receives different type of messages (i.e HTT/HTC/pktlog) from target.
Hence to service them accordingly, register per copy engine receive
callbacks.
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Register send completion callbacks for every copy engines (CE) separately
instead of having common completion handler. Since some of the copy
engines delivers different type of messages, per-CE callbacks help to
service them differently.
Reviewed-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA6174 needs different board files based on board type. To make it easier to
distribute multiple board files and automatically choose correct board file
create a simple TLV file format following the same principles as with FW IEs.
The file is named board-2.bin and contain multiple board files. Each board file
then can have multiple names.

ath10k searches for file board-N.bin (where N is the interface version number
for the board file, just like we for firmware files) in /lib/firmware/*, for
example for qca99x0 it will try to find it here:

/lib/firmware/ath10k/QCA99X0/hw2.0/board-2.bin

If ath10k doesn't find board-2.bin then it will fallback to the old board.bin file.

This patch adds a simple name scheme using pci device id which for now will be
used by qca6174:

bus=%s,vendor=%04x,device=%04x,subsystem-vendor=%04x,subsystem-device=%04x

This removes the old method of having subsystem ids in ar->spec_board_id and
using that in the board file name.
Signed-off-by: NManikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: simplified the file format, rewrote commit log, other smaller changes]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

After processing received packets from copy engine, host will allocate
new buffer and queue them back to copy engine ring for further
packet reception. On post rx processing path, skb allocation and
dma mapping are unnecessarily handled within ce_lock. This is affecting
peak throughput and also causing more CPU consumption. Optimize this
by acquiring ce_lock only when accessing copy engine ring and moving
skb allocation out of ce_lock.

In AP148 platform with QCA99x0 in conducted environment, UDP uplink peak
throughput is improved from ~1320 Mbps to ~1450 Mbps and TCP uplink peak
throughput is increased from ~1240 Mbps (70% host CPU load) to ~1300 Mbps
(71% CPU load). Similarly ~40Mbps improvement is observed in downlink
path.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is noticed that pci wakeup time is exceeding current timeout (10ms)
randomly which is tested on QCA988x. So, the wake up time is increased
to 30 ms and added debug prints to log total timeout.
Signed-off-by: NMaharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

checkpatch found:

drivers/net/wireless/ath/ath10k/core.c:574: Blank lines aren't necessary before a close brace '}'
drivers/net/wireless/ath/ath10k/mac.c:4067: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4083: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4084: spaces required around that '>>=' (ctx:WxV)
drivers/net/wireless/ath/ath10k/pci.c:1507: Missing a blank line after declarations
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

checkpatch found:

drivers/net/wireless/ath/ath10k/core.c:513: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/core.c:1266: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1267: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1268: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1269: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/mac.c:4659: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6271: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/pci.c:2260: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/wmi.c:3510: Alignment should match open parenthesis
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case of qca99x0 and MSI-X supported/enabled we
failed during interrupts registering with message:

ath10k_pci 0000:04:00.0: failed to request MSI-X ce irq 50: -22

Issue/fix was reproduced/tested using Dell Latitude E6430 laptop.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This adds additional 0x0041 PCI Device ID
definition to ath10k for QCA6164 which is a 1
spatial stream sibling of the QCA6174 (which is 2
spatial stream chip).

The QCA6164 needs a dedicated board.bin file which
is different than the one used for QCA6174. If the
board.bin is wrong the device will crash early
while trying to boot firmware. The register dump
will look like this:

 ath10k_pci 0000:02:00.0: firmware register dump:
 ath10k_pci 0000:02:00.0: [00]: 0x05010000 0x000015B3 0x000A012D 0x00955B31
 ...

Note the value 0x000A012D.

Special credit goes to Alan Liu
<alanliu@qca.qualcomm.com> for providing support
help which enabled me to come up with this patch.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The function returns 1 when DMA mapping fails. The
driver would return bogus values and could
possibly confuse itself if DMA failed.

Fixes: 767d34fc ("ath10k: remove DMA mapping wrappers")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add vendor/device id of QCA99X0 V2.0 to pci id table and
QCA99X0_HW_2_0_CHIP_ID_REV to ath10k_pci_supp_chips[] for
QCA99X0 to get detected by the driver.

kvalo: now QCA99X0 family of chipsets is supported by ath10k.
Tested client, AP and monitor mode with QCA9990.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is observed that during cold reset pcie access right
after a write operation to SOC_GLOBAL_RESET_ADDRESS causes
Data Bus Error and system hard lockup. The reason
for bus error is that pcie needs some time to get
back to stable state for any transaction during cold reset. Add
delay of 20 msecs after write of SOC_GLOBAL_RESET_ADDRESS
to fix this issue. This patch is tested on QCA988X. This is
also tested on QCA99X0 which is WIP.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In commit 418ca599 ("ath10k: Make target cpu address to
CE address conversion chip specific") mask 0x7fff is added
by mistake instead of 0x7ff. Fix this regression.

Fixes: 418ca599 ("ath10k: Make target cpu address to CE address conversion chip specific")
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA99X0 supports only cold reset. Also, made
ath10k_pci_irq_msi_fw_mask() and ath10k_pci_irq_msi_fw_unmask()
non-99X0 specific till we get proper register configuration
to mask/unmask irq/MSI.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make the helper converting target virtual address space to CE address
space a target type specific to support QCA99X0. Also make this as
function instead of macro.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA99X0 supports upto 12 Copy engines. Host and target
CE configuration table is updated to support new copy engine
pipes. This also fixes the assumption of diagnostic CE by making
CE_7 as the one instead of CE_COUNT - 1.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to prepare the driver for QCA99X0 chip support.
This commit adds hw_params, hw register table and hw_values
table for QCA99X0 chip. Please note this is only a partial patch adding
support for QCA99X0, so the device id is not yet added to pci device
table.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was possible to force an out of bounds MMIO
read/write via debugfs. E.g. on QCA988X this could
be triggered with:

 echo 0x2080e0 | tee /sys/kernel/debug/ieee80211/*/ath10k/reg_addr
 cat /sys/kernel/debug/ieee80211/*/ath10k/reg_value

 BUG: unable to handle kernel paging request at ffffc90001e080e0
 IP: [<ffffffff8135c860>] ioread32+0x40/0x50
 ...
 Call Trace:
  [<ffffffffa00d0c7f>] ? ath10k_pci_read32+0x4f/0x70 [ath10k_pci]
  [<ffffffffa0080f50>] ath10k_reg_value_read+0x90/0xf0 [ath10k_core]
  [<ffffffff8115c2c1>] ? handle_mm_fault+0xa91/0x1050
  [<ffffffff81189758>] __vfs_read+0x28/0xe0
  [<ffffffff812e4694>] ? security_file_permission+0x84/0xa0
  [<ffffffff81189ce3>] ? rw_verify_area+0x53/0x100
  [<ffffffff81189e1a>] vfs_read+0x8a/0x140
  [<ffffffff8118acb9>] SyS_read+0x49/0xb0
  [<ffffffff8104e39c>] ? trace_do_page_fault+0x3c/0xc0
  [<ffffffff8196596e>] system_call_fastpath+0x12/0x71
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

mete_data is extracted from ce descriptor and stored in variable 'id'.
later, id is not used anywhere in the same function.

Fixes: d84a512d ("ath10k: remove transfer_id from ath10k_hif_cb::tx_completion")
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If probing failed pci sleep timer could remain
running and trigger after ath10k structures were
freed causing invalid pointer dereference:

 BUG: unable to handle kernel paging request at ffffc90001c80004
 IP: [<ffffffff81354728>] iowrite32+0x38/0x40
 ...
 Call Trace:
  <IRQ>
  [<ffffffffa00da048>] ? __ath10k_pci_sleep+0x48/0x60 [ath10k_pci]
  [<ffffffffa00da44e>] ath10k_pci_ps_timer+0x5e/0x80 [ath10k_pci]
  [<ffffffff810b210e>] call_timer_fn+0x3e/0x120
  [<ffffffffa00da3f0>] ? ath10k_pci_wake+0x150/0x150 [ath10k_pci]
  [<ffffffff810b3d11>] run_timer_softirq+0x201/0x2e0
  [<ffffffff8105d73f>] __do_softirq+0xaf/0x290
  [<ffffffff8105da95>] irq_exit+0x95/0xa0
  [<ffffffff81950406>] smp_apic_timer_interrupt+0x46/0x60
  [<ffffffff8194e77e>] apic_timer_interrupt+0x6e/0x80

Fixes: 77258d40 ("ath10k: enable pci soc powersaving")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This could lead userspace initram images getting
built without necessary firmware files included
leading to probing failures of ath10k on boot with
QCA61X4.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

By using SOC_WAKE register it is possible to bring
down power consumption of QCA61X4 from 36mA to
16mA when associated and idle.

Currently the sleep threshold/grace period is at a
very conservative value of 60ms.

Contrary to QCA61X4 the QCA988X firmware doesn't
have Rx/beacon filtering available for client mode
and SWBA events are used for beaconing in AP/IBSS
so the SoC needs to be woken up at least every
~100ms in most cases. This means that QCA988X
is at a disadvantage and the power consumption
won't drop as much as for QCA61X4.

Due to putting irq-safe spinlocks on every MMIO
read/write it is expected this can cause a little
performance regression on some systems. I haven't
done any thorough measurements but some of my
tests don't show any extreme degradation.

The patch removes some explicit pci_wake calls
that were added in 320e14b8db51aa ("ath10k: fix
some pci wake/sleep issues"). This is safe because
all MMIO accesses are now wrapped and the device
is woken up automatically if necessary.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>