This patch adds support for usb2.0 host ch3 device nodes for R-Car
H3 ES2.0.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds support for usb3_phy ch3 device node for R-Car H3 ES2.0.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds the "companion" property in the EHCI ch0, ch1 and
ch2 nodes to wait for the usb companion controller startup at resume.
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
[remove ch3 node and revise the commit log]
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Basic support for the Renesas Draak board based on R-Car D3:
  - Memory,
  - Main crystal,
  - Serial console,
  - Watchdog.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Basic support for the R-Car D3 SoC:
  - PSCI,
  - CPU,
  - Cache controller,
  - Main clocks and controller,
  - Interrupt controller,
  - Timer,
  - Watchdog,
  - PMU,
  - Reset controller,
  - Product register,
  - System controller,
  - UART for console.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The DU dot clocks 0 and 3 are provided by the programmable VC6 clock
generator. Connect them to the clock source node.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The VC6 is an I2C-controlled programmable clock generator, used on the
board to provide a display dot clock. Add it to DT.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

MSIOF0 and MSIOF1 are tied to two DMA controllers through two pairs of
DMA specifiers.  However, the second pair of corresponding DMA names was
missing.

Fixes: 80fab06e ("arm64: dts: r8a7796: Add all MSIOF nodes")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the device nodes for all MSIOF SPI controllers, incl. clocks, power
domain, dma, and reset properties.

Due to a hardware erratum on R-Car H3 ES1.x, using MSIOF for SPI is only
supported on ES2.0 and later.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a compatible string and VSP links to the DU node. The H3 ES1.x and
H3 ES2.0 are compatible save for the links to the VSPs that are
described explicitly in DT, so there's no need for a new ES2-specific
compatible string.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable the HDMI encoder for ULCB board and hook it up to the HDMI connector.

The HDMI encoder and connector are available on both the H3 and M3-W ULCB boards.
Add them to the ulcb.dtsi file.
Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The ULCB board has one HDMI output connector.

This connector is available on both the H3 and M3-W ULCB boards.
Add this to the ulcb.dtsi file.
Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The DU0/DU1/DU2 external dot clocks are provided by the programmable
Versaclock5 clock generator.
Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The DU0/DU1/DU2/DU3 external dot clocks are provided by the programmable
Versaclock5 clock generator.
Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The DU0/DU1/DU2/DU3 external dot clocks are generated by an I2C-controlled
programmable clock generator.

Clock generator is available on both the H3 and M3-W ULCB boards.
Add this to the ulcb.dtsi file.
Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable the HDMI encoder for the M3-W Salvator-X board and hook it up to
the HDMI connector.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The DU1 external dot clock is provided by the fixed frequency clock
generator X21, while the DU0 and DU2 clocks are provided by the
programmable Versaclock5 clock generator.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the HDMI encoder to the R8A7796 DT in disabled state.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the DU device to r8a7796.dtsi in a disabled state.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The r8a7796 has 5 VSP instances.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The FCPs handle the interface between various IP cores and memory. Add
the instances related to the FDPs and VSP2s.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This enables I2C4 for ULCB board
Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This enables I2C for DVFS device for ULCB board
Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Adds the DRIF controller nodes for r8a7795.
Signed-off-by: NRamesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Adds the DRIF controller nodes for r8a7796.
Signed-off-by: NRamesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The definition of CPG_AUDIO_CLK_I is SoC-specific, not board-specific.
Hence move it from the board-specific .dts files to the SoC-specific
.dtsi files.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the IMR-LX4 devices in the R8A7796 device tree.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the IMR-LX4 devices in the R8A7795 device tree.

Based on the original (and large) patch by Konstantin Kozhevnikov
<Konstantin.Kozhevnikov@cogentembedded.com>.
Signed-off-by: NKonstantin Kozhevnikov <Konstantin.Kozhevnikov@cogentembedded.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Contrary to popular belief, PPIs connected to a GICv3 to not have
an affinity field similar to that of GICv2. That is consistent
with the fact that GICv3 is designed to accomodate thousands of
CPUs, and fitting them as a bitmap in a byte is... difficult.

Fixes: adbc3695 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

This reverts commits 2c0cba48 ("arm: sun8i: sunxi-h3-h5: Add dt node
for the syscon control module") to 2428fd0f ("arm64: defconfig: Enable
dwmac-sun8i driver on defconfig") and 3432a86e ("arm: sun8i:
orangepipc: use internal phy-mode") to 5a79b4f2 ("arm: sun8i:
orangepi-2: use internal phy-mode") that should be merged
through the arm-soc tree, and end up in merge conflicts and build failures.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As I found by chance while merging another patch, the usage of
a dma-mask in this DT node is wrong for multiple reasons:

- dma-masks are a Linux specific concept, not a general
  hardware feature
- In DT, we use the "dma-ranges" property to describe how DMA
  addresses related between devices.
- The 40-bit mask appears to be completely unnecessary here, as
  the SoC cannot address that much memory anyway, so simply
  asking for a 64-bit mask (as supported by the device) should
  succeed anyway.

The patch to remove the parsing of the property is getting merged
through the crypto tree.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This resolves a build error in the next/dt branch:

In file included from arch/arm64/boot/dts/mediatek/mt6797-evb.dts:16:0:
arch/arm64/boot/dts/mediatek/mt6797.dtsi:15:10: fatal error: dt-bindings/power/mt6797-power.h: No such file or directory

003f5d0c ("arm64: dts: mediatek: add clk and scp nodes for MT6797")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add support for the CC  board from Shenzhen Libre Technology
More information about the board are available here:

https://libre.computer/blog/

Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This commit modifies the Marvell EBU Armada 7K and 8K Device Tree files
to describe the ICU and GICP units, and use ICU interrupts for all
devices in the CP110 blocks.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Compiling the DT file with W=1, DTC warns like follows:

Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property

Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: NKrzysztof Kozlowski <krzk@kernel.org>
Reported-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable gpio support for CP and AP on the Marvell Armada 7K/8K SoCs.

The Armada 8K has two CP110 blocks, each having two GPIO controllers.
However, in each CP110 block, one of the GPIO controller cannot be
used: in the master CP110, only the second GPIO controller can be used,
while on the slave CP110, only the first GPIO controller can be used.

On the other side, the Armada 7K has only one CP110, but both its GPIO
controllers can be used.

For this reason, the GPIO controllers are marked as "disabled" in the
armada-cp110-master.dtsi and armada-cp110-slave.dtsi files, and only
enabled in the per-SoC dtsi files.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Enable pinctrl support for CP and AP on the Armada 7K/8K SoCs.

The CP master being different between Armada 7k and Armada 8k. This
commit introduces the intermediates files armada-70x0.dtsi and
armada-80x0.dtsi.

These new files will provide different compatible strings depending of
the SoC family. They will also be the location for the pinmux
configuration at the SoC level.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The new binding for the system controller on cp110 moved the clock
controller into a subnode. This preliminary step will allow to add gpio
and pinctrl subnodes.
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The *-clock-output-names of the cp110-system-controller0 node are not
used anymore, so remove them.
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

New bindings are used for the system controller on the ap806, which
means all clock properties must be converted. Use the new bindings in
the xor nodes.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>