The numd field of directive receive command takes number of dwords to
transfer. This fix has the correct calculation for numd.
Signed-off-by: NKwan (Hingkwan) Huen-SSI <kwan.huen@samsung.com>
Reviewed-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

We need to return an error if a timeout occurs on any NVMe command during
initialization. Without this, the nvme reset work will be stuck. A timeout
will have a negative error code, meaning we need to stop initializing
the controller. All postitive returns mean the controller is still usable.

bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196325Signed-off-by: NKeith Busch <keith.busch@intel.com>
Cc: Martin Peres <martin.peres@intel.com>
[jth consolidated cleanup path ]
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Currently we create the sysfs entry even if we fail mapping
it. In that case, the unmapping will not remove the sysfs created
file. There is no good reason to create a sysfs entry for a non
working CMB and show his characteristics.

Fixes: f63572df ("nvme: unmap CMB and remove sysfs file in reset path")
Signed-off-by: NMax Gurtovoy <maxg@mellanox.com>
Reviewed-by: NStephen Bates <sbates@raithlin.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Currently, calls to nvmet_fc_rcv_fcp_req() always copied the
FC-NVME cmd iu to a temporary buffer before returning, allowing
the driver to immediately repost the buffer to the hardware.

To address timing conditions on queue element structures vs async
command reception, the nvmet_fc transport occasionally may need to
hold on to the command iu buffer for a short period. In these cases,
the nvmet_fc_rcv_fcp_req() will return a special return code
(-EOVERFLOW). In these cases, the LLDD must delay until the new
defer_rcv lldd callback is called before recycling the buffer back
to the hw.

This patch adds support for the new nvmet_fc transport defer_rcv
callback and recognition of the new error code when passing commands
to the transport.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

At queue creation, the transport allocates a local job struct
(struct nvmet_fc_fcp_iod) for each possible element of the queue.
When a new CMD is received from the wire, a jobs struct is allocated
from the queue and then used for the duration of the command.
The job struct contains buffer space for the wire command iu. Thus,
upon allocation of the job struct, the cmd iu buffer is copied to
the job struct and the LLDD may immediately free/reuse the CMD IU
buffer passed in the call.

However, in some circumstances, due to the packetized nature of FC
and the api of the FC LLDD which may issue a hw command to send the
wire response, but the LLDD may not get the hw completion for the
command and upcall the nvmet_fc layer before a new command may be
asynchronously received on the wire. In other words, its possible
for the initiator to get the response from the wire, thus believe a
command slot free, and send a new command iu. The new command iu
may be received by the LLDD and passed to the transport before the
LLDD had serviced the hw completion and made the teardown calls for
the original job struct. As such, there is no available job struct
available for the new io. E.g. it appears like the host sent more
queue elements than the queue size. It didn't based on it's
understanding.

Rather than treat this as a hard connection failure queue the new
request until the job struct does free up. As the buffer isn't
copied as there's no job struct, a special return value must be
returned to the LLDD to signify to hold off on recycling the cmd
iu buffer.  And later, when a job struct is allocated and the
buffer copied, a new LLDD callback is introduced to notify the
LLDD and allow it to recycle it's command iu buffer.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Some broken controllers (such as earlier Linux targets) pad model or
serial fields with 0-bytes rather than spaces. The NVMe spec disallows
0 bytes in "ASCII" fields.  Thus strip trailing 0-bytes, too. Also make
sure that we get no underflow for pathological input.
Signed-off-by: NMartin Wilck <mwilck@suse.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

qmi_wwan_disconnect is called twice when disconnecting devices with
separate control and data interfaces.  The first invocation will set
the interface data to NULL for both interfaces to flag that the
disconnect has been handled.  But the matching NULL check was left
out when qmi_wwan_disconnect was added, resulting in this oops:

  usb 2-1.4: USB disconnect, device number 4
  qmi_wwan 2-1.4:1.6 wwp0s29u1u4i6: unregister 'qmi_wwan' usb-0000:00:1d.0-1.4, WWAN/QMI device
  BUG: unable to handle kernel NULL pointer dereference at 00000000000000e0
  IP: qmi_wwan_disconnect+0x25/0xc0 [qmi_wwan]
  PGD 0
  P4D 0
  Oops: 0000 [#1] SMP
  Modules linked in: <stripped irrelevant module list>
  CPU: 2 PID: 33 Comm: kworker/2:1 Tainted: G            E   4.12.3-nr44-normandy-r1500619820+ #1
  Hardware name: LENOVO 4291LR7/4291LR7, BIOS CBET4000 4.6-810-g50522254fb 07/21/2017
  Workqueue: usb_hub_wq hub_event [usbcore]
  task: ffff8c882b716040 task.stack: ffffb8e800d84000
  RIP: 0010:qmi_wwan_disconnect+0x25/0xc0 [qmi_wwan]
  RSP: 0018:ffffb8e800d87b38 EFLAGS: 00010246
  RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
  RDX: 0000000000000001 RSI: ffff8c8824f3f1d0 RDI: ffff8c8824ef6400
  RBP: ffff8c8824ef6400 R08: 0000000000000000 R09: 0000000000000000
  R10: ffffb8e800d87780 R11: 0000000000000011 R12: ffffffffc07ea0e8
  R13: ffff8c8824e2e000 R14: ffff8c8824e2e098 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff8c8835300000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00000000000000e0 CR3: 0000000229ca5000 CR4: 00000000000406e0
  Call Trace:
   ? usb_unbind_interface+0x71/0x270 [usbcore]
   ? device_release_driver_internal+0x154/0x210
   ? qmi_wwan_unbind+0x6d/0xc0 [qmi_wwan]
   ? usbnet_disconnect+0x6c/0xf0 [usbnet]
   ? qmi_wwan_disconnect+0x87/0xc0 [qmi_wwan]
   ? usb_unbind_interface+0x71/0x270 [usbcore]
   ? device_release_driver_internal+0x154/0x210
Reported-and-tested-by: NNathaniel Roach <nroach44@gmail.com>
Fixes: c6adf779 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e5dadc65 ("ppp: Fix false xmit recursion detect with two ppp
devices") dropped the xmit_recursion counter incrementation in
ppp_channel_push() and relied on ppp_xmit_process() for this task.
But __ppp_channel_push() can also send packets directly (using the
.start_xmit() channel callback), in which case the xmit_recursion
counter isn't incremented anymore. If such packets get routed back to
the parent ppp unit, ppp_xmit_process() won't notice the recursion and
will call ppp_channel_push() on the same channel, effectively creating
the deadlock situation that the xmit_recursion mechanism was supposed
to prevent.

This patch re-introduces the xmit_recursion counter incrementation in
ppp_channel_push(). Since the xmit_recursion variable is now part of
the parent ppp unit, incrementation is skipped if the channel doesn't
have any. This is fine because only packets routed through the parent
unit may enter the channel recursively.

Finally, we have to ensure that pch->ppp is not going to be modified
while executing ppp_channel_push(). Instead of taking this lock only
while calling ppp_xmit_process(), we now have to hold it for the full
ppp_channel_push() execution. This respects the ppp locks ordering
which requires locking ->upl before ->downl.

Fixes: e5dadc65 ("ppp: Fix false xmit recursion detect with two ppp devices")
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Manually adjust the port settings of user ports once PHY polling has
completed. This patch extends the adjust_link callback to configure the
per port PMCR register, applying the proper values polled from the PHY.
Without this patch flow control was not always getting setup properly.
Signed-off-by: NShashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: NMuciri Gatimu <muciri@openmesh.com>
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

if the NIC fails to validate the checksum on TCP/UDP, and validation of IP
checksum is successful, the driver subtracts the pseudo-header checksum
from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't
do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails.

V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set
Reported-by: NShuang Li <shuali@redhat.com>
Fixes: f8c6455b ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE")
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the warning message on the parisc and IA64 architectures to show the
correct function name of the caller by using %pS instead of %pF. The
message is printed with the value of _RET_IP_ which calls
__builtin_return_address(0) and as such returns the IP address caller
instead of pointer to a function descriptor of the caller.

The effect of this patch is visible on the parisc and ia64 architectures
only since those are the ones which use function descriptors while on
all others %pS and %pF will behave the same.

Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: NHelge Deller <deller@gmx.de>
Fixes: eecabf56 ("random: suppress spammy warnings about unseeded randomness")
Fixes: d06bfd19 ("random: warn when kernel uses unseeded randomness")
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We allocate 'p_info->mfw_mb_cur' and 'p_info->mfw_mb_shadow' but we check
'p_info->mfw_mb_addr' instead of 'p_info->mfw_mb_cur'.

'p_info->mfw_mb_addr' is never 0, because it is initiliazed a few lines
above in 'qed_load_mcp_offsets()'.

Update the test and check the result of the 2 'kzalloc()' instead.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The synchronization type that was used earlier to guard the loop that
deletes unused log buffers may lead to a situation that prevents any
thread from going through the loop.

The patch deletes previously used synchronization mechanism and moves
the loop under the spin_lock so the similar cases won't be feasible in
the future.

Found by by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAnton Volkov <avolkov@ispras.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On L3, the qeth_hdr struct needs to be filled with the next-hop
IP address.
The current code accesses rtable->rt_gateway without checking that
rtable is a valid address. The accidental access to a lowcore area
results in a random next-hop address in the qeth_hdr.
rtable (or more precisely, skb_dst(skb)) can be NULL in rare cases
(for instance together with AF_PACKET sockets).
This patch adds the missing NULL-ptr checks.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Fixes: 87e7597b qeth: Move away from using neighbour entries in qeth_l3_fill_header()
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When Ethernet frames span mulitple URBs, the netdev buffer memory
pointed to by the asix_rx_fixup_info structure remains allocated
during the time gap between the 2 executions of asix_rx_fixup_internal().

This means that if ax88772_unbind() is called within this time
gap to free the memory of the parent private data structure then
a memory leak of the part filled netdev buffer memory will occur.

Therefore, create a new function asix_rx_fixup_common_free() to
free the memory of the netdev buffer and add a call to
asix_rx_fixup_common_free() from inside ax88772_unbind().

Consequently when an unbind occurs part way through receiving
an Ethernet frame, the netdev buffer memory that is holding part
of the received Ethernet frame will now be freed.
Signed-off-by: NDean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a risk that the members of the structure asix_rx_fixup_info
become unsynchronised leading to the possibility of a malfunction.

For example, rx->split_head was not being set to false after an
error was detected so potentially could cause a malformed 32-bit
Data header word to be formed.

Therefore add function reset_asix_rx_fixup_info() to reset all the
members of asix_rx_fixup_info so that future processing will start
with known initial conditions.

Also, if (skb->len != offset) becomes true then call
reset_asix_rx_fixup_info() so that the processing of the next URB
starts with known initial conditions. Without the call, the check
does nothing which potentially could lead to a malfunction
when the next URB is processed.

In addition, for robustness, call reset_asix_rx_fixup_info() before
every error path's "return 0". This ensures that the next URB is
processed from known initial conditions.
Signed-off-by: NDean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In asix_rx_fixup_internal() there is a risk that rx->ax_skb gets
reused after passing the Ethernet frame into the network stack via
usbnet_skb_return().

The risks include:

a) asynchronously freeing rx->ax_skb after passing the netdev buffer
   to the NAPI layer which might corrupt the backlog queue.

b) erroneously reusing rx->ax_skb such as calling skb_put_data() multiple
   times which causes writing off the end of the netdev buffer.

Therefore add a defensive rx->ax_skb = NULL after usbnet_skb_return()
so that it is not possible to free rx->ax_skb or to apply
skb_put_data() too many times.
Signed-off-by: NDean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing sub channel code did not wait for all the sub-channels
to completely initialize. This could lead to race causing crash
in napi_netif_del() from bad list. The existing code would send
an init message, then wait only for the initial response that
the init message was received. It thought it was waiting for
sub channels but really the init response did the wakeup.

The new code keeps track of the number of open channels and
waits until that many are open.

Other issues here were:
  * host might return less sub-channels than was requested.
  * the new init status is not valid until after init was completed.

Fixes: b3e6b82a ("hv_netvsc: Wait for sub-channels to be processed during probe")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a problem where the system gets stuck in a loop
unable to wakeup via power button in s2idle.

The problem happens because:
 - press power button:
   - system emits 0xc0 (power press), event ignored
   - system emits 0xc1 (power release), event processed,
     emited as KEY_POWER
   - set wakeup_mode to true
   - system goes to s2idle
 - press power button
   - system emits 0xc0 (power press), wakeup_mode is true,
     system wakes
   - system emits 0xc1 (power release), event processed,
     emited as KEY_POWER
   - system goes to s2idle again

To avoid this situation, process the presses (which matches what
intel-hid does too).

Verified on an Dell XPS 9365
Signed-off-by: NMario Limonciello <mario.limonciello@dell.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NDarren Hart (VMware) <dvhart@infradead.org>

The hns_roce_v1_create_lp_qp() returns NULL on error, not error pointers.

Fixes: bfcc681b ("IB/hns: Fix the bug when free mr")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Even the driver doesn't do anything with the clk source for SGMII
ports it needs to be enabled by doing a devm_clk_get(), if there is
a clk source in DT.

Fixes: 0db01097 ('xgene: Don't fail probe, if there is no clk resource for SGMII interfaces')
Signed-off-by: NThomas Bogendoerfer <tbogendoerfer@suse.de>
Tested-by: NLaura Abbott <labbott@redhat.com>
Acked-by: NIyappan Subramanian <isubramanian@apm.com>
Tested-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The extended address vector is the highest bit in be32 variable,
but it was compared with the lowest. This patch fixes the endianness
of that check and removes already declared define.

Fixes: 17d2f88f ("IB/mlx5: Add ODP atomics support")
Reviewed-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Uverbs device should be cleaned up only when there is no
potential usage of.

As part of ib_uverbs_remove_one which might be triggered upon reset flow
the device reference count is decreased as expected and leave the final
cleanup to the FDs that were opened.

Current code increases reference count upon opening a new command FD and
decreases it upon closing the file. The event FD is opened internally
and rely on the command FD by taking on it a reference count.

In case that the command FD was closed and just later the event FD we
may ensure that the device resources as of srcu are still alive as they
are still in use.

Fixing the above by moving the reference count decreasing to the place
where the command FD is really freed instead of doing that when it was
just closed.

fixes: 036b1063 ("IB/uverbs: Enable device removal when there are active user space applications")
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

initialize to zero the response structure to prevent
the leakage of "resp.reserved" field.

drivers/infiniband/core/uverbs_cmd.c:1178 ib_uverbs_resize_cq() warn:
	check that 'resp.reserved' doesn't leak information

Fixes: 33b9b3ee ("IB: Add userspace support for resizing CQs")
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Currently while resolving IP address to MAC address single delayed work
is used for resolving multiple such resolve requests. This singled work
is essentially performs two tasks.
(a) any retry needed to resolve and
(b) it executes the callback function for all completed requests

While work is executing callbacks, any new work scheduled on for this
workqueue is lost because workqueue has completed looking at all pending
requests and now looking at callbacks, but work is still under
execution. Any further retry to look at pending requests in
process_req() after executing callbacks would lead to similar race
condition (may be reduce the probably further but doesn't eliminate it).
Retrying to enqueue work that from queue_req() context is not something
rest of the kernel modules have followed.

Therefore fix in this patch utilizes kernel facility to enqueue multiple
work items to a workqueue. This ensures that no such requests
gets lost in synchronization. Request list is still maintained so that
rdma_cancel_addr() can unlink the request and get the completion with
error sooner. Neighbour update event handling continues to be handled in
same way as before.
Additionally process_req() work entry cancels any pending work for a
request that gets completed while processing those requests.

Originally ib_addr was ST workqueue, but it became MT work queue with
patch of [1]. This patch again makes it similar to ST so that
neighbour update events handler work item doesn't race with
other work items.

In one such below trace, (though on 4.5 based kernel) it can be seen
that process_req() never executed the callback, which is likely for an
event that was schedule by queue_req() when previous callback was
getting executed by workqueue.

 [<ffffffff816b0dde>] schedule+0x3e/0x90
 [<ffffffff816b3c45>] schedule_timeout+0x1b5/0x210
 [<ffffffff81618c37>] ? ip_route_output_flow+0x27/0x70
 [<ffffffffa027f9c9>] ? addr_resolve+0x149/0x1b0 [ib_addr]
 [<ffffffff816b228f>] wait_for_completion+0x10f/0x170
 [<ffffffff810b6140>] ? try_to_wake_up+0x210/0x210
 [<ffffffffa027f220>] ? rdma_copy_addr+0xa0/0xa0 [ib_addr]
 [<ffffffffa0280120>] rdma_addr_find_l2_eth_by_grh+0x1d0/0x278 [ib_addr]
 [<ffffffff81321297>] ? sub_alloc+0x77/0x1c0
 [<ffffffffa02943b7>] ib_init_ah_from_wc+0x3a7/0x5a0 [ib_core]
 [<ffffffffa0457aba>] cm_req_handler+0xea/0x580 [ib_cm]
 [<ffffffff81015982>] ? __switch_to+0x212/0x5e0
 [<ffffffffa04582fd>] cm_work_handler+0x6d/0x150 [ib_cm]
 [<ffffffff810a14c1>] process_one_work+0x151/0x4b0
 [<ffffffff810a1940>] worker_thread+0x120/0x480
 [<ffffffff816b074b>] ? __schedule+0x30b/0x890
 [<ffffffff810a1820>] ? process_one_work+0x4b0/0x4b0
 [<ffffffff810a1820>] ? process_one_work+0x4b0/0x4b0
 [<ffffffff810a6b1e>] kthread+0xce/0xf0
 [<ffffffff810a6a50>] ? kthread_freezable_should_stop+0x70/0x70
 [<ffffffff816b53a2>] ret_from_fork+0x42/0x70
 [<ffffffff810a6a50>] ? kthread_freezable_should_stop+0x70/0x70
INFO: task kworker/u144:1:156520 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this
message.
kworker/u144:1  D ffff883ffe1d7600     0 156520      2 0x00000080
Workqueue: ib_addr process_req [ib_addr]
 ffff883f446fbbd8 0000000000000046 ffff881f95280000 ffff881ff24de200
 ffff883f66120000 ffff883f446f8008 ffff881f95280000 ffff883f6f9208c4
 ffff883f6f9208c8 00000000ffffffff ffff883f446fbbf8 ffffffff816b0dde

[1] http://lkml.iu.edu/hypermail/linux/kernel/1608.1/05834.htmlSigned-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Each multicast group (MID) stores a bitmap of ports to which a packet
should be forwarded to in case an MDB entry associated with the MID is
hit.

Since the initial introduction of IGMP snooping in commit 3a49b4fd
("mlxsw: Adding layer 2 multicast support") the driver didn't correctly
free these multicast groups upon ungraceful situations such as the
removal of the upper bridge device or module removal.

The correct way to fix this is to associate each MID with the bridge
ports member in it and then drop the reference in case the bridge port
is destroyed, but this will result in a lot more code and will be fixed
in net-next.

For now, upon module removal, traverse the MID list and release each
one.

Fixes: 3a49b4fd ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some operations in the bridge driver such as MDB deletion are preformed
in an atomic context and thus deferred to a process context by the
switchdev infrastructure.

Therefore, by the time the operation is performed by the underlying
device driver it's possible the bridge port context is already gone.
This is especially true for removal flows, but theoretically can also be
invoked during addition.

Remove the warnings in such situations and return normally.

Fixes: c57529e1 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Fixes: 3922285d ("net: bridge: Add support for offloading port attributes")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When resuming, set up registers that have been lost in the sleep state.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The commit 304419d8 ("mmc: core: Allocate per-request data using the
block layer core") refactored mechanism of queue handling caused
mmc_init_request() can be called just after mmc_cleanup_queue() caused null
pointer dereference.

Another commit bbdc74dc ("mmc: block: Prevent new req entering queue
after its cleanup") tried to fix the problem. However it actually miss one
corner case.

We could still reproduce the issue mentioned with these steps:
(1) insert a SD card and mount it
(2) hotplug it, so it will leave md->usage still be counted
(3) reboot the system which will sync data and umount the card

[Unable to handle kernel NULL pointer dereference at virtual address
00000000
[user pgtable: 4k pages, 48-bit VAs, pgd = ffff80007bab3000
[[0000000000000000] *pgd=000000007a828003, *pud=0000000078dce003,
*pmd=000000007aab6003, *pte=0000000000000000
[Internal error: Oops: 96000007 [#1] PREEMPT SMP
[Modules linked in:
[CPU: 3 PID: 3507 Comm: umount Tainted: G        W
4.13.0-rc1-next-20170720-00012-g9d9bf45 #33
[Hardware name: Firefly-RK3399 Board (DT)
[task: ffff80007a1de200 task.stack: ffff80007a01c000
[PC is at mmc_init_request+0x14/0xc4
[LR is at alloc_request_size+0x4c/0x74
[pc : [<ffff0000087d7150>] lr : [<ffff000008378fe0>] pstate: 600001c5
[sp : ffff80007a01f8f0

....

[[<ffff0000087d7150>] mmc_init_request+0x14/0xc4
[[<ffff000008378fe0>] alloc_request_size+0x4c/0x74
[[<ffff00000817ac28>] mempool_create_node+0xb8/0x17c
[[<ffff00000837aadc>] blk_init_rl+0x9c/0x120
[[<ffff000008396580>] blkg_alloc+0x110/0x234
[[<ffff000008396ac8>] blkg_create+0x424/0x468
[[<ffff00000839877c>] blkg_lookup_create+0xd8/0x14c
[[<ffff0000083796bc>] generic_make_request_checks+0x368/0x3b0
[[<ffff00000837b050>] generic_make_request+0x1c/0x240

So mmc_blk_put wouldn't calling blk_cleanup_queue which actually the
QUEUE_FLAG_DYING and QUEUE_FLAG_BYPASS should stay. Block core expect
blk_queue_bypass_{start, end} internally to bypass/drain the queue before
actually dying the queue, so it didn't expose API to set the queue bypass.
I think we should set QUEUE_FLAG_BYPASS whenever queue is removed, although
the md->usage is still counted, as no dispatch queue could be found then.

Fixes: 304419d8 ("mmc: core: Allocate per-request data using the block layer core")
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When the device is non removable, the card detect signal is often used
for another purpose i.e. muxed to another SoC peripheral or used as a
GPIO. It could lead to wrong behaviors depending the default value of
this signal if not muxed to the SDHCI controller.

Fixes: bb5f8ea4 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Signed-off-by: NLudovic Desroches <ludovic.desroches@microchip.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

A check is performed on the ipad/opad in the safexcel_hmac_sha1_setkey
function, but the index used by the loop doing it is wrong. It is
currently the size of the state array while it should be the size of a
sha1 state. This patch fixes it.

Fixes: 1b44c5a6 ("crypto: inside-secure - add SafeXcel EIP197 crypto engine driver")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The safexcel_hmac_sha1_setkey function checks if an invalidation command
should be issued, i.e. when the context ipad/opad change. This checks is
done after filling the ipad/opad which and it can't be true. The patch
fixes this by moving the check before the ipad/opad memcpy operations.

Fixes: 1b44c5a6 ("crypto: inside-secure - add SafeXcel EIP197 crypto engine driver")
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This fixes a potential buffer overflow in isdn_net.c caused by an
unbounded strcpy.

[ ISDN seems to be effectively unmaintained, and the I4L driver in
  particular is long deprecated, but in case somebody uses this..
    - Linus ]
Signed-off-by: NJiten Thakkar <jitenmt@gmail.com>
Signed-off-by: NAnnie Cherkaev <annie.cherk@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently a bug in the sci_clk_get implementation causes it to always
return a clock belonging to the last device in the static list of clock
data. This is due to a bug in the init code that causes the array
used by sci_clk_get to only be populated with the clocks for the last
device, as each device overwrites the entire array with its own clocks.

Fix this by calculating the actual number of clocks for the SoC, and
allocating the whole array in one go. Also, we don't need the handle
to the init data array anymore after doing this, instead we can
just compare the dev_id / clk_id against the registered clocks and
use binary search for speed.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Reported-by: NDave Gerlach <d-gerlach@ti.com>
Fixes: b745c079 ("clk: keystone: Add sci-clk driver support")
Cc: Nishanth Menon <nm@ti.com>
Tested-by: NFranklin Cooper <fcooper@ti.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Otherwise bo->shadow_list (which is aliased by bo->mn_list) will not
appear empty in amdgpu_ttm_bo_destroy and cause an oops when freeing
former userptr BOs.
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

As I was staring at the si_init_golden_registers code, I noticed that
the Pitcairn initialization silently falls through the Cape Verde
initialization, and the Oland initialization falls through the Hainan
initialization. However there is no comment stating that this is
intentional, and the radeon driver doesn't have any such fallthrough,
so I suspect this is not supposed to happen.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Fixes: 62a37553 ("drm/amdgpu: add si implementation v10")
Cc: Ken Wang <Qingqing.Wang@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Marek Olšák" <maraeo@gmail.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: NMarek Olšák <marek.olsak@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

SCRQ resources are freed during renegotiation, but they are not
re-allocated afterwards due to some changes in the initialization
process. Fix that by re-allocating the memory after renegotation.

SCRQ's can also be freed if a server capabilities request fails.
If this were encountered during a device reset for example,
SCRQ's may not be re-allocated. This operation is not necessary
anymore so remove it.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHector Martin <marcan@marcan.st>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:

    QUERY_DEV_CAP_DIAG_RPRT_PER_PORT

However, it failed to introduce a corresponding entry in function
dump_dev_cap_flags2() for outputting a line in the message log
when this capability bit is set.

The change here fixes that omission.

Fixes: c7c122ed ("net/mlx4: Add diagnostic counters capability bit")
Reported-by: NMukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:

    MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP

However the value of MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP needs to stay
consistent with the value used in another namespace in
function dump_dev_cap_flags2(), which is manually kept in sync.
The change here restores that consistency.

Fixes: 7c3d21c8 ("net/mlx4_core: Preparation for VF vlan protocol 802.1ad")
Reported-by: NMukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>