On the regulatory notifier split up the parsing of the
hints coming from drivers or user. We'll treat these
separately.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This moves the dynamic regulatory domain selection code into
a helper.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers can now use this to parse the regulatory request and
be more verbose when needed.
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the RF chip supports more than 14 channels that
indirectly means that it supports the 5GHz band.
Use this fact to enable 5GHz band support instead
of setting SUPPORT_BAND_5GHZ separately for each
RF chip.

Also move the setup code of the 2GHz band to the
same place.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is much more readable than multiple if-else-if
statements.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The {rx,tx}_chain_num fields of rt2x00dev->default_ant
contains the number of RX and TX chains already when the
rt2800_probe_hw_mode() function runs. Use those values
instead of parsing the EEPROM configuration values again.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the DFS pattern detector code to the ath module so
the other Atheros drivers can make us of it. This makes
no functional changes.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use CFG80211_CERTIFICATION_ONUS flag in the DFS
detector code. This is required as a preparation
for moving DFS detector code from ath9k to ath
module.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move ath_dfs_pool_stats to dfs_pattern_detector
code to be not specyfic only for ath9k.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kill of using ath9k_hw_common() function
in dfs detector code.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously, each bus type was responsible for freeing the firmware
structure, but some did that badly.  Move responsibility for freeing
firmware into firmware.c so that it's done once and correctly, instead
of happening in multiple places in bus-specific code.

This fixes a use-after-free bug found by Dr. H. Nikolaus Schaller where
the SDIO code forgot to NULL priv->helper_fw after freeing it.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add spectral scan feature on HT40 channels for ath9k. This patch extends
previous capability added by Simon Wunderlich
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Reviewed-by: NSimon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Tested-by: NSimon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add nf parameter to ath9k_hw_getchan_noise() in order to compute NF for EXT
chains with the same scale of noise floor calculated on CTL chains.
ath9k_hw_getchan_noise() will be used in ath_process_fft() for spectral scan on
HT40 channels
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Samuel Ortiz <sameo@linux.intel.com> says:

"This is the first NFC pull request for the 3.13 kernel.
It's a fairly big one, with the following highlights:

- NFC digital layer implementation: Most NFC chipsets implement the NFC
  digital layer in firmware, but others have more basic functionalities
  and expect the host to implement the digital layer. This layer sits
  below the NFC core.

- Sony's port100 support: This is "soft" NFC USB dongle that expects the
  digital layer to be implemented on the host. This is the first user of
  our NFC digital stack implementation.

- Secure element API: We now provide a netlink API for enabling,
  disabling and discovering NFC attached (embedded or UICC ones) secure
  elements. With some userspace help, this allows us to support NFC
  payments.
  Only the pn544 driver currently supports that API.

- NCI SPI fixes and improvements: In order to support NCI devices over
  SPI, we fixed and improved our NCI/SPI implementation. The currently
  most deployed NFC NCI chipset, Broadcom's bcm2079x, supports that mode
  and we're planning to use our NCI/SPI framework to implement a
  driver for it.

- pn533 fragmentation support in target mode: This was the only missing
  feature from our pn533 impementation. We now support fragmentation in
  both Tx and Rx modes, in target mode."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Integers need to be multiplied before division.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The fw_rx_stats entry in debugfs was getting truncated because the
internal buffer used to hold the string was too short.  The
calculation of the needed buffer size was rather bogus.

Simplify the calculation by multiplying the number of entries in the
entire structure by the size of each data line and adding the size of
the header lines.

Additionally, add the mac_id value, which was missing.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The activity grading indication from the firmware should
not be used in this case, but the bt_status in the firwmare
notification.
Fix that.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The firmware always expects the Coex Mode to be set.
Moreover, the firmware expects bit 0 is the valid bits to
be set all the times.
I misunderstood the API and didn't set these bits when
commands are sent to update the paramters of the Coex. As
a result, the firmware understood that the BT Coex was
disabled (Coex mode = 0) and ignored all the updates (valid
bit 0 clear).

Fix that.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Section size limitation to 6000 is incorrect.
NVM file need to support bigger sections in order
to support PAPD tables.
Signed-off-by: NIdan Kahlon <idanx.kahlon@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NMaor Perez <maorx.perez@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ath10k_wmi_cmd_send() will now sleep if there are no credits available.
To make it easier to catch callers in atomic context add might_sleep()
to the function.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_bss_assoc() was calling ath10k_peer_assoc(), which can sleep, under
atomic rcu_read_lock() and causing scheduing while atomic errors. Workaround
that by delaying the call to ath10k_wmi_peer_assoc().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

mac80211 interface iteration functions that were
used originally iterated over interfaces that
weren't re-added to the driver during recovery.

Since internal vif list is now used it's safe to
remove the safe-guard as internal vif list is
based on add/remove_interface function which
guarantees that vdev is created in FW before it is
iterated over.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Recent HTC/WMI changes introduced the bug. ath10k
was using _atomic iteration function with
sleepable functions.

mac80211 provides another iteration function but
it cannot be safely called in hw_config() callback
due to local->iflist_mtx being possibly acquired
already.

The patch uses internal vif list for iteration
purposes and removes/refactors no longer necessary
_iter functions.
Reported-By: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

mac80211 interface interations functions have
peculiar locking issues. This patch introduces
internal (to ath10k) vif list that will be used
for vif iteration purposes.

kvalo: remove extra INIT_LIST_HEAD()
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If something failed along add_interface() setup it
was possible to leak a vdev id, vdev and peer.

This could end up with leaked FW state or FW crash
(assuming add_interface() failure wasn't a result of
a crash).

kvalo: rebased, whitespace fixes
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Recent WMI/HTC changes made it possible for WMI
commands to sleep (if there's not enough HTC TX
credits to submit a command). TX path is in an
atomic context so calling WMI commands in it is
wrong.

This simply moves WEP key index update to a worker
and fixes the 'scheduling while atomic' bug.

This still leaves multiple WEP key handling laggy,
i.e. some frames may be TXed with an old/different
key (although recipient should still be able to RX
them).

kvalo: changed the title
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Return -EOPNOTSUPP if given parameter is not supported by firmware.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Rename WMI_CMD_UNDEFINED to WMI_CMD_UNSUPPORTED. This is more
accurate here. Also return -EOPNOTSUPP instead of -EINVAL in
wmi_cmd_send().
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.X firmware does not support WMI_VDEV_PARAM_TX_ENCAP_TYPE.
It's a known limitation and we should not warn about this.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Read the current IAC LAP values when initializing the controller. The
values are not used, but it is good to have them in the trace files
for debugging purposes.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When initializing a controller make sure to read out the number of
supported IAC and store its result. This value is needed to determine
if limited discoverable for BR/EDR can be configured or not.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The scan window parameter for connection establishment and passive
scanning needs to be smaller or equal than the scan interval.

Instead of waiting for a controller to reject these values later on,
just reject them right away.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

If a socket was bound to an address type other than BR/EDR (such as LE)
we should reject trying to connect it to a BR/EDR address. The same
applies for binding to BR/EDR and trying to connect to non-BR/EDR.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We need to verify that the bdaddr type passed to connect() and bind() is
within the set of valid values. If it is not we need to cleanly fail
with EINVAL.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch converts Set Discoverable to use an asynchronous request
along with its own completion callback. This is necessary for splitting
raw HCI socket use cases from mgmt, as well as for enabling the hooking
up of Advertising parameters together with the HCI_DISCOVERABLE flag
(coming in later patches).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Now that the connectable setting is also applicable for the LE side it's
possible that the HCI_CONNECTABLE flag is already set when changing the
BR/EDR setting from false to true while the controller is powered. In
this situation we need to update the BR/EDR scan mode to reflect the
setting. Additionally, since HCI_CONNECTABLE also applies to LE we must
not clear the HCI_CONNECTABLE flag when disabling bredr.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The set_bredr_scan() function will soon be needed by the set_bredr()
function, so move it to a new location to avoid having to add a forward
declaration.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>