Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Beacon transmission would get stuck if the NAV is
an invalid value for some reason. Check and correct
the NAV value in the HW when this happens.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All QCA chips have the ability to parse the CF Parameter Set
IE in beacons. If the IE is malformed in the beacons from some
APs [1], the HW locks up. In AP mode, a beacon stuck would happen
and in client mode, a disconnection usually is the result.

To fix this issue, set the AR_PCU_MISC_MODE2_CFP_IGNORE to ignore
the CFP IE in beacons - this is applicable for all chips. For
AP mode, if this issue happens, the NAV is also corrupted and has
to be reset - this will be done in a subsequent patch.

[1] : http://msujith.org/ath9k/cfp/Malformed-CF-Param.pngSigned-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX IQ calibration is disabled by default for AR9462, this
is done using the initvals (reg 0xa644).

But, to compensate for this, the AR_PHY_RX_DELAY register
should be set to the max allowed value when performing
calibration.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function returns a pointer. Hence return NULL instead of false.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAlbert Pool <albertpool@solcon.nl>
Reported-by: NMichael Landrum <landrummd@gmail.com>
Acked-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever the return value of snprintf() is used to calculate
remaining buffer-space, we wanted to use sncprintf() instead.

Indentation is adapted where possible. Some lines exceed the
line width limit, either they did it already before, or
since they can not be broken reasonably well.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Remove duplicate array mappings.
* Fix ETSI CCA compliance.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is missing for AR9565.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adjust the CCA values based on the regulatory domain
present in the EEPROM.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are 2 types of WB335 cards, 1-antenna and 2-antenna.
Identify them based on PCI subsystem IDs, this will be used
for MCI/BTCOEX tweaks.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These cards are based on WB335/AR9565.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Program the HW registers (AR_PHY_CCK_DETECT, AR_PHY_MC_GAIN_CTRL)
with the correct values for AR9565 to allow LNA combining.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a default antenna diversity value for AR9565 instead
of relying on the EEPROM/OTP programmed value.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script: (and a little typing)

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So that's it's possible to query chip id from ath10k anytime.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k doesn't support qca988x hw1.0 boards anymore. Unfortunately
the PCI id is the same in hw1.0 and hw2.0 so ath10k tries to use
hw1.0 boards anyway. But without hw1.0 workarounds in place
ath10k just crashes horribly.

To avoid using hw1.0 boards at all add a chip id detection
and fail the probe if hw1.0 is detected:

[ 5265.786408] ath10k: ERROR: qca988x hw1.0 is not supported
[ 5265.786497] ath10k: Unsupported chip id 0x043200ff
[ 5265.786574] ath10k: could not register driver core (-95)
[ 5265.793191] ath10k_pci: probe of 0000:02:00.0 failed with error -95

Also add a warning if there's an unknown chip id but continue
the boot process normally anyway.
Reported-by: NZaki Bakar <zaki.bm@gmail.com>
Tested-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_ce_init() and the functions it calls wakeup
the chip multiple times. Simplify that to call
ath10k_pci_wake() only once. This also makes it
easier to add error handling when wakeup fails.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

We should not try to access hw if wakeup fails so add
proper error checking for that. Also add the timeout lenght
to the warning message.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The error handling was just weird, simplify it.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is consistent with all other functions.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Void pointers are bad, mmkay.

No functional changes.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's easier to read t if the field names are visible.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's much more readable if struct entries in host_ce_config_wlan
are explicitly set.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

cacheline_sz is not used anywhere and can be removed.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The new naming makes more sense.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The new naming makes more sense.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The new naming makes more sense.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some parameters were unused and are not required.
They have no representation in firmware. Clean
them up.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was only written to and never read back. No use
to keep it around.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Simplifies memory managament of ce_state.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>