Add Runtime PM support to C_CAN/D_CAN controller. The runtime PM
APIs control clocks for C_CAN/D_CAN IP and prevent access to the
register of C_CAN/D_CAN IP when clock is turned off.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Modify c_can device names from *_CAN_DEVTYPE to BOSCH_*_CAN to make
use of same names for array indexes in c_can_id_table[] as well as
device names.

This patch also add indexes to c_can_id_table array.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds the support for D_CAN controller driver to the existing
C_CAN driver.

Bosch D_CAN controller is a full-CAN implementation which is compliant
to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be
obtained from: http://www.semiconductors.bosch.de/media/en/pdf/
ipmodules_1/can/d_can_users_manual_111.pdf

A new array is added for accessing the d_can registers, according to d_can
controller register space.

Current D_CAN implementation has following limitations, this is done
to avoid large changes to the C_CAN driver.
1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP
   supports upto 32 message objects but in case of D_CAN we can configure
   upto 128 message objects.
2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers.
3. These patches have been tested on little endian machine, there might
   be some hidden endian-related issues due to the nature of the accesses
   (32-bit registers accessed as 2 16-bit registers). However, I do not
   have a big-endian D_CAN implementation to confirm.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

c_can uses overlay structure for accessing c_can module registers.
With this kind of implementation it is difficult to add one more ip
which is similar to c_can in functionality but different register
offsets.

This patch changes the overlay structure implementation to an array
with register offset as index. This way we can overcome the above
limitation.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch fixes an interrupt thrash issue with c_can driver.

In c_can_isr() function interrupts are disabled and enabled only in
c_can_poll() function. c_can_isr() & c_can_poll() both read the
irqstatus flag. However, irqstatus is always read as 0 in c_can_poll()
because all C_CAN interrupts are disabled in c_can_isr(). This causes
all interrupts to be re-enabled in c_can_poll() which in turn causes
another interrupt since the event is not really handled. This keeps
happening causing a flood of interrupts.

To fix this, read the irqstatus register in isr and use the same cached
value in the poll function.

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Bosch C_CAN controller is a full-CAN implementation which is compliant
to CAN protocol version 2.0 part A and B. Bosch C_CAN user manual can be
obtained from:

http://www.semiconductors.bosch.de/media/en/pdf/ipmodules_1/c_can/users_manual_c_can.pdf

This patch adds the support for this controller.
The following are the design choices made while writing the controller
driver:
1. Interface Register set IF1 has be used only in the current design.
2. Out of the 32 Message objects available, 16 are kept aside for RX
   purposes and the rest for TX purposes.
3. NAPI implementation is such that both the TX and RX paths function
   in polling mode.
Signed-off-by: NBhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>