Add missing mac80211 callbacks to mt76x0e_ops data structure
and add mt76x02_beacon utility routines in mt76x0_bss_info_changed
in order to enable/disable beacon transmission
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Add mt76x02_init_beacon_config utility routine in mt76x02-lib
module in order to be reused by mt76x0 driver configuring
BSSID registers and remove duplicated code
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_sta_ps utility routine in mt76x02_util.c
in order to be reused by mt76x0 driver adding AP support
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_get_txpower utility routine in mt76x02-lib module
in order to be reused by mt76x0 and mt76x2u drivers
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_sw_scan and mt76x02_sw_scan_complete utility routines
in mt76x02_util.c in order to be reused by mt76x0 and mt76x2u drivers
and remove duplicated code
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Enable/disable pre_tbtt_tasklet in mt76x0 driver in order
to add AP support
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_tx beacon utility routines in mt76x02_mmio.c
in order to be reused by mt76x0 driver adding AP support
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_beacon mac routines in mt76x02_mac.c in
order to be reused by mt76x0 driver adding AP support
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_init_device routine in mt76x02_util.c in order to be
reused by mt76x0 driver and remove duplicated code. Move interface
combo definition supported by the driver in mt76x02_init_device routine
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_mac_set_short_preamble routine in mt76x02-lib module
since it is shared between mt76x0 and mt76x2 drivers
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Unify firmware version used on mt76x0e and mt76x0u drivers.
Fallback to mt7610u fw if mt7610e one is not available
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Remove no longer used mt76x0_mac_set_ampdu_factor routine
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Add missing firmware declaration for mt76x0e driver
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Simplify mt76x0_init_mac_registers routine using mt76_set, mt76_clear
and mt76_rmw utility routines
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Update mt76x0_phy_ant_select() to conform vendor driver, most notably
add dual antenna mode support, read configuration from EEPROM and
move ant select out of channel config to init phase. Plus small MT7630E
quirk for MT_CMB_CTRL register which vendor driver dedicated to this
chip do.

This make MT7630E workable with mt76x0e driver and do not cause any
problems on MT7610U for me.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Add submit_urb and rx_urb static tracepoints in mt76-usb module.
Move trace_mac_txstat_fetch in mt76x02_mac_load_tx_status routine
in order to be available to usb drivers. Moreover remove
no longer used mt76x0/trace.{c,h}
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Some RF registers need different values for various chips.
For at least mt76x0_rf_central_tab registers, overwriting them later does
not work, as the wrong values can cause the entire system to hang on some
devices with MT7610E
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Make previously exported functions static where possible
Acked-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Driver works better for MT7630 without MCU calibration, which
looks like it can hangs the firmware. Vendor driver do not
perform it for MT7630 as well.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Align phy calibration logic between mt76x0u and mt76x0e drivers
This patch improves connection stability with low SNR
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Add mac workqueue support to mt76x2u driver in order
to compute device statistics and add mac stuck routine
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Use mt76x02_mac_work utility routine as stats workqueue handler
and remove duplicated code. Moreover run mac stuck check in
mt76x02_mac_work for client interfaces.
Remove no longer used avg_ampdu_len and mt76x02_mac_stats data
structure in mt76x02_dev
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Use mt76x02 debugfs implementation and remove duplicated code
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_debugfs in mt76x02-lib module in order to
be reused by mt76x0 driver and remove duplicated code
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_mac_work routine in mt76x02_mac.c in order to be reused by
mt76x0 driver to read device statistics
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_update_channel routine in mt76x02-lib module in
order to be reused by mt76x0 driver adding get_survey support
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Improve initvals_phy.h code readability (there are no actual changes
of original values)
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Simplify mt76x0_phy_vco_cal and mt76x0_phy_set_chan_rf_params
routines using mt76x0_rf_wr, mt76x0_rf_set and mt76x0_rf_clear
helper routines. Moreover over get rid of magic numbers
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Use mt76x0_phy as prefix for routines in mt76x0/phy.c
Moreover use mt76x0_rf_set to enable vco calibration in
mt76x0_phy_vco_cal
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Update vga tuning algorithm to the one used in mt76x2 driver
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Unify firmware version used on mt76x2e and mt76x2u drivers
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

I ended up tracking down some rather nasty issues with f2fs (and other
filesystem modules) constantly crashing on my kernel down to a
combination of out of bounds memory accesses, one of which was coming
from brcmfmac during module load:

[   30.891382] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[   30.894437] ==================================================================
[   30.901581] BUG: KASAN: global-out-of-bounds in brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[   30.909935] Read of size 1 at addr ffff2000024865df by task kworker/6:2/387
[   30.916805]
[   30.918261] CPU: 6 PID: 387 Comm: kworker/6:2 Tainted: G           O      4.20.0-rc3Lyude-Test+ #19
[   30.927251] Hardware name: amlogic khadas-vim2/khadas-vim2, BIOS 2018.07-rc2-armbian 09/11/2018
[   30.935964] Workqueue: events brcmf_driver_register [brcmfmac]
[   30.941641] Call trace:
[   30.944058]  dump_backtrace+0x0/0x3e8
[   30.947676]  show_stack+0x14/0x20
[   30.950968]  dump_stack+0x130/0x1c4
[   30.954406]  print_address_description+0x60/0x25c
[   30.959066]  kasan_report+0x1b4/0x368
[   30.962683]  __asan_report_load1_noabort+0x18/0x20
[   30.967547]  brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[   30.967639]  brcmf_sdio_probe+0x163c/0x2050 [brcmfmac]
[   30.978035]  brcmf_ops_sdio_probe+0x598/0xa08 [brcmfmac]
[   30.983254]  sdio_bus_probe+0x190/0x398
[   30.983270]  really_probe+0x2a0/0xa70
[   30.983296]  driver_probe_device+0x1b4/0x2d8
[   30.994901]  __driver_attach+0x200/0x280
[   30.994914]  bus_for_each_dev+0x10c/0x1a8
[   30.994925]  driver_attach+0x38/0x50
[   30.994935]  bus_add_driver+0x330/0x608
[   30.994953]  driver_register+0x140/0x388
[   31.013965]  sdio_register_driver+0x74/0xa0
[   31.014076]  brcmf_sdio_register+0x14/0x60 [brcmfmac]
[   31.023177]  brcmf_driver_register+0xc/0x18 [brcmfmac]
[   31.023209]  process_one_work+0x654/0x1080
[   31.032266]  worker_thread+0x4f0/0x1308
[   31.032286]  kthread+0x2a8/0x320
[   31.039254]  ret_from_fork+0x10/0x1c
[   31.039269]
[   31.044226] The buggy address belongs to the variable:
[   31.044351]  brcmf_firmware_path+0x11f/0xfffffffffffd3b40 [brcmfmac]
[   31.055601]
[   31.057031] Memory state around the buggy address:
[   31.061800]  ffff200002486480: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
[   31.068983]  ffff200002486500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   31.068993] >ffff200002486580: 00 00 00 00 00 00 00 00 fa fa fa fa 00 00 00 00
[   31.068999]                                                     ^
[   31.069017]  ffff200002486600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[   31.096521]  ffff200002486680: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
[   31.096528] ==================================================================
[   31.096533] Disabling lock debugging due to kernel taint

It appears that when trying to determine the length of the string in the
alternate firmware path, we make the mistake of not handling the case
where the firmware path is empty correctly. Since strlen(mp_path) can
return 0, we'll end up accessing mp_path[-1] when the firmware_path
isn't provided through the module arguments.

So, fix this by just setting the end char to '\0' by default, and only
changing it if we have a non-zero length. Additionally, use strnlen()
with BRCMF_FW_ALTPATH_LEN instead of strlen() just to be extra safe.

Fixes: 2baa3aae ("brcmfmac: introduce brcmf_fw_alloc_request() function")
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Himanshu Jha <himanshujha199640@gmail.com>
Cc: Dan Haab <dhaab@luxul.com>
Cc: Jia-Shyr Chuang <saint.chuang@cypress.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ARM systems with UEFI may have both devicetree (of) and DMI data in this
case we end up setting brcmf_mp_device.board_type twice.

In this case we should prefer the devicetree data, because:
1) The devicerree data is more reliable
2) Some ARM systems (e.g. the Raspberry Pi 3 models) support both UEFI and
   classic uboot booting, the devicetree data is always there, so using it
   makes sure we ask for the same nvram file independent of how we booted.

This commit moves the brcmf_dmi_probe call to before the brcmf_of_probe
call, so that the latter can override the value of the first if both are
set.

Fixes: bd1e82bb ("brcmfmac: Set board_type from DMI on x86 based ...")
Cc: Peter Robinson <pbrobinson@gmail.com>
Tested-and-reported-by: NPeter Robinson <pbrobinson@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The newest firmwares provide STA info using v7 of the struct. As v7
isn't backward compatible, a union is needed.

Even though brcmfmac does not use any of the new info it's important to
provide the proper struct buffer. Without this change new firmwares will
fallback to the very limited v3 instead of something in between such as
v4.
Signed-off-by: NDan Haab <dan.haab@luxul.com>
Reviewed-by: NRafał Miłecki <rafal@milecki.pl>
Reviewed-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Kernel library has a common cordic algorithm which is identical
to internally implemented one, so use it and drop the duplicate
implementation.
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The cordic routine for calculating sines and cosines that was added in
commit 6f98e62a ("b43: update cordic code to match current specs")
contains an error whereby a quantity declared u32 can in fact go negative.

This problem was detected by Priit Laes who is switching b43 to use the
routine in the library functions of the kernel.

Fixes: 98650454 ("b43: make cordic common (LP-PHY and N-PHY need it)")
Reported-by: NPriit Laes <plaes@plaes.org>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Stable <stable@vger.kernel.org> # 2.6.34
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Current driver includes macro that is available from general cordic
library. Use that and drop unused duplicate and unneeded internal
definitions.
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Now that these macros are in header file, we can eventually
clean up the duplicate macros present in the drivers that
utilize the same cordic algorithm implementation.

Also add CORDIC_ prefix to nonprefixed macros.
Reviewed-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NPriit Laes <plaes@plaes.org>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2018-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

second batch of iwlwifi patches intended for v4.21

* New FW debugging infrastructure;
* Some more work on 802.11ax;
* Improve support for multiple RF modules with 22000 devices;
* Remove an unused FW parameter;
* Other debugging improvements;

Enable the VHT extended NSS BW feature in iwlwifi/mvm.
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>