Have the system reset idle wakeup handlers branched to in real mode
with the 0xc... kernel address applied. This allows simplifications of
avoiding rfid when switching to virtual mode in the wakeup handler.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

msgsnd doorbell exceptions are cleared when the doorbell interrupt is
taken. However if a doorbell exception causes a system reset interrupt
wake from power saving state, the message is not cleared. Processing
the doorbell from the system reset interrupt requires msgclr to avoid
taking the exception again.

Testing this plus the previous wakup direct patch gives:

                                original         wakeup direct     msgclr
Different threads, same core:   315k/s           264k/s            345k/s
Different cores:                235k/s           242k/s            242k/s

Net speedup is +10% for same core, and +3% for different core.
Reviewed-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When the CPU wakes from low power state, it begins at the system reset
interrupt with the exception that caused the wakeup encoded in SRR1.

Today, powernv idle wakeup ignores the wakeup reason (except a special
case for HMI), and the regular interrupt corresponding to the
exception will fire after the idle wakeup exits.

Change this to replay the interrupt from the idle wakeup before
interrupts are hard-enabled.

Test on POWER8 of context_switch selftests benchmark with polling idle
disabled (e.g., always nap, giving cross-CPU IPIs) gives the following
results:

                                original         wakeup direct
Different threads, same core:   315k/s           264k/s
Different cores:                235k/s           242k/s

There is a slowdown for doorbell IPI (same core) case because system
reset wakeup does not clear the message and the doorbell interrupt
fires again needlessly.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This simplifies the asm and fixes irq-off tracing over sleep
instructions.

Also move powersave_nap check for POWER8 into C code, and move
PSSCR register value calculation for POWER9 into C.
Reviewed-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The ISA v3.0B copy-paste facility only requires cpabort when switching
to a process that has foreign real addresses mapped (direct access to
accelerators), to clear a potential copy buffer filled by a previous
thread. There is no accelerator driver implemented yet, so cpabort can
be removed. It can be be re-added when a driver is implemented.

POWER9 DD1 requires the copy buffer to always be cleared on context
switch, but if accelerators are not in use, then an unpaired copy from
a dummy region is sufficient to clear data out of the copy buffer.

This increases context switch performance by about 5% on POWER9.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The sync (aka. hwsync, aka. heavyweight sync) in the context switch
code to prevent MMIO access being reordered from the point of view of
a single process if it gets migrated to a different CPU is not
required because there is an hwsync performed earlier in the context
switch path.

Comment this so it's clear enough if anything changes on the scheduler
or the powerpc sides. Remove the hwsync from _switch.

This improves context switch performance by 2-3% on POWER8.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The i-side 0111b machine check, which is "Instruction Fetch to foreign
address space", was missed by 7b9f71f9 ("powerpc/64s: POWER9 machine
check handler").

    The POWER9 processor core considers host real addresses with a
    nonzero value in RA(8:12) as foreign address space, accessible only
    by the copy and paste instructions. The copy and paste instruction
    pair can be used to invoke the Nest accelerators via the Virtual
    Accelerator Switchboard (VAS).

It is an error for any regular load/store or ifetch to go to a foreign
addresses. When relocation is on, this causes an MMU exception. When
relocation is off, a machine check exception. It is possible to trigger
this machine check by branching to a foreign address with MSR[IR]=0.

Fixes: 7b9f71f9 ("powerpc/64s: POWER9 machine check handler")
Reported-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

These two functions implement the same semantics, so unify their naming so we
can share code that calls them. The longer name is more descriptive so use it.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add support in pte_alloc_one() and pgd_alloc() by
passing __GFP_ACCOUNT in the flags
Signed-off-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Introduce a helper pgtable_gfp_flags() which
just returns the current gfp flags and adds
__GFP_ACCOUNT to account for page table allocation.
The generic helper is added to include/asm/pgalloc.h
and has two variants - WARNING ugly bits ahead

1. If the header is included from a module, no check
for mm == &init_mm is done, since init_mm is not
exported
2. For kernel includes, the check is done and required
see (3e79ec7d arch: x86: charge page tables to kmemcg)

The fundamental assumption is that no module should be
doing pgd/pud/pmd and pte alloc's on behalf of init_mm
directly.

NOTE: This adds an overhead to pmd/pud/pgd allocations
similar to x86.  The other alternative was to implement
pmd_alloc_kernel/pud_alloc_kernel and pgd_alloc_kernel
with their offset variants.

For 4k page size, pte_alloc_one no longer calls
pte_alloc_one_kernel.
Signed-off-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

By default, 5% of system RAM is reserved for preserving boot memory.
Alternatively, a user can specify the amount of memory to reserve.
See Documentation/powerpc/firmware-assisted-dump.txt for details. In
addition to the memory reserved for preserving boot memory, some more
memory is reserved, to save HPTE region, CPU state data and ELF core
headers.

Memory Reservation during first kernel looks like below:

  Low memory                                        Top of memory
  0      boot memory size                                       |
  |           |                       |<--Reserved dump area -->|
  V           V                       |   Permanent Reservation V
  +-----------+----------/ /----------+---+----+-----------+----+
  |           |                       |CPU|HPTE|  DUMP     |ELF |
  +-----------+----------/ /----------+---+----+-----------+----+
        |                                           ^
        |                                           |
        \                                           /
         -------------------------------------------
          Boot memory content gets transferred to
          reserved area by firmware at the time of
          crash

This implicitly means that the sum of the sizes of boot memory, CPU
state data, HPTE region, DUMP preserving area and ELF core headers
can't be greater than the total memory size. But currently, a user is
allowed to specify any value as boot memory size. So, the above rule
is violated when a boot memory size around 50% of the total available
memory is specified. As the kernel is not handling this currently, it
may lead to undefined behavior. Fix it by setting an upper limit for
boot memory size to 25% of the total available memory. Also, instead
of using memblock_end_of_DRAM(), which doesn't take the holes, if any,
in the memory layout into account, use memblock_phys_mem_size() to
calculate the percentage of total available memory.
Signed-off-by: NHari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

With the __ilog2() function as defined in
arch/powerpc/include/asm/bitops.h, GCC will not optimise the code
in case of constant parameter.

The generic ilog2() function in include/linux/log2.h is written
to handle the case of the constant parameter.

This patch discards the three __ilog2() functions and
defines __ilog2() as ilog2()

For non constant calls, the generated code is doing the same:
int test__ilog2(unsigned long x)
{
	return __ilog2(x);
}

int test__ilog2_u32(u32 n)
{
	return __ilog2_u32(n);
}

int test__ilog2_u64(u64 n)
{
	return __ilog2_u64(n);
}

On PPC32 before the patch:
00000000 <test__ilog2>:
   0:	7c 63 00 34 	cntlzw  r3,r3
   4:	20 63 00 1f 	subfic  r3,r3,31
   8:	4e 80 00 20 	blr

0000000c <test__ilog2_u32>:
   c:	7c 63 00 34 	cntlzw  r3,r3
  10:	20 63 00 1f 	subfic  r3,r3,31
  14:	4e 80 00 20 	blr

On PPC32 after the patch:
00000000 <test__ilog2>:
   0:	7c 63 00 34 	cntlzw  r3,r3
   4:	20 63 00 1f 	subfic  r3,r3,31
   8:	4e 80 00 20 	blr

0000000c <test__ilog2_u32>:
   c:	7c 63 00 34 	cntlzw  r3,r3
  10:	20 63 00 1f 	subfic  r3,r3,31
  14:	4e 80 00 20 	blr

On PPC64 before the patch:
0000000000000000 <.test__ilog2>:
   0:	7c 63 00 74 	cntlzd  r3,r3
   4:	20 63 00 3f 	subfic  r3,r3,63
   8:	7c 63 07 b4 	extsw   r3,r3
   c:	4e 80 00 20 	blr

0000000000000010 <.test__ilog2_u32>:
  10:	7c 63 00 34 	cntlzw  r3,r3
  14:	20 63 00 1f 	subfic  r3,r3,31
  18:	7c 63 07 b4 	extsw   r3,r3
  1c:	4e 80 00 20 	blr

0000000000000020 <.test__ilog2_u64>:
  20:	7c 63 00 74 	cntlzd  r3,r3
  24:	20 63 00 3f 	subfic  r3,r3,63
  28:	7c 63 07 b4 	extsw   r3,r3
  2c:	4e 80 00 20 	blr

On PPC64 after the patch:
0000000000000000 <.test__ilog2>:
   0:	7c 63 00 74 	cntlzd  r3,r3
   4:	20 63 00 3f 	subfic  r3,r3,63
   8:	7c 63 07 b4 	extsw   r3,r3
   c:	4e 80 00 20 	blr

0000000000000010 <.test__ilog2_u32>:
  10:	7c 63 00 34 	cntlzw  r3,r3
  14:	20 63 00 1f 	subfic  r3,r3,31
  18:	7c 63 07 b4 	extsw   r3,r3
  1c:	4e 80 00 20 	blr

0000000000000020 <.test__ilog2_u64>:
  20:	7c 63 00 74 	cntlzd  r3,r3
  24:	20 63 00 3f 	subfic  r3,r3,63
  28:	7c 63 07 b4 	extsw   r3,r3
  2c:	4e 80 00 20 	blr
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

With the ffz() function as defined in arch/powerpc/include/asm/bitops.h
GCC will not optimise the code in case of constant parameter.

This patch replaces ffz() by the generic function.

The generic ffz(x) expects to never be called with ~x == 0
as written in the comment in include/asm-generic/bitops/ffz.h
The only user of ffz() within arch/powerpc/ is
platforms/512x/mpc5121_ads_cpld.c, which checks if x is not 0xff

For non constant calls, the generated code is doing the same:

unsigned long testffz(unsigned long x)
{
	return ffz(x);
}

On PPC32, before the patch:
00000018 <testffz>:
  18:	7c 63 18 f9 	not.    r3,r3
  1c:	40 82 00 0c 	bne     28 <testffz+0x10>
  20:	38 60 00 20 	li      r3,32
  24:	4e 80 00 20 	blr
  28:	7d 23 00 d0 	neg     r9,r3
  2c:	7d 23 18 38 	and     r3,r9,r3
  30:	7c 63 00 34 	cntlzw  r3,r3
  34:	20 63 00 1f 	subfic  r3,r3,31
  38:	4e 80 00 20 	blr

On PPC32, after the patch:
00000018 <testffz>:
  18:	39 23 00 01 	addi    r9,r3,1
  1c:	7d 23 18 78 	andc    r3,r9,r3
  20:	7c 63 00 34 	cntlzw  r3,r3
  24:	20 63 00 1f 	subfic  r3,r3,31
  28:	4e 80 00 20 	blr

On PPC64, before the patch:
0000000000000030 <.testffz>:
  30:	7c 60 18 f9 	not.    r0,r3
  34:	38 60 00 40 	li      r3,64
  38:	4d 82 00 20 	beqlr
  3c:	7c 60 00 d0 	neg     r3,r0
  40:	7c 63 00 38 	and     r3,r3,r0
  44:	7c 63 00 74 	cntlzd  r3,r3
  48:	20 63 00 3f 	subfic  r3,r3,63
  4c:	7c 63 07 b4 	extsw   r3,r3
  50:	4e 80 00 20 	blr

On PPC64, after the patch:
0000000000000030 <.testffz>:
  30:	38 03 00 01 	addi    r0,r3,1
  34:	7c 03 18 78 	andc    r3,r0,r3
  38:	7c 63 00 74 	cntlzd  r3,r3
  3c:	20 63 00 3f 	subfic  r3,r3,63
  40:	4e 80 00 20 	blr
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

With the fls() functions as defined in arch/powerpc/include/asm/bitops.h
GCC will not optimise the code in case of constant parameter.

This patch replaces __fls() by the builtin function, and modifies
fls() and fls64() to use builtins instead of inline assembly

For non constant calls, the generated code is doing the same:

int testfls(unsigned int x)
{
	return fls(x);
}

unsigned long test__fls(unsigned long x)
{
	return __fls(x);
}

int testfls64(__u64 x)
{
	return fls64(x);
}

On PPC32, before the patch:
00000064 <testfls>:
  64:	7c 63 00 34 	cntlzw  r3,r3
  68:	20 63 00 20 	subfic  r3,r3,32
  6c:	4e 80 00 20 	blr

00000070 <test__fls>:
  70:	7c 63 00 34 	cntlzw  r3,r3
  74:	20 63 00 1f 	subfic  r3,r3,31
  78:	4e 80 00 20 	blr

0000007c <testfls64>:
  7c:	2c 03 00 00 	cmpwi   r3,0
  80:	40 82 00 10 	bne     90 <testfls64+0x14>
  84:	7c 83 00 34 	cntlzw  r3,r4
  88:	20 63 00 20 	subfic  r3,r3,32
  8c:	4e 80 00 20 	blr
  90:	7c 63 00 34 	cntlzw  r3,r3
  94:	20 63 00 40 	subfic  r3,r3,64
  98:	4e 80 00 20 	blr

On PPC32, after the patch:
00000054 <testfls>:
  54:	7c 63 00 34 	cntlzw  r3,r3
  58:	20 63 00 20 	subfic  r3,r3,32
  5c:	4e 80 00 20 	blr

00000060 <test__fls>:
  60:	7c 63 00 34 	cntlzw  r3,r3
  64:	20 63 00 1f 	subfic  r3,r3,31
  68:	4e 80 00 20 	blr

0000006c <testfls64>:
  6c:	2c 03 00 00 	cmpwi   r3,0
  70:	41 82 00 10 	beq     80 <testfls64+0x14>
  74:	7c 63 00 34 	cntlzw  r3,r3
  78:	20 63 00 40 	subfic  r3,r3,64
  7c:	4e 80 00 20 	blr
  80:	7c 83 00 34 	cntlzw  r3,r4
  84:	20 63 00 40 	subfic  r3,r3,32
  88:	4e 80 00 20 	blr

On PPC64, before the patch:
00000000000000a0 <.testfls>:
  a0:	7c 63 00 34 	cntlzw  r3,r3
  a4:	20 63 00 20 	subfic  r3,r3,32
  a8:	7c 63 07 b4 	extsw   r3,r3
  ac:	4e 80 00 20 	blr

00000000000000b0 <.test__fls>:
  b0:	7c 63 00 74 	cntlzd  r3,r3
  b4:	20 63 00 3f 	subfic  r3,r3,63
  b8:	7c 63 07 b4 	extsw   r3,r3
  bc:	4e 80 00 20 	blr

00000000000000c0 <.testfls64>:
  c0:	7c 63 00 74 	cntlzd  r3,r3
  c4:	20 63 00 40 	subfic  r3,r3,64
  c8:	7c 63 07 b4 	extsw   r3,r3
  cc:	4e 80 00 20 	blr

On PPC64, after the patch:
0000000000000090 <.testfls>:
  90:	7c 63 00 34 	cntlzw  r3,r3
  94:	20 63 00 20 	subfic  r3,r3,32
  98:	7c 63 07 b4 	extsw   r3,r3
  9c:	4e 80 00 20 	blr

00000000000000a0 <.test__fls>:
  a0:	7c 63 00 74 	cntlzd  r3,r3
  a4:	20 63 00 3f 	subfic  r3,r3,63
  a8:	4e 80 00 20 	blr
  ac:	60 00 00 00 	nop

00000000000000b0 <.testfls64>:
  b0:	7c 63 00 74 	cntlzd  r3,r3
  b4:	20 63 00 40 	subfic  r3,r3,64
  b8:	7c 63 07 b4 	extsw   r3,r3
  bc:	4e 80 00 20 	blr

Those builtins have been in GCC since at least 3.4.6 (see
https://gcc.gnu.org/onlinedocs/gcc-3.4.6/gcc/Other-Builtins.html )
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

With the ffs() function as defined in arch/powerpc/include/asm/bitops.h
GCC will not optimise the code in case of constant parameter, as shown
by the small exemple below.

int ffs_test(void)
{
	return 4 << ffs(31);
}

c0012334 <ffs_test>:
c0012334:       39 20 00 01     li      r9,1
c0012338:       38 60 00 04     li      r3,4
c001233c:       7d 29 00 34     cntlzw  r9,r9
c0012340:       21 29 00 20     subfic  r9,r9,32
c0012344:       7c 63 48 30     slw     r3,r3,r9
c0012348:       4e 80 00 20     blr

With this patch, the same function will compile as follows:

c0012334 <ffs_test>:
c0012334:       38 60 00 08     li      r3,8
c0012338:       4e 80 00 20     blr

The same happens with __ffs()

For non constant calls, the generated code is doing the same,
allthought it is slightly different on 64 bits for ffs():

unsigned long test__ffs(unsigned long x)
{
	return __ffs(x);
}

int testffs(int x)
{
	return ffs(x);
}

On PPC32, before the patch:
0000003c <test__ffs>:
  3c:	7d 23 00 d0 	neg     r9,r3
  40:	7d 23 18 38 	and     r3,r9,r3
  44:	7c 63 00 34 	cntlzw  r3,r3
  48:	20 63 00 1f 	subfic  r3,r3,31
  4c:	4e 80 00 20 	blr

00000050 <testffs>:
  50:	7d 23 00 d0 	neg     r9,r3
  54:	7d 23 18 38 	and     r3,r9,r3
  58:	7c 63 00 34 	cntlzw  r3,r3
  5c:	20 63 00 20 	subfic  r3,r3,32
  60:	4e 80 00 20 	blr

On PPC32, after the patch:
0000002c <test__ffs>:
  2c:	7d 23 00 d0 	neg     r9,r3
  30:	7d 23 18 38 	and     r3,r9,r3
  34:	7c 63 00 34 	cntlzw  r3,r3
  38:	20 63 00 1f 	subfic  r3,r3,31
  3c:	4e 80 00 20 	blr

00000040 <testffs>:
  40:	7d 23 00 d0 	neg     r9,r3
  44:	7d 23 18 38 	and     r3,r9,r3
  48:	7c 63 00 34 	cntlzw  r3,r3
  4c:	20 63 00 20 	subfic  r3,r3,32
  50:	4e 80 00 20 	blr

On PPC64, before the patch:
0000000000000060 <.test__ffs>:
  60:	7c 03 00 d0 	neg     r0,r3
  64:	7c 03 18 38 	and     r3,r0,r3
  68:	7c 63 00 74 	cntlzd  r3,r3
  6c:	20 63 00 3f 	subfic  r3,r3,63
  70:	7c 63 07 b4 	extsw   r3,r3
  74:	4e 80 00 20 	blr

0000000000000080 <.testffs>:
  80:	7c 03 00 d0 	neg     r0,r3
  84:	7c 03 18 38 	and     r3,r0,r3
  88:	7c 63 00 74 	cntlzd  r3,r3
  8c:	20 63 00 40 	subfic  r3,r3,64
  90:	7c 63 07 b4 	extsw   r3,r3
  94:	4e 80 00 20 	blr

On PPC64, after the patch:
0000000000000050 <.test__ffs>:
  50:	7c 03 00 d0 	neg     r0,r3
  54:	7c 03 18 38 	and     r3,r0,r3
  58:	7c 63 00 74 	cntlzd  r3,r3
  5c:	20 63 00 3f 	subfic  r3,r3,63
  60:	4e 80 00 20 	blr

0000000000000070 <.testffs>:
  70:	7c 03 00 d0 	neg     r0,r3
  74:	7c 03 18 38 	and     r3,r0,r3
  78:	7c 63 00 34 	cntlzw  r3,r3
  7c:	20 63 00 20 	subfic  r3,r3,32
  80:	7c 63 07 b4 	extsw   r3,r3
  84:	4e 80 00 20 	blr
(ffs() operates on an int so cntlzw is equivalent to cntlzd)

In addition, when reading the generated vmlinux, we can observe
that with the builtin functions, GCC sometimes efficiently spreads
the instructions within the generated functions while the inline
assembly force them to remain grouped together.

__builtin_ffs() is already used in arch/powerpc/include/asm/page_32.h

Those builtins have been in GCC since at least 3.4.6 (see
https://gcc.gnu.org/onlinedocs/gcc-3.4.6/gcc/Other-Builtins.html )
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Use a tool to check that the location of "fixed sections" are where
we expected them to be, which catches cases the linker script can't
(stubs being added to start of .text section), and which ends up
being neater.

Sample output:

  ERROR: start_text address is c000000000008100, should be c000000000008000
  ERROR: see comments in arch/powerpc/tools/head_check.sh
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
[mpe: Fold in fix from Nick for 4.6 era toolchains]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Very large kernels may require linker stubs for branches from HEAD
text code. The linker may place these stubs before the HEAD text
sections, which breaks the assumption that HEAD text is located at 0
(or the .text section being located at 0x7000/0x8000 on Book3S
kernels).

Provide an option to create a small section just before the .text
section with an empty 256 - 4 bytes, and adjust the start of the .text
section to match. The linker will tend to put stubs in that section
and not break our relative-to-absolute offset assumptions.

This causes a small waste of space on common kernels, but allows large
kernels to build and boot. For now, it is an EXPERT config option,
defaulting to =n, but a reference is provided for it in the build-time
check for such breakage. This is good enough for allyesconfig and
custom users / hackers.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The arch version is identical except for comments and white space.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

These are completely obvious as all they do is include the asm-generic
versions.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

On Power9 DD1 due to a hardware bug the Power-Saving Level Status
field (PLS) of the PSSCR for a thread waking up from a deep state can
under-report if some other thread in the core is in a shallow stop
state. The scenario in which this can manifest is as follows:

   1) All the threads of the core are in deep stop.
   2) One of the threads is woken up. The PLS for this thread will
      correctly reflect that it is waking up from deep stop.
   3) The thread that has woken up now executes a shallow stop.
   4) When some other thread in the core is woken, its PLS will reflect
      the shallow stop state.

Thus, the subsequent thread for which the PLS is under-reporting the
wakeup state will not restore the hypervisor resources.

Hence, on DD1 systems, use the Requested Level (RL) field as a
workaround to restore the contents of the hypervisor resources on the
wakeup from the stop state.
Signed-off-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

FIXUP_ENDIAN uses SRR[01] with MSR_RI=1, which gets corrupted if there
is an interleaving system reset or machine check interrupt.

Set MSR_RI=0 before setting SRRs. The rfid will restore MSR.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Providing "scv" support to userspace requires kernel support, so it
must be advertised as independently to the base ISA 3 instruction set.

The darn instruction relies on firmware enablement, so it has been
decided to split this out from the core ISA 3 feature as well.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

virt_addr_valid() is supposed to tell you if it's OK to call virt_to_page() on
an address. What this means in practice is that it should only return true for
addresses in the linear mapping which are backed by a valid PFN.

We are failing to properly check that the address is in the linear mapping,
because virt_to_pfn() will return a valid looking PFN for more or less any
address. That bug is actually caused by __pa(), used in virt_to_pfn().

eg: __pa(0xc000000000010000) = 0x10000  # Good
    __pa(0xd000000000010000) = 0x10000  # Bad!
    __pa(0x0000000000010000) = 0x10000  # Bad!

This started happening after commit bdbc29c1 ("powerpc: Work around gcc
miscompilation of __pa() on 64-bit") (Aug 2013), where we changed the definition
of __pa() to work around a GCC bug. Prior to that we subtracted PAGE_OFFSET from
the value passed to __pa(), meaning __pa() of a 0xd or 0x0 address would give
you something bogus back.

Until we can verify if that GCC bug is no longer an issue, or come up with
another solution, this commit does the minimal fix to make virt_addr_valid()
work, by explicitly checking that the address is in the linear mapping region.

Fixes: bdbc29c1 ("powerpc: Work around gcc miscompilation of __pa() on 64-bit")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Reviewed-by: NPaul Mackerras <paulus@ozlabs.org>
Reviewed-by: NBalbir Singh <bsingharora@gmail.com>
Tested-by: NBreno Leitao <breno.leitao@gmail.com>

On powerpc we can build the kernel with two different ABIs for mcount(), which
is used by ftrace. Kernels built with one ABI do not know how to load modules
built with the other ABI. The new style ABI is called "mprofile-kernel", for
want of a better name.

Currently if we build a module using the old style ABI, and the kernel with
mprofile-kernel, when we load the module we'll oops something like:

  # insmod autofs4-no-mprofile-kernel.ko
  ftrace-powerpc: Unexpected instruction f8810028 around bl _mcount
  ------------[ cut here ]------------
  WARNING: CPU: 6 PID: 3759 at ../kernel/trace/ftrace.c:2024 ftrace_bug+0x2b8/0x3c0
  CPU: 6 PID: 3759 Comm: insmod Not tainted 4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74 #11
  ...
  NIP [c0000000001eaa48] ftrace_bug+0x2b8/0x3c0
  LR [c0000000001eaff8] ftrace_process_locs+0x4a8/0x590
  Call Trace:
    alloc_pages_current+0xc4/0x1d0 (unreliable)
    ftrace_process_locs+0x4a8/0x590
    load_module+0x1c8c/0x28f0
    SyS_finit_module+0x110/0x140
    system_call+0x38/0xfc
  ...
  ftrace failed to modify
  [<d000000002a31024>] 0xd000000002a31024
   actual:   35:65:00:48

We can avoid this by including in the vermagic whether the kernel/module was
built with mprofile-kernel. Which results in:

  # insmod autofs4-pg.ko
  autofs4: version magic
  '4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74 SMP mod_unload modversions '
  should be
  '4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74-dirty SMP mod_unload modversions mprofile-kernel'
  insmod: ERROR: could not insert module autofs4-pg.ko: Invalid module format

Fixes: 8c50b72a ("powerpc/ftrace: Add Kconfig & Make glue for mprofile-kernel")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Acked-by: NJessica Yu <jeyu@redhat.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Regularly, when a new header is created in include/uapi/, the developer
forgets to add it in the corresponding Kbuild file. This error is usually
detected after the release is out.

In fact, all headers under uapi directories should be exported, thus it's
useless to have an exhaustive list.

After this patch, the following files, which were not exported, are now
exported (with make headers_install_all):
asm-arc/kvm_para.h
asm-arc/ucontext.h
asm-blackfin/shmparam.h
asm-blackfin/ucontext.h
asm-c6x/shmparam.h
asm-c6x/ucontext.h
asm-cris/kvm_para.h
asm-h8300/shmparam.h
asm-h8300/ucontext.h
asm-hexagon/shmparam.h
asm-m32r/kvm_para.h
asm-m68k/kvm_para.h
asm-m68k/shmparam.h
asm-metag/kvm_para.h
asm-metag/shmparam.h
asm-metag/ucontext.h
asm-mips/hwcap.h
asm-mips/reg.h
asm-mips/ucontext.h
asm-nios2/kvm_para.h
asm-nios2/ucontext.h
asm-openrisc/shmparam.h
asm-parisc/kvm_para.h
asm-powerpc/perf_regs.h
asm-sh/kvm_para.h
asm-sh/ucontext.h
asm-tile/shmparam.h
asm-unicore32/shmparam.h
asm-unicore32/ucontext.h
asm-x86/hwcap2.h
asm-xtensa/kvm_para.h
drm/armada_drm.h
drm/etnaviv_drm.h
drm/vgem_drm.h
linux/aspeed-lpc-ctrl.h
linux/auto_dev-ioctl.h
linux/bcache.h
linux/btrfs_tree.h
linux/can/vxcan.h
linux/cifs/cifs_mount.h
linux/coresight-stm.h
linux/cryptouser.h
linux/fsmap.h
linux/genwqe/genwqe_card.h
linux/hash_info.h
linux/kcm.h
linux/kcov.h
linux/kfd_ioctl.h
linux/lightnvm.h
linux/module.h
linux/nbd-netlink.h
linux/nilfs2_api.h
linux/nilfs2_ondisk.h
linux/nsfs.h
linux/pr.h
linux/qrtr.h
linux/rpmsg.h
linux/sched/types.h
linux/sed-opal.h
linux/smc.h
linux/smc_diag.h
linux/stm.h
linux/switchtec_ioctl.h
linux/vfio_ccw.h
linux/wil6210_uapi.h
rdma/bnxt_re-abi.h

Note that I have removed from this list the files which are generated in every
exported directories (like .install or .install.cmd).

Thanks to Julien Floret <julien.floret@6wind.com> for the tip to get all
subdirs with a pure makefile command.

For the record, note that exported files for asm directories are a mix of
files listed by:
 - include/uapi/asm-generic/Kbuild.asm;
 - arch/<arch>/include/uapi/asm/Kbuild;
 - arch/<arch>/include/asm/Kbuild.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Acked-by: NMark Salter <msalter@redhat.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

The ibm,powerpc-cpu-features device tree binding describes CPU features with
ASCII names and extensible compatibility, privilege, and enablement metadata
that allows improved flexibility and compatibility with new hardware.

The interface is described in detail in ibm,powerpc-cpu-features.txt in this
patch.

Currently this code is not enabled by default, and there are no released
firmwares that provide the binding.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Recently in commit f6eedbba ("powerpc/mm/hash: Increase VA range to 128TB")
we increased the virtual address space for user processes to 128TB by default,
and up to 512TB if user space opts in.

This obviously required expanding the range of the Linux page tables. For Book3s
64-bit using hash and with PAGE_SIZE=64K, we increased the PGD to 2^15 entries.
This meant we could cover the full address range, while still being able to
insert a 16G hugepage at the PGD level and a 16M hugepage in the PMD.

The downside of that geometry is that it uses a lot of memory for the PGD, and
in particular makes the PGD a 4-page allocation, which means it's much more
likely to fail under memory pressure.

Instead we can make the PMD larger, so that a single PUD entry maps 16G,
allowing the 16G hugepages to sit at that level in the tree. We're then able to
split the remaining bits between the PUG and PGD. We make the PGD slightly
larger as that results in lower memory usage for typical programs.

When THP is enabled the PMD actually doubles in size, to 2^11 entries, or 2^14
bytes, which is large but still < PAGE_SIZE.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Reviewed-by: NBalbir Singh <bsingharora@gmail.com>
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>

Now that crashkernel parameter parsing and vmcoreinfo related code is
moved under CONFIG_CRASH_CORE instead of CONFIG_KEXEC_CORE, remove
dependency with CONFIG_KEXEC for CONFIG_FA_DUMP.  While here, get rid of
definitions of fadump_append_elf_note() & fadump_final_note() functions
to reuse similar functions compiled under CONFIG_CRASH_CORE.

Link: http://lkml.kernel.org/r/149035343956.6881.1536459326017709354.stgit@hbathini.in.ibm.comSigned-off-by: NHari Bathini <hbathini@linux.vnet.ibm.com>
Reviewed-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit f4ea6dcb ("powerpc/mm: Enable mappings above 128TB") increased
the task size on book3s, and introduced a mechanism to dynamically
control whether a task uses these larger addresses.  While the change to
the task size itself was ifdef-protected to only apply on book3s, the
change to STACK_TOP_USER64 was not.  On book3e, this had the effect of
trying to use addresses up to 128TiB for the stack despite a 64TiB task
size limit -- which broke 64-bit userspace producing the following errors:

Starting init: /sbin/init exists but couldn't execute it (error -14)
Starting init: /bin/sh exists but couldn't execute it (error -14)
Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/admin-guide/init.rst for guidance.

Fixes: f4ea6dcb ("powerpc/mm: Enable mappings above 128TB")
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NScott Wood <oss@buserror.net>

This patch allows the use of IRQ to notify the change of GPIO status
on MPC8xx CPM IO ports. This then allows to associate IRQs to GPIOs
in the Device Tree.

Ex:
	CPM1_PIO_C: gpio-controller@960 {
		#gpio-cells = <2>;
		compatible = "fsl,cpm1-pario-bank-c";
		reg = <0x960 0x10>;
		fsl,cpm1-gpio-irq-mask = <0x0fff>;
		interrupts = <1 2 6 9 10 11 14 15 23 24 26 31>;
		interrupt-parent = <&CPM_PIC>;
		gpio-controller;
	};

The property 'fsl,cpm1-gpio-irq-mask' defines which of the 16 GPIOs
have the associated interrupts defined in the 'interrupts' property.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NScott Wood <oss@buserror.net>

Michal Suchánek noticed a comment in book3s/64/mmu-hash.h about the context ids
we use for the kernel was inconsistent with the code and other comments in the
same file.

It should read 1-4 not 1-5.

While we're touching it, update "address" to "addresses" which makes more sense
as it's referring to more than one address below.
Reported-by: NMichal Suchánek <msuchanek@suse.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Have the NMI IPI code use this op when the platform defines it.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add a simple NMI IPI system that handles concurrency and reentrancy.

The platform does not have to implement a true non-maskable interrupt,
the default is to simply use the debugger break IPI message. This has
now been co-opted for a general IPI message, and users (debugger and
crash) have been reimplemented on top of the NMI system.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
[mpe: Incorporate incremental fixes from Nick]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The system reset interrupt is used for crash/debug situations, so it is
desirable to have as little impact on the normal state of the system as
possible.

Currently it uses the current kernel stack to process the exception.
This stores into the stack which may be involved with the crash. The
stack pointer may be corrupted, or it may have overflowed.

Avoid or minimise these problems by creating a dedicated NMI stack for
the system reset interrupt to use.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In preparation for using a dedicated stack for system reset interrupts,
prevent a nested system reset from recovering, in order to simplify
code that is called in crash/debug path. This allows a system reset
interrupt to just use the base stack pointer.

Keep an in_nmi nesting counter similarly to the in_mce counter. Consider
the interrrupt non-recoverable if it is taken inside another system
reset.

Interrupt nesting could be allowed similarly to MCE, but system reset
is a special case that's not for normal operation, so simplicity wins
until there is requirement for nested system reset interrupts.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The system reset interrupt can occur when MSR_EE=0, and it currently
uses the PACA_EXGEN save area.

Some PACA_EXGEN interrupts have a window where MSR_RI=1 and MSR_EE=0
when the save area is still in use. A system reset interrupt in this
window can lead to undetected corruption when the save area gets
overwritten.

This patch introduces PACA_EXNMI save area for system reset exceptions,
which closes this corruption window. It's also helpful to retain the
EXGEN state for debugging situations, even if not considering the
recoverability aspect.

This patch also moves the PACA_EXMC area down to a less frequently used
part of the paca with the new save area.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This code is common to a few exceptions, and another user will be added.
This causes a trivial change to generated code:

-     604: std     r9,416(r1)
-     608: mfspr   r11,314
-     60c: std     r11,368(r1)
-     610: mfspr   r12,315
+     604: mfspr   r11,314
+     608: mfspr   r12,315
+     60c: std     r9,416(r1)
+     610: std     r11,368(r1)

machine_check_powernv_early could also use this, but that requires non
trivial changes to generated code, so that's for another patch.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Subsequent patches will add more non-RI variant exceptions, so
create a macro for it rather than open-code it.

This does not change generated instructions.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

On some targets, _PAGE_RW is 0 and this is _PAGE_RO which is used.
There is also _PAGE_SHARED that is missing.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch makes KVM capable of using the XIVE interrupt controller
to provide the standard PAPR "XICS" style hypercalls. It is necessary
for proper operations when the host uses XIVE natively.

This has been lightly tested on an actual system, including PCI
pass-through with a TG3 device.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Cleanup pr_xxx(), unsplit pr_xxx() strings, etc., fix build
 failures by adding KVM_XIVE which depends on KVM_XICS and XIVE, and
 adding empty stubs for the kvm_xive_xxx() routines, fixup subject,
 integrate fixes from Paul for building PR=y HV=n]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>