Only used in the gmc IP modules so just call the local
function directly.
Reviewed-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

These are not used outside of the respective gmc ip modules.
Reviewed-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We don't need to validate them again if the eviction counter didn't changed.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Keep track of the number of evictions since boot.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

irq need to update when gpu reset happens.
Signed-off-by: NChunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

With the current code, when we boot with the amdgpu
driver enabled and loaded, the VCE also automatically
remains enabled since bootup. This can be verified from
the output of amdgpu_pm_info. It does not matter whether
we boot into command line directly or into X, the VCE
stays enabled the entire time.

This patch addresses the issue and makes sure that
VCE is turned on only during playback, and remains
disaled otherwise.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NArindam Nath <arindam.nath@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

No need to stall the pipe when we are using firmware with the
fix.
Reviewed-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

v2: do not overwrite register when bitmap is zero
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NNicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

v2: do not overwrite register when bitmap is zero
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NNicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This parameter will allow disabling individual CUs on module load, e.g.
amdgpu.disable_cu=2.0.3,2.0.4 to disable CUs 3 and 4 of SE2.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NNicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

On workstation cards with ECC vram, the entirety of vram is cleared to 0
on asic init to set the ECC status correctly.  On non ECC boards, I don't
think they do any explicit clearing, but the vram controller is reset
which may cause issues with the data there.
Signed-off-by: NChunming Zhou <David1.Zhou@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NChunming Zhou <David1.Zhou@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This boosts Xonotic from 38fps to 47fps when artificially limiting VRAM to
256MB for testing. It should improve all CPU bound rendering situations
where we have a lot of swapping to/from VRAM.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When we pipeline evictions the page directory could already be
moving somewhere else when grab_id is called.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

It isn't used and not waiting for the GPU after scheduling a move is
actually quite dangerous.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Not needed any more.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Otherwise we could update the VM page tables while the move is only scheduled.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When we want to pipeline accelerated moves we need to wait in the fallback path.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Wait for idle before moving the BO in all drivers implementing
an accelerated move function.

This should keep the current behavior when removing the pre move wait.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

It changes the way to skip newline character and also avoids
warning message from some compiler.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NEric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch implements the debugfs to dump all currect firmware
version:

root@jenkins-All-Series:/home/jenkins# cat /sys/kernel/debug/dri/0/amdgpu_firmware_info
VCE feature version: 0, firmware version: 0x34040300
UVD feature version: 0, firmware version: 0x01451000
MC feature version: 0, firmware version: 0x00000000
ME feature version: 37, firmware version: 0x00000093
PFP feature version: 37, firmware version: 0x000000da
CE feature version: 37, firmware version: 0x00000080
RLC feature version: 1, firmware version: 0x0000010e
MEC feature version: 37, firmware version: 0x0000029e
MEC2 feature version: 37, firmware version: 0x0000029e
SMC feature version: 0, firmware version: 0x013353e6
SDMA0 feature version: 31, firmware version: 0x00000036
SDMA1 feature version: 0, firmware version: 0x00000036
Suggested-by: NAlex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The new amdgpu_firmware_info function will be used on amdgpu firmware
version debugfs.
Suggested-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

It was redundant with data_length, and in fact set incorrectly in one case
leading to an out-of-bound read by memcpy in acpi_ut_copy_esimple_to_isimple,
reported by CONFIG_KASAN=y.
Signed-off-by: NNicolai Hähnle <Nicolai.Haehnle@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Saves power when not in use.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NEric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Align to the jump table offset.  May fix hangs on some
asics with GFX PG enabled.
Reviewed-by: NNicolai Hähnle <nicolai.haehnle@amd.com>
Acked-by: NTom St Denis <tom.stdenis@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Align to the jump table offset. Fixes hangs on some
systems with GFX PG enabled.
Reviewed-by: NNicolai Hähnle <nicolai.haehnle@amd.com>
Tested-by: NNicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: NTom St Denis <tom.stdenis@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

 - adding amdgpu_cs_bo_status to track total size and
   total entry count of bo for each submission.
 - adding amdgpu_ttm_bo_move to track the bo eviction
   including the size of bo and the location before/after the move
Signed-off-by: NDavid Mao <David.Mao@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

 - adding memory type, prefered heap, allowed heap, and host visible
   information to the amdgpu_bo_create tracepoint.
 - adding bo size to the amdgpu_bo_list_set tracepoint.
Signed-off-by: NDavid Mao <David.Mao@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

To make the code more legible various numerical constants
have been changed to their #define'ed MASKs.
Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Initialize the variable in a straight-forward way instead of
hiding the initialization inside the loop. This can also
reduce one function call.
Signed-off-by: NAlex Xie <AlexBin.Xie@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use == instead of != in the if statement to make code easier understood
Signed-off-by: NAlex Xie <AlexBin.Xie@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add comment to describe some variables otherwise.
Signed-off-by: NAlex Xie <AlexBin.Xie@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Re-enable bus mastering after GPU reset. We disable it
at the top of these functions, so balance them by
re-enabling it.
Signed-off-by: NChunming Zhou <David1.Zhou@amd.com>
eviewed-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

So we know whether or not the reset succeeded.
Signed-off-by: NChunming Zhou <David1.Zhou@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

vm_flush() now comes directly after vm_grab_id().
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Just wait for any fence to become available, instead
of waiting for the last entry of the LRU.
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This fixes a fairness problem with the GPU scheduler. VM having lot of
jobs could previously starve VM with less jobs.
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Prefer to use a VMIDs which are idle on the ring we want to submit to. This
also removes bubbling idle VMIDs up on the LRU, which is actually not
beneficial.
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Check if the sync object is idle depending on the ring a submission works with.
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Stop hiding bugs, instead print a proper error when the scheduler
doesn't handle all dependencies.
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>