This commit adds checking whether clock-frequency property acquisition
has succeeded. If not, the frequency is set to 100kHz by default.

The Device Tree binding documentation is updated accordingly.

Based on the intials patches from Zbigniew Bodek
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NZbigniew Bodek <zbb@semihalf.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allow udev to autoload the module when booting with device-tree
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The driver returns -ENODEV as error code if it did not get an ACK
from the device. Per Documentation/i2c/fault-codes, it should
return -ENXIO.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds the i801 SMBus Controller DeviceIDs for the Intel Coleto Creek PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

We've been lucky not to have any interrupts fire during the suspend
path, otherwise we would have unpredictable behaviour in the kernel.

Based on the logic of the kernel code interrupts from i2c should be
prohibited during suspend. Kernel writes 0 to the I2C_IE register in
the omap_i2c_runtime_suspend() function. In the other side kernel
writes saved interrupt flags to the I2C_IE register in
omap_i2c_runtime_resume() function. I.e. interrupts should be disabled
during suspend.

This works for chips with version1 registers scheme. Interrupts are
disabled during suspend. For chips with version2 scheme registers
writting 0 to the I2C_IE register does nothing (because now the
I2C_IRQENABLE_SET register is located at this address). This register
is used to enable interrupts. For disabling interrupts
I2C_IRQENABLE_CLR register should be used.

Because the registers I2C_IRQENABLE_SET and I2C_IE have the same
addresses, the interrupt enabling procedure is unchanged.

I've checked that interrupts in the i2c controller are still enabled
after writting 0 to the I2C_IRQENABLE_SET register. With this patch
interrupts are disabled in the omap_i2c_runtime_suspend() function.

Patch is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
tag: v3.10-rc2

Verified on OMAP4430.
Signed-off-by: NOleksandr Dmytryshyn <oleksandr.dmytryshyn@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

On OLPC XO-1.75 (MMP2), a WARN_ON() was occurring during boot
since the clock being enabled by i2c-pxa had not been prepared.

Use clk_prepare_enable() to ensure that the prepare operation
has taken place, and use clk_disable_unprepare() in the matching
shutdown paths.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This reverts commit c80f5284.
Regressions have been found and also run time based instantiation would
fail. We need more thoughts on this.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The Nomadik I2C was using a local atomic counter to number
the I2C adapters. This does not work on configurations where
you also add, say a GPIO bit-banged adapter to the system.
They will start to conflict about being adapter 0.

There is no reason to use the numbered adapter function, and
the semantic effect on systems with only Nomadik I2C blocks
will be none - instead of increasing the number atomically
in the driver itself, it is done in the I2C core.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The Nomadik I2C block was introduced with the Nomadik STn8815
SoC (the STn8810 incidentally is identical to the one named
i2c-stu300.c). However as developments have only been tested
on the DB8500 family, it was not properly working with the
STn8815 anymore.

Rectify this by adding some vendor variant data in the same
manner as other PrimeCells, and switch code path depending
on version.

Tested on the S8815 Nomadik dongle.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add the compatible string for the Allwinner A10 i2c controller and the
associated register layout.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The Allwinner i2c controller uses the same logic as the Marvell one, but
with slightly different register offsets.

Introduce a structure that will be passed by either the pdata or
associated to the compatible strings, and that holds the various
registers that might be needed.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

These macros make it more comprehensive to access to useful masked and
shifted area of the various registers used.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds support for the I2C bus controllers found on Wondermedia
8xxx-series SoCs. Only master-mode is supported.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
[wsa: fixed one macro to shift 8 instead of 16]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The designware block is not always properly disabled in the case of
transfer errors. Interrupts from aborted transfers might be handled
after the data structures for the following transfer are initialised but
before the hardware is set up. This can corrupt the data structures to
the point that the system is stuck in an infinite interrupt loop (where
FIFOs are never emptied because dev->msg_read_idx == dev->msgs_num).

This patch cleanly disables the designware-i2c hardware at the end of
every transfer, be it successful or not.
Signed-off-by: NChristian Ruppert <christian.ruppert@abilis.com>
[wsa: extended the comment]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

TWI transfer interrupts may be lost when system is heavily handling other
interrupts, while current transfer handler depends on each accurate interrupt
and misses some data in this case. Because there are 2 2-byte FIFOs in blackfin
TWI controller, the occurrence of the data loss can be reduced by reading till
the RX FIFO is empty and writing till the TX FIFO is full.
Reported-by: NBob Maris <mail@maris-ee.eu>
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This tries to address an issue found when writing an MFD driver
for the Nomadik STw481x PMICs: as the platform is using device
tree exclusively I want to specify the driver matching like
this:

static const struct of_device_id stw481x_match[] = {
	{ .compatible = "st,stw4810", },
	{ .compatible = "st,stw4811", },
	{},
};

static struct i2c_driver stw481x_driver = {
	.driver = {
		.name	= "stw481x",
		.of_match_table = stw481x_match,
	},
	.probe		= stw481x_probe,
	.remove		= stw481x_remove,
};

However that turns out not to be possible: the I2C probe code
is written so that the probe() call is always passed a match
from i2c_match_id() using non-devicetree matches.

This is probably why most devices using device tree for I2C
clients currently will pass no .of_match_table *at all* but
instead just use .id_table from struct i2c_driver to match
the device. As you realize that means that the whole idea with
compatible strings is discarded, and that is why we find strange
device tree I2C device compatible strings like "product" instead
of "vendor,product" as you could expect.

Let's figure out how to fix this before the mess spreads. This
patch will allow probeing devices with only an of_match_table
as per above, and will pass NULL as the second argument to the
probe() function. If the driver wants to deduce secondary info
from the struct of_device_id .data field, it has to call
of_match_device() on its own match table in the probe function
device tree probe path.

If drivers define both an .of_match_table *AND* a i2c_driver
.id_table, the .of_match_table will take precedence, just
as is done in the i2c_device_match() function in i2c-core.c.

I2C devices probed from device tree should subsequently be
fixed to handle the case where of_match_table() is
used (I think none of them do that today), and platforms should
fix their device trees to use compatible strings for I2C devices
instead of setting the name to Linux device driver names as is
done in multiple cases today.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

If a process receives signal while it is waiting for I2C transfer to
complete, an error is returned to the caller and the transfer is aborted.
This can cause the driver to fail subsequent transfers. Also according to
commit d295a86e (i2c: mv64xxx: work around signals causing I2C
transactions to be aborted) I2C drivers aren't supposed to abort
transactions on signals.

To prevent this switch to use wait_for_completion_timeout() instead of
wait_for_completion_interruptible_timeout() in the designware I2C driver.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NChristian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Since commit ab78029e (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.

So remove devm_pinctrl_get_select_default() from the driver.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Since commit ab78029e (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.

So remove devm_pinctrl_get_select_default() from the driver.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Asking for a multi-part message to be handled by this driver is racy; it
has been observed that the following sequence is possible with this
driver:

	- send start
	- send address + write
	- send data
	- send (repeated) start
	- send address + write
	- send (repeated) start
	- send address + read
	- unrecoverable bus hang (except by system reset)

The problem is that the interrupt handling sees the next event after the
first repeated start is sent - the IFLG bit is set in the register even
though INTEN is disabled.

Let's fix this by moving all of the message processing into interrupt
context, rather than having it partly in IRQ and partly in process
context.  This allows us to move immediately to the next message in the
interrupt handler and get on with the transfer, rather than incuring a
couple of scheduling switches to get the next message.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Move mv64xxx_i2c_prepare_for_io() higher up in the driver to avoid a
future forward declaration for this function.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

As this driver does not advertise protocol mangling support
(I2C_FUNC_PROTOCOL_MANGLING is not set), having code to act on
I2C_M_NOSTART is illogical, and in any case isn't supportable on
anything but the first message - which makes no sense.  Remove
the I2C_M_NOSTART code.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Propagate the error code from request_irq() rather than ignoring it
entirely.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

As we're changing to using devm_* APIs to fix various problems
in this driver, lets also do devm_kzalloc() while we're here too.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This driver forgets to use clk_put().  Rather than adding clk_put(),
lets instead use devm_clk_get() to obtain this clock so that it's
automatically handled on cleanup.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Eliminate reg_base_p and reg_size, mv64xxx_i2c_unmap_regs() and an
unchecked ioremap() return from this driver by using the devm_*
API for requesting and ioremapping resources.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

mv64xxx_i2c_map_regs() already returns an error code, so lets
propagate that to mv64xxx_i2c_probe()'s caller.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Moorestown support is removed from kernel and Medfield is supported by
i2c-designware-pci. But i2c-intel-mid is still in upstream and community
resources are wasted to maintain it.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Pull m68k fix from Geert Uytterhoeven:
 "A boot lock-up on Mac, also destined for stable"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/mac: Fix unexpected interrupt with CONFIG_EARLY_PRINTK

Pull s390 fixes from Martin Schwidefsky:
 "Recent bug fixes, one of them touches a common code file.

  It adds two #ifndef/#endif pairs to asm-generic/io.h to be able to
  override xlate_dev_kmem_ptr and xlate_dev_mem_ptr."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/pgtable: Fix gmap notifier address
  s390/dasd: fix handling of gone paths
  s390/pgtable: Fix check for pgste/storage key handling
  arch: s390: appldata: using strncpy() and strnlen() instead of sprintf()
  s390/smp: lost IPIs on cpu hotplug
  kernel: Fix s390 absolute memory access for /dev/mem
  s390/dma: do not call debug_dma after free

Pull cgroup fixes from Tejun Heo:

 - Fix for yet another xattr bug which may lead to NULL deref.

 - A subtle bug in for_each_descendant_pre().  This bug requires quite
   specific conditions to trigger and isn't too likely to actually
   happen in the wild, but maybe that just makes it that much more
   nastier.

 - A warning message added for silly cgroup re-mount (not -o remount,
   but unmount followed by mount) behavior.

* 'for-3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: warn about mismatching options of a new mount of an existing hierarchy
  cgroup: fix a subtle bug in descendant pre-order walk
  cgroup: initialize xattr before calling d_instantiate()

Pull libata changes from Tejun Heo:
 "Nothing too interesting.  PCI ID additions, some sata_rcar fixes and a
  fringe bug fix for DMADIR handling which shouldn't affect any device
  remotely modern."

* 'for-3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  sata_rcar: fix interrupt handling
  ahci: add an observed PCI ID for Marvell 88se9172 SATA controller
  sata_rcar: clear STOP bit in bmdma_start() method
  libata: make ata_exec_internal_sg honor DMADIR
  ata_piix: add PCI IDs for Intel BayTail
  libata: update "Maintained by:" tags

The driver's interrupt handling code is too picky in deciding whether it should
handle an interrupt or not which causes completely unneeded spurious interrupts.
Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read
to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't
get cleared by writing to the SATAINTSTAT register in the interrupt mode we use.

Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for
enabled interrupts and we should clear  only those interrupts  that we have read
as active first time around, because else we have  a  race and risk clearing  an
interrupt that  can  occur between read  and write of the  SATAINTSTAT  register
and never registering it...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

Pull parisc fixes from Helge Deller:
 "This patcheset includes fixes for:

   - the PCI/LBA which brings back the stifb graphics framebuffer
     console
   - possible memory overflows in parisc kernel init code
   - parport support on older GSC machines
   - avoids that users by mistake enable PARPORT_PC_SUPERIO on parisc
   - MAINTAINERS file list updates for parisc."

* 'for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: parport0: fix this legacy no-device port driver!
  parport_pc: disable PARPORT_PC_SUPERIO on parisc architecture
  parisc/PCI: lba: fix: convert to pci_create_root_bus() for correct root bus resources (v2)
  parisc/PCI: Set type for LBA bus_num resource
  MAINTAINERS: update parisc architecture file list
  parisc: kernel: using strlcpy() instead of strcpy()
  parisc: rename "CONFIG_PA7100" to "CONFIG_PA7000"
  parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50
  parisc: memory overflow, 'name' length is too short for using

Fix the above kernel error from parport_announce_port() on 32bit GSC
machines (e.g. B160L). The parport driver requires now a pointer to the
device struct.
Signed-off-by: NHelge Deller <deller@gmx.de>

If enabled, CONFIG_PARPORT_PC_SUPERIO scans on PC-like hardware for
various super-io chips by accessing i/o ports in a range which will
crash any parisc hardware at once.

In addition, parisc has it's own incompatible superio chip
(CONFIG_SUPERIO), so if we disable PARPORT_PC_SUPERIO completely for
parisc we can avoid that people by accident enable the parport_pc
superio option too.
Signed-off-by: NHelge Deller <deller@gmx.de>

commit dc7dce28
Author: Bjorn Helgaas <bhelgaas@google.com>
Date:   Fri Oct 28 16:27:27 2011 -0600
   parisc/PCI: lba: convert to pci_create_root_bus() for correct root bus
                    resources

  Supply root bus resources to pci_create_root_bus() so they're correct
  immediately.  This fixes the problem of "early" and "header" quirks seeing
  incorrect root bus resources.

added tests for elmmio_space.start while it should use
elmmio_space.flags.  This for example led to incorrect resource
assignments and a non-working stifb framebuffer on most parisc machines.

LBA 10:1: PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [io  0x12000-0x13fff] (bus address [0x2000-0x3fff])
pci_bus 0000:01: root bus resource [mem 0xfffffffffa000000-0xfffffffffbffffff] (bus address [0xfa000000-0xfbffffff])
pci_bus 0000:01: root bus resource [mem 0xfffffffff4800000-0xfffffffff4ffffff] (bus address [0xf4800000-0xf4ffffff])
pci_bus 0000:01: root bus resource [??? 0x00000001 flags 0x0]
Signed-off-by: NHelge Deller <deller@gmx.de>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>