Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 20 5月, 2006 21 次提交
  3. 10 5月, 2006 6 次提交
  5. 20 4月, 2006 1 次提交
  7. 15 4月, 2006 12 次提交
    • A
      [SCSI] scsi_scan.c: fix compile warnings · c5f2e640
      由 akpm@osdl.org 提交于 
      drivers/scsi/scsi_scan.c: In function `scsi_probe_and_add_lun':
drivers/scsi/scsi_scan.c:926: warning: unused variable `vend'
drivers/scsi/scsi_scan.c:926: warning: unused variable `mod'
drivers/scsi/scsi_scan.c: At top level:
drivers/scsi/scsi_scan.c:829: warning: `scsi_inq_str' defined but not used

Fix those, tighten up the (somewhat poorly-designed) logging macro and fix
some coding-style warts.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      c5f2e640
    • G
      [SCSI] dc395x: dynamically map scatter-gather for PIO · cdb8c2a6
      由 Guennadi Liakhovetski 提交于 
      The current dc395x driver uses PIO to transfer up to 4 bytes which do not
get transferred by DMA (under unclear circumstances). For this the driver
uses page_address() which is broken on highmem. Apart from this the
actual calculation of the virtual address is wrong (even without highmem).
So, e.g., for reading it reads bytes from the driver to a wrong address
and returns wrong data, I guess, for writing it would just output random
data to the device.

The proper fix, as suggested by many, is to dynamically map data using
kmap_atomic(page, KM_BIO_SRC_IRQ) / kunmap_atomic(virt). The reason why it
has not been done until now, although I've done some preliminary patches
more than a year ago was that nobody interested in fixing this problem was
able to reliably reproduce it. Now it changed - with the help from
Sebastian Frei (CC'ed) I was able to trigger the PIO path. Thus, I was
also able to test and debug it.

There are 4 cases when PIO is used in dc395x - data-in / -out with and
without scatter-gather. I was able to reproduce and test only data-in with
and without SG. So, the data-out path is still untested, but it is also
somewhat simpler than the data-in. Fredrik Roubert (also CC'ed) also had
PIO triggering on his system, and in his case it was data-out without SG.
It would be great if he could test the attached patch on his system, but
even if he cannot, I would still request to apply the patch and just wait
if anybody cries...

Implementation: I put 2 new functions in scsi_lib.c and their declarations
in scsi_cmnd.h. I exported them without _GPL, although, I don't feel
strongly about that - not many drivers are likely to use them. But there
is at least one more - I want to use them in tmscsim.c. Whether these are
the right files for the functions and their declarations - not sure
either. Actually, they are not scsi-specific, so, might go somewhere
around other scattergather magic? They are not platform specific either,
and most SG functions are defined under arch/*/... As these issues were
discussed previously there were some more routines suggested to manipulate
scattergather buffers, I think, some of them were needed around
crypto code... So, might be a common place reasonable, like
lib/scattergather.c? I am open here.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      cdb8c2a6
    • F
      [SCSI] ibmvscsi: convert kmalloc + memset to kcalloc · 4c021dd1
      由 FUJITA Tomonori 提交于 
      Convert kmalloc + memset to kcalloc in ibmvscsi
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NDave Boutcher <sleddog@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      4c021dd1
    • J
      Merge ../scsi-rc-fixes-2.6 · 84d891d6
      由 James Bottomley 提交于 
      Conflicts:

	include/scsi/scsi_devinfo.h

Same number for two BLIST flags:  BLIST_MAX_512 and BLIST_ATTACH_PQ3
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      84d891d6
    • J
      [SCSI] scsi_transport_sas: don't scan a non-existent end device · 7676f83a
      由 James Bottomley 提交于 
      Any end device that can't support any of the scanning protocols
shouldn't be scanned, so set its id to -1 to prevent
scsi_scan_target() being called for it.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      7676f83a
    • M
      [SCSI] iscsi: convert iscsi tcp to libiscsi · 5bb0b55a
      由 Mike Christie 提交于 
      This just converts iscsi_tcp to the lib
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      5bb0b55a
    • M
      [SCSI] iscsi: add libiscsi · 7996a778
      由 Mike Christie 提交于 
      There is a lot of code duplcited between iscsi_tcp
and the upcoming iscsi_iser driver. This patch puts
the duplicated code in a lib. There is more code
to move around but this takes care of the
basics. For iscsi_offload if they use the lib we will
probably move some things around. For example in the
queuecommand we will not assume that the LLD wants
to do queue_work, but it is better to handle that
later when we know for sure what iscsi_offload looks
like (we could probably do this for iscsi_iser though to).

Ideally I would like to get the iscsi_transports modules
to a place where all they really have to do is put data
on the wire, but how to do that will hopefully be more clear
when we see other modules like iscsi_offload. Or maybe
iscsi_offload will not use the lib and it will just be
iscsi_iser and iscsi_tcp and maybe the iscsi_tcp_tgt if that
is allowed in mainline.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      7996a778
    • M
      [SCSI] iscsi: fix up iscsi eh · 30a6c652
      由 Mike Christie 提交于 
      The current iscsi_tcp eh is not nicely setup for dm-multipath
and performs some extra task management functions when they
are not needed.

The attached patch:

- Fixes the TMF issues. If a session is rebuilt
then we do not send aborts.

- Fixes the problem where if the host reset fired, we would
return SUCCESS even though we had not really done anything
yet. This ends up causing problem with scsi_error.c's TUR.

- If someone has turned on the userspace nop daemon code to try
and detect network problems before the scsi command timeout
we can now drop and clean up the session before the scsi command
timesout and fires the eh speeding up the time it takes for a
command to go from one patch to another. For network problems
we fail the command with DID_BUS_BUSY so if failfast is set
scsi_decide_disposition fails the command up to dm for it to
try on another path.

- And we had to add some basic iscsi session block code. Previously
if we were trying to repair a session we would retrun a MLQUEUE code
in the queuecommand. This worked but it was not the most efficient
or pretty thing to do since it would take a while to relogin
to the target. For iscsi_tcp/open-iscsi a lot of the iscsi error handler
is in userspace the block code is pretty bare. We will be
adding to that for qla4xxx.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      30a6c652
    • M
      [SCSI] iscsi: add sysfs attrs for uspace sync up · fd7255f5
      由 Mike Christie 提交于 
      For iscsi boot when going from initramfs to the real root we
need to stop the userpsace iscsi daemon. To later restart it
iscsid needs to be able to rebuild itself and part of that
process is matching a session running the kernel with the
iscsid representation. To do this the attached patch
adds several required iscsi values. If the LLD does not provide
them becuase, login is done in userspace, then the transport
class and userspace set ths up for the LLD.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      fd7255f5
    • M
      [SCSI] iscsi: rm kernel iscsi handles usage for session and connection · b5c7a12d
      由 Mike Christie 提交于 
      from hare@suse.de and michaelc@cs.wisc.edu

hw iscsi like qla4xxx does not allocate a host per session and
for userspace it is difficult to restart iscsid using the
"iscsi handles" for the session and connection, so this
patch just has the class or userspace allocate the id for
the session and connection.

Note: this breaks userspace and requires users to upgrade to the newest
open-iscsi tools. Sorry about his but open-iscsi is still too new to
say we have a stable user-kernel api and we were not good nough
designers to know that other hw iscsi drivers and iscsid itself would
need such changes. Actually we sorta did but at the time we did not
have the HW available to us so we could only guess.

Luckily, the only tools hooking into the class are the open-iscsi ones
or other tools like iscsitart hook into the open-iscsi engine from
userspace or prgroams like anaconda call our tools so they are not affected.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      b5c7a12d
    • K
      [SCSI] BLIST_ATTACH_PQ3 flags · 13f7e5ac
      由 Kurt Garloff 提交于 
      Some devices report a peripheral qualifier of 3 for LUN 0; with the original
code, we would still try a REPORT_LUNS scan (if SCSI level is >= 3 or if we
have the BLIST_REPORTLUNS2 passed in), but NOT any sequential scan.
Also, the device at LUN 0 (which is not connected according to the PQ) is not
registered with the OS.

Unfortunately, SANs exist that are SCSI-2 and do NOT support REPORT_LUNS, but
report a unknown device with PQ 3 on LUN 0. We still need to scan them, and
most probably we even need BLIST_SPARSELUN (and BLIST_LARGELUN). See the bug
reference for an infamous example.

This is patch 3/3:
3. Implement the blacklist flag BLIST_ATTACH_PQ3 that makes the scsi
   scanning code register PQ3 devices and continues scanning; only sg
   will attach thanks to scsi_bus_match().
Signed-off-by: NKurt Garloff <garloff@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      13f7e5ac
    • K
      [SCSI] Better log messages for PQ3 devs · 6c7154c9
      由 Kurt Garloff 提交于 
      Some devices report a peripheral qualifier of 3 for LUN 0; with the original
code, we would still try a REPORT_LUNS scan (if SCSI level is >= 3 or if we
have the BLIST_REPORTLUNS2 passed in), but NOT any sequential scan.
Also, the device at LUN 0 (which is not connected according to the PQ) is not
registered with the OS.

Unfortunately, SANs exist that are SCSI-2 and do NOT support REPORT_LUNS, but
report a unknown device with PQ 3 on LUN 0. We still need to scan them, and
most probably we even need BLIST_SPARSELUN (and BLIST_LARGELUN). See the bug
reference for an infamous example.

This patch 2/3:
If a PQ3 device is found, log a message that describes the device
(INQUIRY DATA and C:B:T:U tuple) and make a suggestion for blacklisting
it.
Signed-off-by: NKurt Garloff <garloff@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      6c7154c9