Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid using value stored in the login response buffer when
cleaning TX and RX buffer pools since these could be inconsistent
depending on the device state. Instead use the field in the driver's
private data that tracks the number of active pools.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.

Fixes: e05107e6 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver.  This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.

Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096.  Move the kzalloc() call
into the bnxt_get_pkgver() function.

Fixes: 3ebf6f0a ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When longer interface names are used, the action names exposed in
/proc/interrupts and /proc/irq/* maybe truncated. For example, when
using the predictable name algorithm in systemd on a HiSilicon D05,
I see:

  ubuntu@d05-3:~$  grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
  enahisic2i0-tx0
  enahisic2i0-tx1
  [...]
  enahisic2i0-tx8
  enahisic2i0-tx9
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1

Increase the max ring name length to allow for an interface name
of IFNAMSIZE. After this change, I now see:

  $ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
  enahisic2i0-tx0
  enahisic2i0-tx1
  enahisic2i0-tx2
  [...]
  enahisic2i0-tx8
  enahisic2i0-tx9
  enahisic2i0-tx10
  enahisic2i0-tx11
  enahisic2i0-tx12
  enahisic2i0-tx13
  enahisic2i0-tx14
  enahisic2i0-tx15
Signed-off-by: Ndann frazier <dann.frazier@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ACS Feature is currently enabled for GMAC >= 4 but the llc_snap status
is never checked in descriptor rx_status callback. This will cause
stmmac to always strip packets even that ACS feature is already
stripping them.

Lets be safe and disable the ACS feature for GMAC >= 4 and always strip
the packets for this GMAC version.

Fixes: 477286b5 ("stmmac: add GMAC4 core support")
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PPv2 TX/RX descriptors uses 40bits DMA addresses, but 41 bits masks were
used (GENMASK_ULL(40, 0)).

This commit fixes that by using the correct mask.

Fixes: e7c5359f ("net: mvpp2: introduce PPv2.2 HW descriptors and adapt accessors")
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the last rmnet device attached to a real device is removed, the
real device is unregistered from rmnet. As a result, the real device
lookup fails resulting in a warning when the fill_info handler is
called as part of the rmnet device unregistration.

Fix this by returning the rmnet flags as 0 when no real device is
present.

WARNING: CPU: 0 PID: 1779 at net/core/rtnetlink.c:3254
rtmsg_ifinfo_build_skb+0xca/0x10d
Modules linked in:
CPU: 0 PID: 1779 Comm: ip Not tainted 4.16.0-11872-g7ce23672 #1
Stack:
 7fe655f0 60371ea3 00000000 00000000
 60282bc6 6006b116 7fe65600 60371ee8
 7fe65660 6003a68c 00000000 900000000
Call Trace:
 [<6006b116>] ? printk+0x0/0x94
 [<6001f375>] show_stack+0xfe/0x158
 [<60371ea3>] ? dump_stack_print_info+0xe8/0xf1
 [<60282bc6>] ? rtmsg_ifinfo_build_skb+0xca/0x10d
 [<6006b116>] ? printk+0x0/0x94
 [<60371ee8>] dump_stack+0x2a/0x2c
 [<6003a68c>] __warn+0x10e/0x13e
 [<6003a82c>] warn_slowpath_null+0x48/0x4f
 [<60282bc6>] rtmsg_ifinfo_build_skb+0xca/0x10d
 [<60282c4d>] rtmsg_ifinfo_event.part.37+0x1e/0x43
 [<60282c2f>] ? rtmsg_ifinfo_event.part.37+0x0/0x43
 [<60282d03>] rtmsg_ifinfo+0x24/0x28
 [<60264e86>] dev_close_many+0xba/0x119
 [<60282cdf>] ? rtmsg_ifinfo+0x0/0x28
 [<6027c225>] ? rtnl_is_locked+0x0/0x1c
 [<6026ca67>] rollback_registered_many+0x1ae/0x4ae
 [<600314be>] ? unblock_signals+0x0/0xae
 [<6026cdc0>] ? unregister_netdevice_queue+0x19/0xec
 [<6026ceec>] unregister_netdevice_many+0x21/0xa1
 [<6027c765>] rtnl_delete_link+0x3e/0x4e
 [<60280ecb>] rtnl_dellink+0x262/0x29c
 [<6027c241>] ? rtnl_get_link+0x0/0x3e
 [<6027f867>] rtnetlink_rcv_msg+0x235/0x274

Fixes: be81a85f ("net: qualcomm: rmnet: Implement fill_info")
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some firmware variants - specifically 'capture packed stream' - RSS
filters are not valid. We must check if RSS is actually active rather
than merely enabled.

Fixes: 42356d9a ("sfc: support RSS spreading of ethtool ntuple filters")
Signed-off-by: NBert Kenward <bkenward@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to a firmware bug, the hypervisor can send an interrupt to a
transmit or receive queue just prior to a partition migration, not
allowing the device enough time to handle it and send an EOI. When
the partition migrates, the interrupt is lost but an "EOI-pending"
flag for the interrupt line is still set in firmware. No further
interrupts will be sent until that flag is cleared, effectively
freezing that queue. To workaround this, the driver will disable the
hardware interrupt and send an H_EOI signal prior to re-enabling it.
This will flush the pending EOI and allow the driver to continue
operation.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marvell's PPv2 controller has a Packet Header parser, which uses a
fixed-size TCAM array of filter entries.

The mvpp2 driver reserves some ranges among the 256 TCAM entries to
perform MAC and VID filtering. The rest of the TCAM ids are freely usable
for other features, such as IPv4 proto matching.

This commit fixes the MVPP2_PE_LAST_FREE_TID define that sets the end of
the "free range", which included the MAC range. This could therefore allow
some other features to use entries dedicated to MAC filtering,
lowering the number of unicast/multicast addresses that could be allowed
before switching to promiscuous mode.

Fixes: 10fea26c ("net: mvpp2: Add support for unicast filtering")
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A misconfigured system (e.g. with all interrupts affinitised to all CPUs)
 may produce a storm of ARFS steering events.  With the existing sfc ARFS
 implementation, that could create a backlog of workitems that grinds the
 system to a halt.  To prevent this, limit the number of workitems that
 may be in flight for a given SFC device to 8 (EFX_RPS_MAX_IN_FLIGHT), and
 return EBUSY from our ndo_rx_flow_steer method if the limit is reached.
Given this limit, also store the workitems in an array of slots within the
 struct efx_nic, rather than dynamically allocating for each request.
The limit should not negatively impact performance, because it is only
 likely to be hit in cases where ARFS will be ineffective anyway.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we inserted an ARFS filter for ndo_rx_flow_steer(), we didn't know
 what the filter ID would be, so we just returned 0.  Thus, we must also
 pass 0 as the filter ID when calling rps_may_expire_flow() for it, and
 rely on the flow_id to identify what we're talking about.

Fixes: 3af0f342 ("sfc: replace asynchronous filter operations")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Necessary to allow redirecting a flow when the application moves.

Fixes: 3af0f342 ("sfc: replace asynchronous filter operations")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a second skb list for handling control messages and limit the
number of allowed messages. Some control messages are considered more
crucial than others, resulting in the need for a second skb list. By
splitting the list into a separate high and low priority list we can
ensure that messages on the high list get added to the head of the list
that gets processed, this however has no functional impact. Previously
there was no limit on the number of messages allowed on the queue, this
could result in the queue growing boundlessly and eventually the host
running out of memory.

Fixes: b985f870 ("nfp: process control messages in workqueue in flower app")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we processed the route ack control messages in the workqueue,
this unnecessarily loads the workqueue. We can deal with these messages
sooner as we know we are going to drop them.

Fixes: 8e6a9046 ("nfp: flower vxlan neighbour offload")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When waiting for an NFP mutex is interrupted print a message
to make root causing later error messages easier.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently allow signals to interrupt the wait for management FW
commands.  Exiting the wait should not cause trouble, the FW will
just finish executing the command in the background and new commands
will wait for the old one to finish.

However, this may not be what users expect (Ctrl-C not actually stopping
the command).  Moreover some systems routinely request link information
with signals pending (Ubuntu 14.04 runs a landscape-sysinfo python tool
from MOTD) worrying users with errors like these:

nfp 0000:04:00.0: nfp_nsp: Error -512 waiting for code 0x0007 to start
nfp 0000:04:00.0: nfp: reading port table failed -512

Make the wait for management FW responses non-interruptible.

Fixes: 1a64821c ("nfp: add support for service processor access")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When attempting to change the driver parameters, such as the MTU
value or number of queues, do not call netdev_notify_peers().
Doing so will deadlock on the rtnl_lock.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a bug in handling the possible return codes from sending the
login CRQ. The current code treats any non-success return value,
minus failure to send the crq and a timeout waiting for a login response,
as a need to re-send the login CRQ. This can put the drive in an
infinite loop of trying to login when getting return values other
that a partial success such as a return code of aborted. For these
scenarios the login will not ever succeed at this point and the
driver would need to be reset again.

To resolve this loop trying to login is updated to only retry the
login if the driver gets a return code of a partial success. Other
return codes are treated as an error and the driver returns an error
from ibmvnic_login().

To avoid infinite looping in the partial success return cases, the
number of retries is capped at the maximum number of supported
queues. This value was chosen because the driver does a renegotiation
of capabilities which sets the number of queues possible and allows
the driver to attempt a login for possible value for the number
of queues supported.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "name" field of struct vnic_login_client_data is a char array of
undefined length. This should be written as "char name[]" so the compiler
can make better decisions about the field (for example, not assuming
it's a single character). This was noticed while trying to tighten the
CONFIG_FORTIFY_SOURCE checking.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When open fails during ethtool -L ring change, for example, the driver
may crash at bnxt_free_irq() because bp->bnapi is NULL.

If we fail to allocate all the new rings, bnxt_open_nic() will free
all the memory including bp->bnapi.  Subsequent call to bnxt_close_nic()
will try to dereference bp->bnapi in bnxt_free_irq().

Fix it by checking for !bp->bnapi in bnxt_free_irq().

Fixes: e5811b8c ("bnxt_en: Add IRQ remapping logic.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With recent changes to reserve both L2 and RDMA rings, we need to include
the RDMA rings in bnxt_check_rings().  Otherwise we will under-estimate
the rings we need during ethtool -L and may lead to failure.

Fixes: fbcfc8e4 ("bnxt_en: Reserve completion rings and MSIX for bnxt_re RDMA driver.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While a VF is configured with a bigger mtu (> 1500), any packets that
are punted to the VF-rep (slow-path) get dropped by OVS kernel-datapath
with the following message: "dropped over-mtu packet". Fix this by
returning the max-mtu value for a VF-rep derived from its corresponding VF.
VF-rep's mtu can be changed using 'ip' command as shown in this example:

	$ ip link set bnxt0_pf0vf0 mtu 9000
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently uses src port field (along with other fields) in the
decap tunnel key, while looking up and adding tunnel nodes. This leads to
redundant cfa_decap_filter_alloc() requests to the FW and flow-miss in the
flow engine. Fix this by ignoring the src port field in decap tunnel nodes.

Fixes: f484f678 ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this patch the following commands would succeed as far as the
user was concerned:

$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol all \
	flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:01/44 action drop

The current flow offload infrastructure used does not support wildcard
matching for ethernet headers, so do not allow the second or third
commands to succeed.  If a user wants to drop traffic on that interface
the protocol and MAC addresses need to be specified explicitly:

$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol arp \
	flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw action drop
...
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:01 action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:02 action drop
...

There are also checks for VLAN parameters in this patch as other callers
may wildcard those parameters even if tc does not.  Using different
flow infrastructure could allow this to work in the future for L2 flows,
but for now it does not.

Fixes: 2ae7408f ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix ethtool .get_rxfh() crash by checking for valid indirection table
address before copying the data.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case netdev is closed at the moment of pci shutdown, aq_nic_stop
gets called second time. napi_disable in that case hangs indefinitely.
In other case, if device was never opened at all, we get oops because
of null pointer access.

We should invoke aq_nic_stop conditionally, only if device is running
at the moment of shutdown.
Reported-by: NDavid Arcari <darcari@redhat.com>
Fixes: 90869ddf ("net: aquantia: Implement pci shutdown callback")
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On ASUS XG-C100C with 1.5.44 firmware a special mode called "dirty wake"
is active. With this mode when motherboard gets powered (but no poweron
happens yet), NIC automatically enables powersave link and watches
for WOL packet.
This normally allows to powerup the PC after AC power failures.

Not all motherboards or bios settings gives power to PCI slots,
so this mode is not enabled on all the hardware.

4.16 linux driver introduced full hardware reset sequence
This is required since before that we had no NIC hardware
reset implemented and there were side effects of "not clean start".

But this full reset is incompatible with "dirty wake" WOL feature
it keeps the PHY link in a special mode forever. As a consequence,
driver sees no link and no traffic.

To fix this we forcibly change FW state to idle state before doing
the full reset. This makes FW to restore link state.

Fixes: c8c82eb3 net: aquantia: Introduce global AQC hardware reset sequence
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is too expensive to pass u64 values via linked list, instead
allocate array for them by overall number of mac addresses from netdev.

This eventually removes multiple kmalloc() calls, aviod memory
fragmentation and allow to put single null check on kmalloc
return value in order to prevent a potential null pointer dereference.

Addresses-Coverity-ID: 1467429 ("Dereference null return value")
Fixes: 37c3347e ("net: thunderx: add ndo_set_rx_mode callback implementation for VF")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NVadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This resolves race during initialization where the resources with
ops are registered before driver and the structures used by occ_get
op is initialized. So keep occ_get callbacks registered only when
all structs are initialized.

The example flows, as it is in mlxsw:
1) driver load/asic probe:
   mlxsw_core
      -> mlxsw_sp_resources_register
        -> mlxsw_sp_kvdl_resources_register
          -> devlink_resource_register IDX
   mlxsw_spectrum
      -> mlxsw_sp_kvdl_init
        -> mlxsw_sp_kvdl_parts_init
          -> mlxsw_sp_kvdl_part_init
            -> devlink_resource_size_get IDX (to get the current setup
                                              size from devlink)
        -> devlink_resource_occ_get_register IDX (register current
                                                  occupancy getter)
2) reload triggered by devlink command:
  -> mlxsw_devlink_core_bus_device_reload
    -> mlxsw_sp_fini
      -> mlxsw_sp_kvdl_fini
	-> devlink_resource_occ_get_unregister IDX
    (struct mlxsw_sp *mlxsw_sp is freed at this point, call to occ get
     which is using mlxsw_sp would cause use-after free)
    -> mlxsw_sp_init
      -> mlxsw_sp_kvdl_init
        -> mlxsw_sp_kvdl_parts_init
          -> mlxsw_sp_kvdl_part_init
            -> devlink_resource_size_get IDX (to get the current setup
                                              size from devlink)
        -> devlink_resource_occ_get_register IDX (register current
                                                  occupancy getter)

Fixes: d9f9b9a4 ("devlink: Add support for resource abstraction")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This introduces a simpler and generic method for for finding (and mapping)
the TBIPA register.

Instead of relying of complicated logic for finding the TBIPA register
address based on the MDIO or MII register block base
address, which even in some cases relies on undocumented shadow registers,
a second "reg" entry for the mdio bus devicetree node specifies the TBIPA
register.

Backwards compatibility is kept, as the existing logic is applied when
only a single "reg" mapping is specified.
Signed-off-by: NEsben Haabendal <eha@deif.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When resetting the ibmvnic driver after a partition migration occurs
there is no requirement to do a reset of the main CRQ. The current
driver code does the required re-enable of the main CRQ, then does
a reset of the main CRQ later.

What we should be doing for a driver reset after a migration is to
re-enable the main CRQ, release all the sub-CRQs, and then allocate
new sub-CRQs after capability negotiation.

This patch updates the handling of mobility resets to do the proper
work and not reset the main CRQ. To do this the initialization/reset
of the main CRQ had to be moved out of the ibmvnic_init routine
and in to the ibmvnic_probe and do_reset routines.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a failover case for a non-redundant pseries VNIC
configuration that was not being handled properly. The current
implementation assumes that the driver will always have a redandant
device to communicate with following a failover notification. There
are cases, however, when a non-redundant configuration can receive
a failover request. If that happens, the driver should wait until
it receives a signal that the device is ready for operation.

The driver is agnostic of its backing hardware configuration,
so this fix necessarily affects all device failover management.
The driver needs to wait until it receives a signal that the device
is ready for resetting. A flag is introduced to track this intermediary
state where the driver is waiting for an active device.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some cases, if the driver is waiting for a reset following
a device parameter change, failure to schedule a reset can result
in a hang since a completion signal is never sent.

If the device configuration is being altered by a tool such
as ethtool or ifconfig, it could cause the console to hang
if the reset request does not get scheduled. Add some additional
error handling code to exit the wait_for_completion if there is
one in progress.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The counter that tracks used TX descriptors pending completion
needs to be zeroed as part of a device reset. This change fixes
a bug causing transmit queues to be stopped unnecessarily and in
some cases a transmit queue stall and timeout reset. If the counter
is not reset, the remaining descriptors will not be "removed",
effectively reducing queue capacity. If the queue is over half full,
it will cause the queue to stall if stopped.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix some mistakes caught by the DMA debugger. The first change
fixes a unnecessary unmap that should have been removed in an
earlier update. The next hunk fixes another bad unmap by zeroing
the bit checked to determine that an unmap is needed. The final
change fixes some buffers that are unmapped with the wrong
direction specified.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Joe Perches noted that we have a few source files that for some
inexplicable reason (read: I'm too lazy to even go look at the history)
are marked executable:

  drivers/gpu/drm/amd/amdgpu/vce_v4_0.c
  drivers/net/ethernet/cadence/macb_ptp.c

A simple git command line to show executable C/asm/header files is this:

    git ls-files -s '*.[chsS]' | grep '^100755'

and then you can fix them up with scripting by just feeding that output
into:

    | cut -f2 | xargs chmod -x

and commit it.

Which is exactly what this commit does.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

1) Return correct size from ice_get_regs_len.
2) Fix incorrect use of ARRAY_SIZE in ice_get_regs.

Fixes: fcea6f3d (ice: Add stats and ethtool support)
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix to return error code ICE_ERR_NO_MEMORY from the alloc error
handling case instead of 0, as done elsewhere in this function.

Fixes: dc49c772 ("ice: Get MAC/PHY/link info and scheduler topology")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>