When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: hersen wu <hersenxs.wu@amd.com>
Cc: "Leo (Hanghong) Ma" <hanghong.ma@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Found issue in EDID Emulation where if we connect a display using
 a passive HDMI-DP dongle, disconnect it and then try to emulate
 a display using DP, we could not see 4K modes.  This was because
 on a disconnect, dongle_max_pix_clk was still set so when we
 emulate using DP, in dc_link_validate_mode_timing(), it would
 think we were still using a dongle and limit the modes we support.

[How]
In dc_link_detect(), set dongle_max_pix_clk to 0 when we detect
 a hotplug out ( if new_connection_type = dc_connection_none ).
Signed-off-by: NSamson Tam <Samson.Tam@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

refactor a code so we will call clk_mgr's enable_pme_wa function so we
can use pme_wa for future asics. This way we don't need to worry about
different ASIC since clk_mgr already have that information
Signed-off-by: NSu Sung Chung <Su.Chung@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Description]

The spec does not allow POST_LT_ADJ_GRANTED to be set when TPS4 is used.
Signed-off-by: Nabdoulaye berthe <abdoulaye.berthe@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We incorrectly began powering down the display at boot/resume whenever
fast boot was not possible. This should not be done in the case where there
exists a stream for the eDP since this implies that we want to turn it on.

[How]
Add check for eDP stream to decide whether to power off edp.
Signed-off-by: NSivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NReza Amini <Reza.Amini@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
By the time output csc matrix is being programmed, stream connection to
OPP has been established, but this information has not been relayed back
to HUBP.
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Our existing logic in deciding whether to use RAM or ROM
depends on whether we are dealing with an identity gamma ramp.

[How]
In addition to the is_identity flag
a new is_logical_identity flag has been
added. The is_identity flag now denotes
whether the OS gamma is an RGB256 identity
and the new logical identity will inidicate
that the given gamma ramp regardless of its
type is identity.
Signed-off-by: NHarmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
For debugging underflow issues it can be useful to have asserts when the
underflow initially occurs.

[How]
Read the underflow status registers after actions that have a high risk
of causing underflow and assert that no underflow occurred. If underflow
occurred, clear the bit.
Signed-off-by: NThomas Lim <Thomas.Lim@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Currently vmid is decided internally inside dc. This makes it
difficult to use vmid use with external components.

This change moves vmid logic outside dc and allowing vmid to be
passed in as a parameter to DC.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
VBios sometimes reports incorrect object type as encoder instead of
connector

[How]
Change error message to debug message
Signed-off-by: NJordan Lazare <Jordan.Lazare@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

These are no longer needed, Also added RESERVED bits.
Signed-off-by: NChris Park <Chris.Park@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NHarry Wentland <Harry.Wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Using this logic breaks driver unload, this is a temporary fix
a followup patch will properly fix this
Signed-off-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
HPD not going to be high if Panel VDD is off
And all AUX transaction will fail :(

[How]
1. Power on VDD before attempting detection if it isn't already on
2. Improve the robustness by having a retry mechanism on the
first DPCD read after VDD on. If a particular board always holds
HPD high incorrectly, the AUX access may fail, so we can retry
in those scenarios. This change would only improve logic
since it prevents AUX failure leading to bad resolution on internal
panel.
3. We should never need to re-detect internal panel, so logic
is re-arranged a bit to skip earlier.
Signed-off-by: NAnthony Koo <Anthony.Koo@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
To prepare for the upcoming DRM plane color management properties
we need to correct a lot of wrong behavior and assumptions made for
CRTC color management.

The documentation added by this commit in amdgpu_dm_color explains
how the HW color pipeline works and its limitations with the DRM
interface.

The current implementation does the following wrong:
- Implicit sRGB DGM when no CRTC DGM is set
- Implicit sRGB RGM when no CRTC RGM is set
- No way to specify a non-linear DGM matrix that produces correct output
- No way to specify a correct RGM when a linear DGM is used

We had workarounds for passing kms_color tests but not all of the
behavior we had wrong was covered by these tests (especially when
it comes to non-linear DGM). Testing both DGM and RGM at the same time
isn't something kms_color tests well either.

[How]
The specifics for how color management works in AMDGPU and the new
behavior can be found by reading the documentation added to
amdgpu_dm_color.c from this patch.

All of the incorrect cases from the old implementation have been
addressed for the atomic interface, but there still a few TODOs for
the legacy one.

Note: this does cause regressions for kms_color@pipe-a-ctm-* over HDMI.

The result looks correct from visual inspection but the CRC no longer
matches. For reference, the test was previously doing the following:

linear degamma -> CTM -> sRGB regamma -> RGB to YUV (709) -> ...

Now the test is doing:

linear degamma -> CTM -> linear regamma -> RGB to YUV (709) -> ...
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NSun peng Li <Sunpeng.Li@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
This is meant to make it clearer that 0xf is not a valid OPP ID, and
that code making use of OPP IDs should not accept this value.
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NChris Park <Chris.Park@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

1. Add i2c_hw_Status check to make sure when HW i2c is in use.
2. Don't reset HW engine in is_hw_busy() and instead do this in
process_transaction() because SW i2c does not check if hw i2c is in use
Signed-off-by: NDerek Lai <Derek.Lai@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

No need to assert just return
Signed-off-by: NEric Bernstein <eric.bernstein@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Implement floor, ceil, and fabs
Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Almost every function in DC that works with stream state expects that
the current state on the stream is the one that it should be writing
out. These functions are typically triggered by specifying a particular
stream update - but the actual contents of the stream update itself
are ignored, leaving it to the DM to actually update the stream state
itself.

The problem with doing this in DM is a matter of timing. On Linux
most of this is incorrectly done in atomic check, when we actually want
it to be done during atomic commit tail while access to DC is locked.

To give an example, a commit requesting to modify color management
state for DM could come in, be rejected, but still have modified
the actual system state for the stream since it's shared memory. The
next time color management gets programmed it'll use the rejected
color management info - which might not even still be around if it's
a custom transfer function.

So a reasonable place to perform this is within DC itself and this is
the model that's currently in use for surface updates. DC can even
compare the current system state to the incoming surface update to
determine update level, something that can't currnetly be done with the
framework for stream updates.

[How]
Duplicate the framework used for surface updates for stream updates
as well. Copy all the updates after checking the update type.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Some panels return a link rate of 0 (unknown) in DPCD 0. In this case,
an appropriate mode cannot be set, and certain panels will show
corruption as they are forced to use a mode they do not support.

[HOW]
Read DPCD 10 in the case where supported link rate from DPCD 0 is
unknown, and pass that value on to the reported link rate.
This re-introduces behaviour present in previous versions that appears
to have been accidentally removed.
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NTao.Huang <Tao.Huang@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The module parameter to specify the default ABM level is now defined,
so hook it up in DM.

[How]
On connector reset specify the default level. DC will program this as
part of the modeset since it gets passed onto the stream in
dm_update_crtc_state.

It's only set for eDP connectors, but it doesn't matter if this is
specified for connectors or hardware that doesn't support ABM.

It's DC's responsibility to check that ABM can be set or adjusted, and
DC does check that the DMCU firmware is running and if there's backlight
control available.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NDavid Francis <david.francis@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Whenever the a modeset is allowed (but not neccessarily required) we
currently recreate all the planes in the state. Most IGT tests and
legacy IOCTLs create atomic commits with this flag set, so the pipes
are often unnecessarily reprogrammed.

Poor performance and stuttering can occur when many of these commits
are frequently issued.

This flag was needed when the appropriate conditions for checking
whether the planes needed a reset were not in place, but
should_reset_plane should cover everything needed now.

[How]
Drop the check for state->allow_modeset in should_reset_plane.

All planes on a CRTC should reset in the following conditions:
- The CRTC needs a modeset
- The CRTC degamma changes
- Planes are added or removed to the CRTC

These conditions are all covered in should_reset_plane.

We still can't drop the format change check in should_reset_plane since
fill_dc_plane_info_and_addr isn't called when validating the state, so
we can't tell if a FULL update is needed or not.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NDavid Francis <david.francis@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The old logic for checking which output depth to use relied on using
the current connector state rather than the new proposed state. This
was a problem when performing atomic commits since we weren't verifying
it against the incoming max_requested_bpc.

But switching this to only use the new state and not the current state
breaks filtering modes - it'll always assume that the maximum bpc
supported by the display is in use, which will cause certain modes
like 1440p@144Hz to be filtered even when using 8bpc.

[How]
Still use the connector->state if we aren't passed an explicit state.
This will respect the max_bpc the user currently has when filtering
modes.

Also remember to reset the default max_requested_bpc to 8 whenever
connector reset is called to retain old behavior when using the new
property.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110845Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Unlike our regular connectors, MST connectors don't start off with
an initial connector state. This causes a NULL pointer dereference to
occur when attaching the bpc property since it tries to modify the
connector state.

We need an initial connector state on the connector to avoid the crash.

[How]
Use our reset helper to allocate an initial state and reset the values
to their defaults. We were already doing this before, just not for
MST connectors.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
This will be useful for verifying whether we enter the correct output
color depth from IGT.

[How]
Locks the connector and associated CRTC if available and outputs
the current and maximum output bpc values.

Example:

cat /sys/kernel/debug/dri/0/DP-1/output_bpc
Current: 8
Maximum: 10

v2: Drop unneeded connector status check
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
DCN_VERSION_1_01 is no longer handled in the dal_hw_translate_init
switch since it was inadvertently dropped in the patch that removed the
unnecessary DCN1_01 guards.

This caused numerous regressions on DCN1_01 when loading the driver.

[How]
Add it back.

Fixes: 97df424f ("drm/amd/display: Drop DCN1_01 guards")
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When switching from vt to desktop with EDID emulation we can receive
an atomic commit such that we have a crtc where mode_changed = true.

During the dm_update_crtc_state disable pass we remove the stream from
the context and free it on the dm_new_crtc_state.

During the enable pass we compare the new provisional stream to the
dm_old_crtc_state->stream and determine that the stream is unchanged
and no scaling has been changed.

Following this, new_crtc_state->mode_changed is then set to false.
The connectors haven't changed and the CRTC active state hasn't changed
so drm_atomic_crtc_needs_modeset returns false, so we jump to
skip_modeset and we hit:

BUG_ON(dm_new_crtc_state->stream == NULL);

...since the old stream is gone from the context and the new stream is
also still NULL.

[How]
Ensure that we still a stream to reuse before checking if we can reuse
the old stream without a full modeset.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

These got added back by subsequent merges accidently.
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We can issue HDR static metadata as part of stream updates for
non-modesets as long as we force a modeset when entering or exiting HDR.

This avoids unnecessary blanking for simple metadata updates.

[How]
When changing scaling and abm for the stream also check if HDR has
changed and send the stream update. This will only happen in non-modeset
cases.

Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-3-nicholas.kazlauskas@amd.com

[Why]
For userspace to send static HDR metadata to the display we need to
attach the property on the connector and send it to DC.

[How]
The property is attached to HDMI and DP connectors. Since the metadata
isn't actually available when creating the connector this isn't a
property we can dynamically support based on the extension block
being available or not.

When the HDR metadata is changed a modeset will be forced for now.
We need to switch from 8bpc to 10bpc in most cases anyway, and we want
to fully exit HDR mode when userspace gives us a NULL metadata, so this
isn't completely unnecessary.

The requirement can later be reduced to just entering and exiting HDR
or switching max bpc.

Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-2-nicholas.kazlauskas@amd.com

add ticket for display bo, so that it can preempt busy bo.

v2: fix stupid rebase error
Signed-off-by: NChunming Zhou <david1.zhou@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Tested-by: NPierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Issue:
Will have follow error when reload driver:
[ 3986.567739] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:07.0/drm_dp_aux_dev'
[ 3986.567743] CPU: 6 PID: 1767 Comm: modprobe Tainted: G           OE     5.0.0-rc1-custom #1
[ 3986.567745] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 3986.567746] Call Trace:
......
[ 3986.567808]  drm_dp_aux_register_devnode+0xdc/0x140 [drm_kms_helper]
......
[ 3986.569081] kobject_add_internal failed for drm_dp_aux_dev with -EEXIST, don't try to register things with the same name in the same directory.

Reproduce sequences:
1.modprobe amdgpu
2.modprobe -r amdgpu
3.modprobe amdgpu

Root cause:
When unload driver, it doesn't unregister aux.

v2: Don't use has_aux
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We only want to manual trigger end-of-frame when the bottom-most
pipe is flipped to prevent overlays from ending the frame too early.

[How]
Check that the manual trigger is only firing on bottom plane.
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
There's some unnecessary mem allocation for CS_TFM_ID. What's worse, it
depends on LUT size and since it's 4K for CS_TFM_1D, it is 16x bigger
than in regular case when it's actually needed. This leads to some
crashes in stress conditions.

[How]
Skip ramp combining designed for RGB256 and DXGI gamma with CS_TFM_1D.
Signed-off-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
For commits with allow_modeset=false and CRTC degamma changes the planes
aren't reset. This results in incorrect rendering.

[How]
Reset the planes when color management has changed on the CRTC.
Technically this will include regamma changes as well, but it doesn't
really after legacy userspace since those commit with
allow_modeset=true.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>