This will be used by LLDD hardreset implementation.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Move ata_set_mode() failure handling outside of ap->ops->set_mode if
clause such that it can handle ap->ops->set_mode failures after it's
updated.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Devices which consumed all their changes used to be disabled every
iteration.  This causes unnecessary noise in the console output.
Disable once and leave alone.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Replace hard-coded waiting loops in sata_sil24 to ata_wait_register().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Replace ahci_poll_register() with ata_wait_register().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As waiting for some register bits to change seems to be a common
operation shared by some controllers, implement helper function
ata_wait_register().  This function also takes care of register write
flushing.

Note that the condition is inverted, the wait is over when the masked
value does NOT match @val.  As we're waiting for bits to change, this
test is more powerful and allows the function to be used in more
places.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Improve softreset error message.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

sil24_softreset calculated timeout by adding ATA_TMOUT_BOOT * HZ to
jiffies; however, as ATA_TMOUT_BOOT is already in jiffies, multiplying
by HZ makes the value way off.  Fix it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make reset methods complain loud when they fail.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

@verbose was added to ata_reset_fn_t because AHCI complained during
probing if no device was attached to the port.  However, muting
failure message isn't the correct approach.  Reset methods are
responsible for detecting no device condition and finishing
successfully.  Now that AHCI softreset is fixed, kill @verbose.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make setting CBL type responsibility of probeinit.  This allows using
only ap->cbl == ATA_CBL_SATA test in all other parts.  Without this,
ata_down_sata_spd_limit() doesn't work during probe reset.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We must disable local IRQs while holding KM_IRQ0 or KM_IRQ1.  Otherwise, an
IRQ handler could use those kmap slots while this code is using them,
resulting in memory corruption.

Thanks to Nick Orlov <bugfixer@list.ru> for reporting.

Cc: <linuxraid@amcc.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Overriding the whole EH code is a per-transport, not per-host thing.
Move ->eh_strategy_handler to the transport class, same as
->eh_timed_out.

Downside is that scsi_host_alloc can't check for the total lack of EH
anymore, but the transition period from old EH where we needed it is
long gone already.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

All softreset methods are responsible for detecting device presence
and succeed softreset in such cases.  AHCI didn't use to check for
device presence before proceeding with softreset and this caused
unnecessary reset retrials during probing.  This patch adds presence
detection to AHCI softreset.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Convert the ATAPI_ENABLE_DMADIR compile time option needed
by some SATA-PATA bridge to runtime module parameter.
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Now that libata mangles with SControl, it's helpful to print out
SControl in link status message.  Add it.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make libata-core routines which will be used by EH implementation
extern.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A lot of EH codes are about to be added to libata.  Separate out
libata-eh.c.  ata_scsi_timed_out(), ata_scsi_error(),
ata_qc_timeout(), ata_eng_timeout(), ata_eh_qc_complete() and
ata_eh_qc_retry() are moved.  No code is changed by this patch.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

qcs might get retried because of unrelated failure.  e.g. NCQ command
failure causes the whole command set to be aborted.  Decrement
scmd->retries for such retrials to avoid unnecessarily failing
commands.  Note that scmd->retries will be incremented the first time.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add @cdb to ata_exec_internal().  It will be used by new EH.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

TF register might not be directly accessible depending on errors.
e.g. TF of failed NCQ command is in log page 10h.  Make reading TF
responsibility of error handlers.  For the current EH, simply push TF
reading into qc completion functions as they are practically part of
EH.  New EH will fill qc->tf with status registers before complting
qcs.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Current sense generation code does not generate sense error if status
register value doesn't indicate error condition.  However, LLDD's may
indicate errors which 't show up in status register.  Completing such
qc's without generating sense results in successful completion of
failed commands.

Invoke ata_to_sense_error() regardless of status register if
qc->err_mask is not zero such that ata_to_sense_error() generates
default sense error.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The current code passes pointer to ap around and repeatedly performs
ata_qc_from_tag() to access the ongoing qc.  This is unnatural and
makes EH synchronization cumbersome.  Make PIO codes deal with qc
instead of ap.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add a new qc flag ATA_QCFLAG_IO.  This flag gets set for normal IO
commands originating from SCSI midlayer.  This information will be
used by EH to determine transfer speed reconfiguration.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_dev_set_mode() is now responsible for managing ATA_DFLAG_PIO.
Clear it before setting it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_dev_configure() should not clear dynamic device flags determined
elsewhere.  Lower eight bits are reserved for feature flags, define
ATA_DFLAG_CFG_MASK and clear only those bits before configuring
device.  Without this patch, ATA_DFLAG_PIO gets turned off during
revalidation making PIO mode unuseable.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Rename ATA_FLAG_PORT_DISABLED to ATA_FLAG_DISABLED for consistency.
(ATA_FLAG_* are always about ports).
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Kill unused flag ATA_FLAG_IN_EH.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure ata_dev_revalidate() complains on failures and kill
revalidation failure message printed from ata_dev_set_mode().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Report device number on PIO failure.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_bus_probe() now marks failed devices properly and leaves
meaningful transfer mode masks.  This patch makes ata_dev_xfermask()
consider disable devices when determining PIO mode to avoid violating
device selection timing.

While at it, move port-wide resttriction out of device iteration loop
and try to make the function look a bit prettier.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Improve ata_bus_probe() such that configuration failures are handled
better.  Each device is given ATA_PROBE_MAX_TRIES chances, but any
non-transient error (revalidation failure with -ENODEV, configuration
failure with -EINVAL...) disables the device directly.  Any IO error
results in SATA PHY speed down and ata_set_mode() failure lowers
transfer mode.  The last try always puts a device into PIO-0.

After each failure, the whole port is reset to make sure that the
controller and all the devices are in a known and stable state.  The
reset also applies SATA SPD configuration if necessary.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement ata_down_xfermask_limit().  This function manipulates
@dev->pio/mwdma/udma_mask such that the next lower transfer mode is
selected.  This will be used to improve ata_bus_probe() failure
handling and later by EH.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some devices react badly if resets are performed back-to-back.  Give
devices some time to breath and tell user that we're taking a nap.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make ata_drive_probe_reset() use SATA SPD configuration.  Hardreset
will be force if speed renegotiation is necessary.  Also, if a
hardreset fails, PHY speed is stepped down and hardreset is retried
until the lowest speed is reached.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>