Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 19 1月, 2017 1 次提交
    • T
      net: Remove usage of net_device last_rx member · 4a7c9726
      由 Tobias Klauser 提交于 
      The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f242738 ("bonding: use last_arp_rx in slave_last_rx()").

However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.

Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080d ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.

Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.

Compile-tested with allyesconfig and allmodconfig on x86 and arm.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NEric Dumazet <edumazet@google.com>
Reviewed-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4a7c9726
  3. 30 10月, 2016 3 次提交
  5. 27 10月, 2016 1 次提交
    • S
      batman-adv: Revert "use core MTU range checking in misc drivers" · 701470ba
      由 Sven Eckelmann 提交于 
      The maximum MTU is defined via the slave devices of an batman-adv
interface. Thus it is not possible to calculate the max_mtu during the
creation of the batman-adv device when no slave devices are attached. Doing
so would for example break non-fragmentation setups which then
(incorrectly) allow an MTU of 1500 even when underlying device cannot
transport 1500 bytes + batman-adv headers.

Checking the dynamically calculated max_mtu via the minimum of the slave
devices MTU during .ndo_change_mtu is also used by the bridge interface.

Cc: Jarod Wilson <jarod@redhat.com>
Fixes: b3e3893e ("net: use core MTU range checking in misc drivers")
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      701470ba
  7. 21 10月, 2016 1 次提交
    • J
      net: use core MTU range checking in misc drivers · b3e3893e
      由 Jarod Wilson 提交于 
      firewire-net:
- set min/max_mtu
- remove fwnet_change_mtu

nes:
- set max_mtu
- clean up nes_netdev_change_mtu

xpnet:
- set min/max_mtu
- remove xpnet_dev_change_mtu

hippi:
- set min/max_mtu
- remove hippi_change_mtu

batman-adv:
- set max_mtu
- remove batadv_interface_change_mtu
- initialization is a little async, not 100% certain that max_mtu is set
  in the optimal place, don't have hardware to test with

rionet:
- set min/max_mtu
- remove rionet_change_mtu

slip:
- set min/max_mtu
- streamline sl_change_mtu

um/net_kern:
- remove pointless ndo_change_mtu

hsi/clients/ssi_protocol:
- use core MTU range checking
- remove now redundant ssip_pn_set_mtu

ipoib:
- set a default max MTU value
- Note: ipoib's actual max MTU can vary, depending on if the device is in
  connected mode or not, so we'll just set the max_mtu value to the max
  possible, and let the ndo_change_mtu function continue to validate any new
  MTU change requests with checks for CM or not. Note that ipoib has no
  min_mtu set, and thus, the network core's mtu > 0 check is the only lower
  bounds here.

mptlan:
- use net core MTU range checking
- remove now redundant mpt_lan_change_mtu

fddi:
- min_mtu = 21, max_mtu = 4470
- remove now redundant fddi_change_mtu (including export)

fjes:
- min_mtu = 8192, max_mtu = 65536
- The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to
  get past the core net MTU range checks so fjes_change_mtu can validate a
  new MTU against what it supports (see fjes_support_mtu in fjes_hw.c)

hsr:
- min_mtu = 0 (calls ether_setup, max_mtu is 1500)

f_phonet:
- min_mtu = 6, max_mtu = 65541

u_ether:
- min_mtu = 14, max_mtu = 15412

phonet/pep-gprs:
- min_mtu = 576, max_mtu = 65530
- remove redundant gprs_set_mtu

CC: netdev@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
CC: Faisal Latif <faisal.latif@intel.com>
CC: linux-rdma@vger.kernel.org
CC: Cliff Whickman <cpw@sgi.com>
CC: Robin Holt <robinmholt@gmail.com>
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sathya Prakash <sathya.prakash@broadcom.com>
CC: Chaitra P B <chaitra.basappa@broadcom.com>
CC: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
CC: MPT-FusionLinux.pdl@broadcom.com
CC: Sebastian Reichel <sre@kernel.org>
CC: Felipe Balbi <balbi@kernel.org>
CC: Arvid Brodin <arvid.brodin@alten.se>
CC: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b3e3893e
  9. 17 10月, 2016 1 次提交
  11. 09 8月, 2016 3 次提交
  13. 04 7月, 2016 1 次提交
  15. 30 6月, 2016 3 次提交
  17. 29 6月, 2016 1 次提交
  19. 10 5月, 2016 6 次提交
  21. 05 5月, 2016 1 次提交
  23. 04 5月, 2016 2 次提交
  25. 24 4月, 2016 1 次提交
  27. 23 2月, 2016 2 次提交
  29. 10 2月, 2016 1 次提交
  31. 02 2月, 2016 4 次提交
  33. 28 8月, 2015 1 次提交
  35. 25 8月, 2015 1 次提交
  37. 19 8月, 2015 1 次提交
  39. 15 8月, 2015 1 次提交
  41. 05 8月, 2015 1 次提交
  43. 07 6月, 2015 2 次提交
    • A
      batman-adv: change the MAC of each VLAN upon ndo_set_mac_address · 94d1dd87
      由 Antonio Quartulli 提交于 
      The MAC address of the soft-interface is used to initialise
the "non-purge" TT entry of each existing VLAN. Therefore
when the user invokes ndo_set_mac_address() all the
"non-purge" TT entries have to be updated, not only the one
belonging to the non-tagged network.
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
      94d1dd87
    • S
      batman-adv: Add required includes to all files · 1e2c2a4f
      由 Sven Eckelmann 提交于 
      The header files could not be build indepdent from each other. This is
happened because headers didn't include the files for things they've used.
This was problematic because the success of a build depended on the
knowledge about the right order of local includes.

Also source files were not including everything they've used explicitly.
Instead they required that transitive includes are always stable. This is
problematic because some transitive includes are not obvious, depend on
config settings and may not be stable in the future.

The order for include blocks are:

 * primary headers (main.h and the *.h file of a *.c file)
 * global linux headers
 * required local headers
 * extra forward declarations for pointers in function/struct declarations

The only exceptions are linux/bitops.h and linux/if_ether.h in packet.h.
This header file is shared with userspace applications like batctl and must
therefore build together with userspace applications. The header
linux/bitops.h is not part of the uapi headers and linux/if_ether.h
conflicts with the musl implementation of netinet/if_ether.h. The
maintainers rejected the use of __KERNEL__ preprocessor checks and thus
these two headers are only in main.h. All files using packet.h first have
to include main.h to work correctly.
Reported-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
      1e2c2a4f
  45. 29 5月, 2015 1 次提交