The return value of snprintf may be greater than the size of
HNS3_DBG_READ_LEN, use scnprintf instead in hns3_dbg_cmd_read.
Signed-off-by: NChen Zhou <chenzhou10@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PUDE event is handled and the link is up, update the port SPAN
buffer size according to the current speed.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For SPAN egress mirroring buffer size, it is needed to use a different
formula for Spectrum and Spectrum-2. Move the buffer size computation to
ops and implement new formula for Spectrum-2.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid duplication of code that is doing buffsize update and put it into
a separate helper function.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently PTP code queries directly PTYS register for port speed from
work scheduled upon PUDE event. Since the speed needs to be used for
SPAN buffer size computation as well, push the code into a separate
helper.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace rtl8169_ioctl with new generic function phy_do_ioctl.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A number of network drivers has the same glue code to use phy_mii_ioctl
as ndo_do_ioctl handler. So let's add such a generic ndo_do_ioctl
handler to phylib.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SERDES statistics are valid for all members of the 6390 family,
not just the 6390 itself. Add the needed callbacks to all members of
the family.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

USXGMII supports passing link information in-band between PHY and MAC PCS,
add it to the list of protocols that support in-band AN mode.

Being a MAC-PHY protocol that can auto-negotiate link speeds up to 10
Gbps, we populate the initial supported mask with the entire spectrum of
link modes up to 10G that PHYLINK supports, and we let the driver reduce
that mask in its .phylink_validate method.
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The APIs can be used by Ethernet drivers without actually loading a PHY
driver. This may become more widespread in the future with 802.3z
compatible MAC PCS devices being locally driven by the MAC driver when
configuring for a PHY mode with in-band negotiation.

Check that drv is not NULL before reading from it.
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some reason, PHYLINK does not put the copper modes for 802.3bz
(NBASE-T) and 802.3an-2006 (10GBASE-T) in the PHY's supported mask, when
the PHY-MAC connection is a 10G-capable one (10GBase-KR, 10GBase-R,
USXGMII). One possible way through which the cable side can work at the
lower speed is by having the PHY emit PAUSE frames towards the MAC. So
fix that omission.

Also include the 2500Base-X fiber mode in this list while we're at it.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

snps databook noted that physical coding sublayer (PCS) interface
that can be used when the MAC is configured for the TBI, RTBI, or
SGMII PHY interface. we have RGMII and SGMII in a SoC and it also
has the PCS block. it needs stmmac_init_phy and stmmac_mdio_register
function for initializing phy when it used RGMII interface.
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a trap for NVE packets that the device decided to drop because their
overlay source MAC is multicast.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the trap IDs and trap group used to report tunnel drops. Register
tunnel packet traps and associated tunnel trap group with devlink
during driver initialization.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move L3_DROPS case to appear after L2_DROPS case.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize ECN mapping registers during router init according to
INET_ECN_encapsulate() and INET_ECN_decapsulate().

For IP-in-IP encapsulation, this is required to ensure that ECN bits in
the underlay are set in accordance with the kernel. For decapsulation,
this is required to ensure that packets with invalid ECN combination in
underlay and overlay are trapped to the kernel and not forwarded.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This register configures the actions that are done during IPinIP
decapsulation based on the ECN bits.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This register performs mapping from overlay ECN to underlay ECN during
IPinIP encapsulation.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a trap for packets that the device decided to drop because they are
not supposed to be routed. For example, IGMP queries can be flooded by
the device in layer 2 and reach the router. Such packets should not be
routed and instead dropped.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IRIF_DISABLED and ERIF_DISABLED are driver specific traps. Packets are
dropped for these reasons when they need to be routed through/from
existing router interfaces (RIF) which are disabled.

Add devlink driver-specific traps and mlxsw trap IDs used to report
these traps.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A queue can't belong to multiple traffic classes. So, reject
any such configuration that results in overlapped queues for a
traffic class.

Fixes: b1396c2b ("cxgb4: parse and configure TC-MQPRIO offload")
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

T6 can support 2 egress traffic management channels per port to
double the total number of traffic classes that can be configured.
In this configuration, if the class belongs to the other channel,
then all the queues must be bound again explicitly to the new class,
for the rate limit parameters on the other channel to take effect.

So, always explicitly bind all queues to the port rate limit traffic
class, regardless of the traffic management channel that it belongs
to. Also, only bind queues to port rate limit traffic class, if all
the queues don't already belong to an existing different traffic
class.

Fixes: 4ec4762d ("cxgb4: add TC-MATCHALL classifier egress offload")
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

found a warning by the following command:
./scripts/checkpatch.pl -f drivers/net/phy/adin.c

WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.rst
 #628: FILE: drivers/net/phy/adin.c:628:
+	msleep(10);
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the serdes link is set to 2500 using interfce type 2500base-X, lower
link speeds over on the line side should still be supported.
Rate adaptation is done out of band, in our case using AQR PHYs this is
done using flow control.
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow control is used with 2500Base-X and AQR PHYs to do rate adaptation
between line side 100/1000 links and MAC running at 2.5G.

This is independent of the flow control configuration settled on line
side though AN.

In general, allowing the MAC to handle flow control even if not
negotiated with the link partner should not be a problem, so the patch
just enables it in all cases.
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSN read can fail, for example on a kdump kernel without PCIe extended
config space support.  If DSN read fails, don't set the
BNXT_FLAG_DSN_VALID flag and continue loading.  Check the flag
to see if the stored DSN is valid before using it.  Only VF reps
creation should fail without valid DSN.

Fixes: 03213a99 ("bnxt: move bp->switch_id initialization to PF probe")
Reported-by: NMarc Smith <msmith626@gmail.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NTUPLE related firmware commands are sent to the wrong firmware
channel, causing all these commands to fail on new firmware that
supports the new firmware channel.  Fix it by excluding the 3
NTUPLE firmware commands from the list for the new firmware channel.

Fixes: 760b6d33 ("bnxt_en: Add support for 2nd firmware message channel.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost.  Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.

Fixes: ef347c0c ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: NEsben Haabendal <esben@geanix.com>
Acked-by: NHan Xu <han.xu@nxp.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

On system resume, the gpmi clock must be enabled before accessing gpmi
block.  Without this, resume causes something like

[  661.348790] gpmi_reset_block(5cbb0f7e): module reset timeout
[  661.348889] gpmi-nand 1806000.gpmi-nand: Error setting GPMI : -110
[  661.348928] PM: dpm_run_callback(): platform_pm_resume+0x0/0x44 returns -110
[  661.348961] PM: Device 1806000.gpmi-nand failed to resume: error -110

Fixes: ef347c0c ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: NEsben Haabendal <esben@geanix.com>
Acked-by: NHan Xu <han.xu@nxp.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

The commit 7b678c69 ("mtd: spi-nor: Merge spansion Quad Enable
methods") forgot to actually set the QE bit in some cases. Thus this
breaks quad mode accesses to flashes which support readback of the
status register-2. Fix it.

Fixes: 7b678c69 ("mtd: spi-nor: Merge spansion Quad Enable methods")
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

mtd->size is still unassigned when running spansion_post_sfdp_fixups()
hook, therefore use nor->params.size to determine the size of flash device.

This makes sure that 4-byte addressing opcodes are used on Spansion
flashes that are larger than 16MiB and don't have SFDP 4BAIT table
populated.

Fixes: 92094ebc ("mtd: spi-nor: Add spansion_post_sfdp_fixups()")
Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

The variable xmit_done is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The scope of function .ndo_tx_timeout was changed to include the hang
queue when a TX timeout event occurs. See commit 0290bd29
("netdev: pass the stuck queue to the timeout handler") for more
details. Now, drivers don't need to identify which queue is stopped.
Drivers can simply use the queue index provided by dev_watchdog and
execute all actions needed to restore network traffic. This commit do
some cleanups into Intel ice driver to remove a redundant loop to find
stopped queue.
Signed-off-by: NJulio Faracco <jcfaracco@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The scope of function .ndo_tx_timeout was changed to include the hang
queue when a TX timeout event occurs. See commit 0290bd29
("netdev: pass the stuck queue to the timeout handler") for more
details. Now, drivers don't need to identify which queue is stopped.
Drivers can simply use the queue index provided by dev_watchdog and
execute all actions needed to restore network traffic. This commit do
some cleanups into Intel i40e driver to remove a redundant loop to find
stopped queue.
Signed-off-by: NJulio Faracco <jcfaracco@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make use of the new txqueue parameter to the .ndo_tx_timeout function.
In fm10k_tx_timeout, remove the now unnecessary loop to determine which
Tx queue is stuck. Instead, just double check the specified queue

This could be improved further to attempt resetting only the specific
queue that got stuck. However, that is a much larger refactor and has
been left as a future improvement.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

PHY power management control should provide a reliable and accurate
indication of PHY reset completion and decrease the delay time
after a PHY reset
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

TCP segmentation offload allows a device to segment a single frame
into multiple frames with a data payload size specified in socket buffer.
As a result we can now send data approximately up to seven percents fast
than was previously possible on my system.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for blank NVM SKU
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the unused IGC_FUNC_0 definition and make the code cleaner
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>