This patch add snd_soc_dai_ops :: set_fmt to FSI driver and
select master/slave clock mode by snd_soc_dai_set_fmt on
fsi-xxx.c instead of platform infomation code.
This patch remove fsi_is_master function which is no longer needed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch support LEFT_J / I2S only for now
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch makes it easy to see when the syncing process begins and
ends.  You can also enable the snd_soc_reg_write tracepoint to see
which registers are being synced.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Added support for CS4271 codec to ASoC.
Signed-off-by: NAlexander Sverdlin <subaparts@yandex.ru>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The DC servo codes are actually signed numbers so need to be treated as
such.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org

The codec_name entry for da8xx evm in sound/soc/davinci/davinci-evm.c
is not matching with the i2c ids in the board file. Without this fix the
soundcard does not get detected on da850/omap-l138/am18x evm.
Signed-off-by: NRajashekhara, Sudhakar <sudhakar.raj@ti.com>
Tested-by: NDan Sharon <dansharon@nanometrics.ca>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37)

Also, update platform_data GPIO handling to have an explicit "don't
touch this pin" option.

Add #defines for the GPIO pin functions.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Incorporate the use of the cache_bypass functionality in the
syncing functions.  The snd_soc_flat_cache_sync() need not be
hooked as there is no performance benefit from using the
cache_bypass option.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is primarily needed to avoid writing back to the cache
whenever we are syncing the cache with the hardware.  This gives a
performance benefit especially for large register maps.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

fix wrong value in wm8994_set_tristate func. when updating reg bits,
it should use "value", not "reg".
Signed-off-by: NQiao Zhou <zhouqiao@marvell.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

In the wm8995_set_tristate() function when updating the register
bits use the value and not the register index as the value argument.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Many modern devices have features such as DC servos which take time to start.
Currently these are handled by per-widget events but this makes it difficult
to paralleise operations on multiple widgets, meaning delays can end up
being needlessly serialised. By providing a callback to drivers when all
widgets of a given type have been handled during a DAPM sequence the core
allows drivers to start operations separately and wait for them to complete
much more simply.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

With larger devices there may be many widgets of the same type in series
in an audio path. Allow drivers to specify an additional level of ordering
within each widget type by adding a subsequence number to widgets and then
splitting operations on widgets so that widgets of the same type but
different sequence numbers are processed separately.  A typical example
would be a supply widget which requires that another widget be enabled
to provide power or clocking.

SND_SOC_DAPM_PGA_S() and SND_SOC_DAPM_SUPPLY_S() macros are provided
allowing this to be used with PGAs and supplies as these are the most
commonly affected widgets.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Rather than passing the sequence to use for DAPM widgets around by reference
explicitly say if we're powering up or down until the point where we need
the sequence itself. This should make no practical difference in itself but
supports future refactoring.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The interface between sst platform driver and intel sst dsp driver
have been changed in Greg's staging tree - next branch

This patch adds the interface changes compatible with the new interface
in Greg's staging tree
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

snd_soc_dapm_new_widgets will call dapm_power_widgets at
the end, so there is no need to call snd_soc_dapm_sync
after snd_soc_dapm_new_widgets.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Reviewed-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

WM8750 address is 0x1b, not 0x1a. Without this fix ALSA detects no sound
cards on Zipit
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix jack detection on Zipit Z2, otherwise it
disables headphones output when jack is connected
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

While I2S/TDM/AC97 DAI is built-in, others are compiled as modules,
SND_BF5XX_SOC_SPORT will be module, then DAI can't get some symbols.
Except that, SND_BF5XX_AC97 depends on SND_BF5XX_SOC_AC97 too.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We don't want to use internal frame syncs otherwise we sometimes
get out of sync, so don't enable them when setting up the SPORT.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We need to tweak how we query the active capture/playback state after
the recent overhauls of common code.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

One spot was missed in this driver when converting from
snd_soc_dai.private_data to snd_soc_dai_get_drvdata.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Changelog:
1. I2S module of EP93xx should be feed by 32bit DMA transfers. This is
hardware limitation and that's the way original Cirrus's driver worked.
This will fix distorted sound playback and make capture actually work in
present ep93xx drivers.

I've found, that author of code, on which modern ep93xx-i2s.c and
ep93xx-pcm.c are based, had faced this problem also in 2007:
http://blog.gmane.org/gmane.linux.ports.arm.cirrus/month=20070101/page=3

Now SoC code uses his developments, but not overcomes the hardware
issues. Some details from EP93xx users guide:

Both I2S transmitter and receiver have similar 16x32bit FIFO, where they
store 8 samples for both left and right channels. The FIFO is always
32bit wide and should be properly aligned if you use samples of other
width. Transmitter and receiver have configuration registers for
selection of I2S word length (16, 24, 32). They are I2STXWrdLen and
I2SRXWrdLen.

Yes, EP93xx DMA can do byte, word and quad-word transfers. The width for
transfers to and from peripherals is selected by particular module
configuration. Lucky AC97 module has such configuration: AC97RXCRx
registers, bit CM (Compact mode enable) switches between 16 and 32 bit
samples. AC97TXCRx registers have the same bits for transmitters.
ep93xx-ac97.c enables this compact mode and so has all the rights to use
S16_LE format.
No one has found such a configuration in I2S module until now in any
Cirrus manuals. I2S module always feeds it's 32bit wide FIFO with 32bit
samples consecutively for left and right channels. You cannot use 32-bit
DMA transfers to transfer two 16-bit samples.

So we can use two formats for AC97, but should remove all but S32_LE for
I2S. Always using 32 bit chunks is not a problem for I2S, the codec I
use uses less bits too (24), it's permitted by I2S standard.

In proposed patch formats list shortened to just S32_LE, this makes all
the DMA transactions right, while ALSA will do all sample format
translation for us.

2. Incorrect setting of LRCLK (2 times slower) in original ep93xx-i2s.c
masks the first problem.

DMA takes two 16 bit samples instead of one, overall sound speed seems
to be normal, but you get actually 4000 sampling rate instead of
requested 8000 and therefore some noise... This is also the reason why
the capture function not worked at all in this driver...

If we take a look into I2S specification, we will figure that LRCLK MUST
be equal to sample rate, if we are talking about stereo (in mono too,
but it's not our case at all).

In proposed patch SCLK and LRCLK rates are corrected, assuming we always
send 32 bits * 2 channels to codec.
Signed-off-by: NAlexander Sverdlin <subaparts@yandex.ru>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Directly accessing the register cache means that we can't use anything
except a flat register cache so use snd_soc_update_bits().
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8991 is a highly integrated ultra-low power hi-fi CODEC designed for
handsets rich in multimedia features such as GPS, mobile TV, digital audio
playback and gaming.

This driver was originally written by Graeme Gregory and has been maintained
out of tree by Mark Brown and Dimitris Papastamos.
Signed-off-by: NGraeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The machine driver can't register the card directly and need to do this thru
soc-audio device creation

This patch allows the register and unregister card to be directly called by
machine drivers
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

With this change, I can capture from a microphone plugged into the
mic jack on Harmony (after unmuting Left Input PGA, and maybe turning
up the gain there too).
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

That config variable doesn't exist in the mainline kernel, and hence
the dependency shouldn't either.

In linux-tegra-2.6.36, the dependency did exist to avoid a conflict with
the old non-ALSA Tegra I2S driver. However, this isn't and won't be
upstreamed.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

These changes are needed to keep up with the changes in the
MFD core and V4L2 parts of the wl1273 FM radio driver.

Use function pointers instead of exported functions for I2C IO.
Also move all preprocessor constants from the wl1273.h to
include/linux/mfd/wl1273-core.h.
Signed-off-by: NMatti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Currently the soc_probe initializes the card hence it does the card list
initialzation. But if machines directly register the card they would need to
do these steps, so putting them as inline would save lot of code

This patch adds an inline to do list initialzation
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <harsha.priya@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The card debugfs initialization is done in soc_probe but would be better if it
is done when the card in registered

This patch moves the debugfs initialization to register_card()
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <harsha.priya@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In soc_remove() the card resources are cleaned up.
This can also be done in card_unregister()

This patch move this cleanup into a new function and calls it from
card_unregister. This paves way for further work to allow card registartion
from machine.
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

A recent discussion on linux-arm-kernel noted that the value returned by
clk_get_sys is an opaque token, and not strictly a pointer; it is
meaningful only to the clock API, clients should not dereference the value,
and the clock API must accept any non-IS_ERR value it returned.

Hence, only IS_ERR is appropriate to interpret the result, not
IS_ERR_OR_NULL.

I checked that clk_get_sys in both ASoC's for-next and Tegra's for-next
do behave as described; NULL is not returned in the case of error.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure that all calls to readable_register()/volatile_register() go via
the snd_soc_codec function pointers.

If the default register access table has been given but no functions
for handling readable()/volatile() registers, use the default ones provided
by soc-cache.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

For common scenarios, device drivers can provide a table of all the
registers that are at least either readable/writable/volatile.  The idea
is that if a register lookup fails, all of its read/write/vol members
will be zero and will be treated as default.  This also reduces the
size of the register access array.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>