Used to define pinmux configurations where the pinmux function have no
representation in the configuration registers but instead solely depends
on a group selection.
Signed-off-by: NNiklas Söderlund <niso@kth.se>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The SoC data structure allocated at init time only holds a regulator
pointer that is only used in the init function. Replace it with a local
variable and get rid of the SoC data structure allocation altogether.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In the multiplatform kernel case the IRQs associated with the PFC GPIOs
are specified through DT. The pinmux_irq irq field is thus ignored by
the code, and doesn't need to be set.

This will allow removing the mach/irq.h include from pfc-*.c files that
was required for the irq_pin() macro used to initialize the irq field.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The arrays are never modified, make them const.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The enum_ids and var_field_width fields of struct pinmux_data_reg and
pinmux_cfg_reg are initialized using compound literals. Cast them to
const to store them in .rodata.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

0 is a valid GPIO value, use -1 to terminate the gpios array in IRQ
lists.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The macro is defined identically in four different locations. Share it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Commit 7cbb0e55 ("sh-pfc: Don't duplicate argument to PINMUX_GPIO
macro") erronesouly modified the PINMUX_GPIO macro in a way that
resulted in all pins being named "name". Fix the macro to name the pins
correctly.

Cc: stable@vger.kernel.org
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pins with selectable functions but without a GPIO port can't be named
PORT_# or GP_#_#. Add a SH_PFC_PIN_NAMED macro to declare such pins in
the pinmux pins array, naming them with the PIN_ prefix followed by the
pin physical position.

In order to make sure not to register those pins as GPIOs, add a
SH_PFC_PIN_CFG_NO_GPIO pin flag to denote pins without a GPIO port.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

Remove the manually specified ranges from PFC SoC data and compute the
ranges automatically. This prevents ranges from being out-of-sync with
pins definitions.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

The pin number is usually equal to the GPIO number but can differ when
GPIO numbering is sparse.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

The PORT_1 macro invokes a macro passed as a parameter. Pass the pin
number down to that macro at the bottom of the call stack. This will be
used to compute the pin ranges automatically.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

Pass down the port number down to the PORT_1 macro. The port number will
be used to compute the pin ranges automatically.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

The PINMUX_GPIO macro takes a port name and a data mark, respectively of
the form GPIO_name and name_DATA. Modify the macro to take the name as a
single argument and derive the port name and data mark from it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

The SoC has a bank-style PFC. Replace the custom-defined macros with
common macros from sh-pfc.h.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Move the pin definition macros to a common header file.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

Move macros defined in several SoC data files to a common location and
document them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

The typedef only conceals the real variable type without bringing any
additional value (see Documentation/CodingStyle, section 5.b). Moreover,
it polutes the pinmux namespace. Replace it with the integer type it
used to hide.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

The macro isn't used, remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

Two integer field structures are needlesly defined as const. Remove the
const keyword.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

The SH_PFC_MARK_INVALID macro and the PINMUX_FLAG_TYPE, GPIO_CFG_REQ and
GPIO_CFG_FREE enum entries are used, remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

Most of the PORT_DATA_* macros are not used, remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

The ranges are not used anymore, remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>

Add two optional init and exit SoC operations and call them from the
core at probe and remove time.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Make GPIO support optional for platforms that don't support GPIOLIB.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The existing PFC pinconf implementation, tied to the PFC-specific pin
types, isn't used by drivers or boards. Replace it with the generic
pinconf types to implement bias (pull-up/down) setup. Other pin
configuration options can be implemented later if needed.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

None of the SoC data need to be modified. Constify it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

The purpose of the dry-run is to ensure that a pin about to be
configured isn't in use. However, the current implementation is a no-op.
This proves that the dry-run isn't essential. Remove it.

Freeing configuration then becomes a no-op as well. Remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

The sh_pfc_pin structure supplied in SoC data contains information about
pin configuration and name. It's abused to store GPIO data registers
information and pin config type. Move those fields out of the
pinmux_data_reg structure into the new sh_pfc_gpio_pin and
sh_pfc_pin_config structures.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

The pinmux_data_reg structure supplied in SoC data contains information
about data registers. It's abused to store per-device mapped iomem and
shadow values. Move those fields out of the pinmux_data_reg structure
into the per-device sh_pfc_chip structure.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All data registers are located in the same memory resource. Locate the
mapped resource at initializat time and use it directly instead of
computing a mapped address for each register. This gets rid of the
mapped_reg field of the pinmux_data_reg structure.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

The sh-pfc driver exposes one fake group and function per GPIO pin. As
the pinctrl and pinmux APIs are not used by any SuperH and SH Mobile
board or driver, drop the fake groups and functions and replace them by
a real pinctrl and pinmux implementation.

Groups and functions must now be explicitly provided by PFC SoC-specific
data.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

The PFC driver assumes that the value of the GPIO_PORTxxx enumeration
names are equal to the port number. This isn't true when the port number
space is sparse, as with the SH73A0.

Fix the issue by adding support for pin numbers ranges specified through
SoC data. When no range is specified the driver considers that the PFC
implements a single contiguous range for all pins.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

The macros are defined identically and used in two SoC-specific files,
share them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Instead of converting the GPIO number to an enum_id and looking up IRQ
table entries by enum_id, replace the pinmux_irq enum_ids field with a
gpios field and lookup entries using the GPIO number.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

And drop the pinmux_flag_t typedef.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Split the GPIOs table into a pins table for real GPIOs and a functions
table for function GPIOs.

Only register pins with the pinctrl core. The function GPIOs remain
accessible as GPIOs.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

This ensures that the field is not modified, which is a prerequisite for
the rest of the PFC refactoring work.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

All function GPIO entries are initialized with the GPIO_FN macro that
expands to the PINMUX_GPIO macro, used to initialize real GPIOs. Create
a PINMUX_GPIO_FN macro that duplicates PINMUX_GPIO and sets flags to
PINMUX_TYPE_FUNCTION and use it in GPIO_FN, and make PINMUX_GPIO set
flags to PINMUX_TYPE_GPIO.

This removes the need to initialize GPIO flags at runtime and thus
simplifies the code, preparing for the GPIO and functions split.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

The field is unused, remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>