Some drivers unfortunately cannot support software crypto, but
mac80211 currently assumes that they do.

This has the issue that if the hardware enabling fails for some
reason, the software fallback is used, which won't work. This
clearly isn't desirable, the error should be reported and the
key setting refused.

Support this in mac80211 by allowing drivers to set a new HW
flag IEEE80211_HW_SW_CRYPTO_CONTROL, in which case mac80211 will
only allow software fallback if the set_key() method returns 1.
The driver will also need to advertise supported cipher suites
so that mac80211 doesn't advertise any (future) software ciphers
that the driver can't actually do.

While at it, to make it easier to support this, refactor the
ieee80211_init_cipher_suites() code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

These rates are treated the same as 160 MHz in the spec,
so it makes no sense to distinguish them. As no driver
uses them yet, this is also not a problem, just remove
them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In many cases, drivers can filter things like beacons that will
skew statistics reported by mac80211. To get correct statistics
in these cases, call drivers to obtain statistics and let them
override all values, filling values from mac80211 if the driver
didn't provide them. Not all of them make sense for the driver
to fill, so some are still always done by mac80211.

Note that this doesn't currently allow a driver to say "I know
this value is wrong, don't report it at all", or to sum it up
with a mac80211 value (as could be useful for "dropped misc"),
that can be added if it turns out to be needed.

This also gets rid of the get_rssi() method as is can now be
implemented using sta_statistics().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When hw acceleration is enabled, the GENERATE_IV or PUT_IV_SPACE flags
only require headroom space. Therefore, the tailroom-needed counter can
safely be decremented for most drivers.

The older incarnation of this patch (ca34e3b5) assumed that the above
holds true for all drivers. As reported by Christopher Chavez and
researched by Christian Lamparter and Larry Finger, this isn't a valid
assumption for p54 and cw1200.

Drivers that still require tailroom for ICV/MIC even when HW encryption
is enabled can use IEEE80211_KEY_FLAG_RESERVE_TAILROOM to indicate it.
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Cc: Christopher Chavez <chrischavez@gmx.us>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This reverts commit ca34e3b5.

It turns out that the p54 and cw2100 drivers assume that there's
tailroom even when they don't say they really need it. However,
there's currently no way for them to explicitly say they do need
it, so for now revert this.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=90331.

Cc: stable@vger.kernel.org
Fixes: ca34e3b5 ("mac80211: Fix accounting of the tailroom-needed counter")
Reported-by: NChristopher Chavez <chrischavez@gmx.us>
Bisected-by: NLarry Finger <Larry.Finger@lwfinger.net>
Debugged-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to let drivers have more dynamic U-APSD support,
move the enablement flag to the virtual interface driver
flags. This lets drivers not only set it up differently
for different interfaces, but also enable/disable on the
fly if needed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since multicast frames are marked as no-ack, using
IEEE80211_TX_STAT_ACK to check if they have been
successfully transmitted by the driver is incorrect
since a driver can choose to ignore transmission status
for no-ack frames. This results in incorrect accounting
for such frames.

To fix this issue, this patch introduces a new flag
that can be used by drivers to indicate error-free
transmission of no-ack frames.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
[add a note about not setting the flag for non-no-ack frames]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Move IEEE80211_TX_CTL_PS_RESPONSE to info->control.flags since
this is used only in the TX path (by ath9k). This frees up
a bit which can be used for other purposes.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This can be used by drivers that cannot reliably map tx status
information onto specific skbs.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This op works like .tx_status, except it does not need access to the
skb. This will be used by drivers that cannot match tx status
information to specific packets.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.

Move the event to its own function call internally and to
its own event attribute in nl80211.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows drivers with a firmware or chip-based rate lookup table to
use the most recent default rate selection without having to get it from
per-packet data or explicit ieee80211_get_tx_rate calls
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In TDLS (e.g., TDLS off-channel) there is a requirement for
some drivers to supply an unused TID between the AP and the
device to the FW, to allow sending PTI requests and to allow
the FW to aggregate on a specific TID for better throughput.

To ensure that the allocated TID is indeed unused, this patch
introduces an API for blocking the driver from TXing on that
TID.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When receiving a TDLS channel switch request or response, parse the frame
and call a new tdls_recv_channel_switch op in the low level driver with
the parsed data.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement the cfg80211 TDLS channel switch ops and introduce new mac80211
ones for low-level drivers.
Verify low-level driver support for the new ops when using the relevant
wiphy feature bit. Also verify the peer supports channel switching before
passing the command down.

Add a new STA flag to track the off-channel state with the TDLS peer and
make sure to cancel the channel-switch if the peer STA is unexpectedly
removed.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Radiotap vendor namespace data might still be useful, but we
reverted it because it used too much space in the RX status.
Put it back, but address the space problem by using a single
bit only and putting everything else into the skb->data.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).

Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.

Update the current users with the new prototype.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch adds 802.11p OCB (Outside the Context of a BSS) mode
support.

When communicating in OCB mode a mandatory wildcard BSSID
(48 '1' bits) is used.

The EDCA parameters handling function was changed to support
802.11p specific values.

The insertion of a newly discovered STAs is done in the similar way
as in the IBSS mode -- through the deferred insertion.

The OCB mode uses a periodic 'housekeeping task' for expiration of
disconnected STAs (in the similar manner as in the MESH mode).

New Kconfig option for verbose OCB debugging outputs is added.
Signed-off-by: NRostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The configured tx power is often limited by hardware capabilities,
channel settings, antenna configuration, etc.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
[fix tracing compilation]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will be helpful when using the mac80211_hwsim
wiphys and automated testing.  Let user create the
vifs as needed, and named as expected.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Support creating wiphy devices with an optional name.
This will be used by hwsim to have better automated control
over virtual radio creation/deletion.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow drivers to iterate all stations currently uploaded to them.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers need to know which station is the TDLS link initiator.
Expose this value via the mac80211 ieee80211_sta structure.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Export ieee80211_ie_split function, so it can be reused by
drivers which need to insert additional elements.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use the currently existing APIs between mac80211 and the low
level driver to implement WMM admission control.

The low level driver needs to report the media time used by
each transmitted packet in ieee80211_tx_status. Based on that
information, mac80211 will modify the QoS parameters of the
admission controlled Access Category when the limit is
reached. Once the original QoS parameters can be restored,
mac80211 will do so.

One issue with this approach is that management frames will
also erroneously be downgraded, but the upside is that the
implementation is simple. In the future, it can be extended
to driver- or device-based implementations that are better.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Channel switch with multiple channel contexts should now work fine.
Remove check that disallows switches when multiple contexts are in
use.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

As a counterpart to the pre_channel_switch operation, add a
post_channel_switch operation.  This allows the drivers to go back to
a normal configuration after the channel switch is completed.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers may need to prepare for a channel switch also when it is
initiated from the remote side (eg. station, P2P client).  To make
this possible, add a generic callback that can be called for all
interface types.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some devices may need the device timestamp in order to synchronize the
channel switch.  To pass this value back to the driver, add it to the
channel switch structure and copy the device_timestamp value received
in the rx info structure into it.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use the new static_smps / dynamic_smps feature bits
instead of mac80211-internal hw flags.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Extend mac80211 set_coverage_class API in order to enable ACK timeout
estimation algorithm (dynack) passing coverage class equals to -1
to lower drivers. Synchronize set_coverage_class routine signature with
mac80211 function pointer for p54, ath9k, ath9k_htc and ath5k drivers.
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Header-less cloned skbs with sufficient headroom need not be cloned
unless the tailroom is going to be modified.

Fix ieee80211_skb_resize so it would only resize cloned skbs if either
the header isn't released or the tailroom is going to be modified.

Some drivers might have assumed that skbs are never cloned, so add a HW
flag that explicitly permits cloned TX skbs. Drivers which do not modify
TX skbs should set this flag to avoid copying skbs.
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When hw acceleration is enabled, the GENERATE_IV or PUT_IV_SPACE flags
will only require headroom space. Consequently, the tailroom-needed
counter can safely be decremented.
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We currently track the QoS capability twice: for all peer stations
in the WLAN_STA_WME flag, and for any clients associated to an AP
interface separately for drivers in the sta->sta.wme field.

Remove the WLAN_STA_WME flag and track the capability only in the
driver-visible field, getting rid of the limitation that the field
is only valid in AP mode.
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers may be performing most of Tx/Rx
aggregation on their own (e.g. in firmware)
including AddBa/DelBa negotiations but may
otherwise require Rx reordering assistance.

The patch exports 2 new functions for establishing
Rx aggregation sessions in assumption device
driver has taken care of the necessary
negotiations.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
[fix endian bug]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Multi-vif in-place reservations happen when
it is impossible to allocate more channel contexts
as indicated by interface combinations.

Such reservations are not finalized until all
assigned interfaces are ready.

This still doesn't handle all possible cases
(i.e. degradation of number of channels) properly.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Split sched scan IEs to band specific and not band specific
blocks. Common IEs blocks may be sent to the FW once per command,
instead of per band.

This allows optimization of size of the command, which may be
required by some drivers (eg. iwlmvm with newer firmware version).

As this changes the mac80211 API, update all drivers to use the
new version correctly, even if they don't (yet) make use of the
split data.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.

As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>