Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 23 2月, 2013 1 次提交
  3. 18 1月, 2013 3 次提交
    • W
      USB: io_ti: Fix NULL dereference in chase_port() · 1ee0a224
      由 Wolfgang Frisch 提交于 
      The tty is NULL when the port is hanging up.
chase_port() needs to check for this.

This patch is intended for stable series.
The behavior was observed and tested in Linux 3.2 and 3.7.1.

Johan Hovold submitted a more elaborate patch for the mainline kernel.

[   56.277883] usb 1-1: edge_bulk_in_callback - nonzero read bulk status received: -84
[   56.278811] usb 1-1: USB disconnect, device number 3
[   56.278856] usb 1-1: edge_bulk_in_callback - stopping read!
[   56.279562] BUG: unable to handle kernel NULL pointer dereference at 00000000000001c8
[   56.280536] IP: [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35
[   56.281212] PGD 1dc1b067 PUD 1e0f7067 PMD 0
[   56.282085] Oops: 0002 [#1] SMP
[   56.282744] Modules linked in:
[   56.283512] CPU 1
[   56.283512] Pid: 25, comm: khubd Not tainted 3.7.1 #1 innotek GmbH VirtualBox/VirtualBox
[   56.283512] RIP: 0010:[<ffffffff8144e62a>]  [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35
[   56.283512] RSP: 0018:ffff88001fa99ab0  EFLAGS: 00010046
[   56.283512] RAX: 0000000000000046 RBX: 00000000000001c8 RCX: 0000000000640064
[   56.283512] RDX: 0000000000010000 RSI: ffff88001fa99b20 RDI: 00000000000001c8
[   56.283512] RBP: ffff88001fa99b20 R08: 0000000000000000 R09: 0000000000000000
[   56.283512] R10: 0000000000000000 R11: ffffffff812fcb4c R12: ffff88001ddf53c0
[   56.283512] R13: 0000000000000000 R14: 00000000000001c8 R15: ffff88001e19b9f4
[   56.283512] FS:  0000000000000000(0000) GS:ffff88001fd00000(0000) knlGS:0000000000000000
[   56.283512] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[   56.283512] CR2: 00000000000001c8 CR3: 000000001dc51000 CR4: 00000000000006e0
[   56.283512] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   56.283512] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[   56.283512] Process khubd (pid: 25, threadinfo ffff88001fa98000, task ffff88001fa94f80)
[   56.283512] Stack:
[   56.283512]  0000000000000046 00000000000001c8 ffffffff810578ec ffffffff812fcb4c
[   56.283512]  ffff88001e19b980 0000000000002710 ffffffff812ffe81 0000000000000001
[   56.283512]  ffff88001fa94f80 0000000000000202 ffffffff00000001 0000000000000296
[   56.283512] Call Trace:
[   56.283512]  [<ffffffff810578ec>] ? add_wait_queue+0x12/0x3c
[   56.283512]  [<ffffffff812fcb4c>] ? usb_serial_port_work+0x28/0x28
[   56.283512]  [<ffffffff812ffe81>] ? chase_port+0x84/0x2d6
[   56.283512]  [<ffffffff81063f27>] ? try_to_wake_up+0x199/0x199
[   56.283512]  [<ffffffff81263a5c>] ? tty_ldisc_hangup+0x222/0x298
[   56.283512]  [<ffffffff81300171>] ? edge_close+0x64/0x129
[   56.283512]  [<ffffffff810612f7>] ? __wake_up+0x35/0x46
[   56.283512]  [<ffffffff8106135b>] ? should_resched+0x5/0x23
[   56.283512]  [<ffffffff81264916>] ? tty_port_shutdown+0x39/0x44
[   56.283512]  [<ffffffff812fcb4c>] ? usb_serial_port_work+0x28/0x28
[   56.283512]  [<ffffffff8125d38c>] ? __tty_hangup+0x307/0x351
[   56.283512]  [<ffffffff812e6ddc>] ? usb_hcd_flush_endpoint+0xde/0xed
[   56.283512]  [<ffffffff8144e625>] ? _raw_spin_lock_irqsave+0x14/0x35
[   56.283512]  [<ffffffff812fd361>] ? usb_serial_disconnect+0x57/0xc2
[   56.283512]  [<ffffffff812ea99b>] ? usb_unbind_interface+0x5c/0x131
[   56.283512]  [<ffffffff8128d738>] ? __device_release_driver+0x7f/0xd5
[   56.283512]  [<ffffffff8128d9cd>] ? device_release_driver+0x1a/0x25
[   56.283512]  [<ffffffff8128d393>] ? bus_remove_device+0xd2/0xe7
[   56.283512]  [<ffffffff8128b7a3>] ? device_del+0x119/0x167
[   56.283512]  [<ffffffff812e8d9d>] ? usb_disable_device+0x6a/0x180
[   56.283512]  [<ffffffff812e2ae0>] ? usb_disconnect+0x81/0xe6
[   56.283512]  [<ffffffff812e4435>] ? hub_thread+0x577/0xe82
[   56.283512]  [<ffffffff8144daa7>] ? __schedule+0x490/0x4be
[   56.283512]  [<ffffffff8105798f>] ? abort_exclusive_wait+0x79/0x79
[   56.283512]  [<ffffffff812e3ebe>] ? usb_remote_wakeup+0x2f/0x2f
[   56.283512]  [<ffffffff812e3ebe>] ? usb_remote_wakeup+0x2f/0x2f
[   56.283512]  [<ffffffff810570b4>] ? kthread+0x81/0x89
[   56.283512]  [<ffffffff81057033>] ? __kthread_parkme+0x5c/0x5c
[   56.283512]  [<ffffffff8145387c>] ? ret_from_fork+0x7c/0xb0
[   56.283512]  [<ffffffff81057033>] ? __kthread_parkme+0x5c/0x5c
[   56.283512] Code: 8b 7c 24 08 e8 17 0b c3 ff 48 8b 04 24 48 83 c4 10 c3 53 48 89 fb 41 50 e8 e0 0a c3 ff 48 89 04 24 e8 e7 0a c3 ff ba 00 00 01 00
<f0> 0f c1 13 48 8b 04 24 89 d1 c1 ea 10 66 39 d1 74 07 f3 90 66
[   56.283512] RIP  [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35
[   56.283512]  RSP <ffff88001fa99ab0>
[   56.283512] CR2: 00000000000001c8
[   56.283512] ---[ end trace 49714df27e1679ce ]---
Signed-off-by: NWolfgang Frisch <wfpub@roembden.net>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      1ee0a224
    • B
      USB: option: add TP-LINK HSUPA Modem MA180 · 99beb2e9
      由 Bjørn Mork 提交于 
      The driver description files gives these names to the vendor specific
functions on this modem:

 Diagnostics VID_2357&PID_0201&MI_00
 NMEA        VID_2357&PID_0201&MI_01
 Modem       VID_2357&PID_0201&MI_03
 Networkcard VID_2357&PID_0201&MI_04
Reported-by: NThomas Schäfer <tschaefer@t-online.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      99beb2e9
    • B
      USB: option: blacklist network interface on ONDA MT8205 4G LTE · 2291dff0
      由 Bjørn Mork 提交于 
      The driver description files gives these names to the vendor specific
functions on this modem:

 Diag   VID_19D2&PID_0265&MI_00
 NMEA   VID_19D2&PID_0265&MI_01
 AT cmd VID_19D2&PID_0265&MI_02
 Modem  VID_19D2&PID_0265&MI_03
 Net    VID_19D2&PID_0265&MI_04
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      2291dff0
  5. 14 1月, 2013 1 次提交
  7. 12 1月, 2013 13 次提交
  9. 08 1月, 2013 2 次提交
  11. 04 1月, 2013 9 次提交
    • G
      Drivers: usb: host: ehci-orion.c: remove __devinitdata marking · 59a609a9
      由 Greg Kroah-Hartman 提交于 
      This snuck in from a different tree during the merge and needs to be
removed.

Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      59a609a9
    • S
      xhci: Avoid "dead ports", add roothub port polling. · c52804a4
      由 Sarah Sharp 提交于 
      The USB core hub thread (khubd) is designed with external USB hubs in
mind.  It expects that if a port status change bit is set, the hub will
continue to send a notification through the hub status data transfer.
Basically, it expects hub notifications to be level-triggered.

The xHCI host controller is designed to be edge-triggered on the logical
'OR' of all the port status change bits.  When all port status change
bits are clear, and a new change bit is set, the xHC will generate a
Port Status Change Event.  If another change bit is set in the same port
status register before the first bit is cleared, it will not send
another event.

This means that the hub code may lose port status changes because of
race conditions between clearing change bits.  The user sees this as a
"dead port" that doesn't react to device connects.

The fix is to turn on port polling whenever a new change bit is set.
Once the USB core issues a hub status request that shows that no change
bits are set in any USB ports, turn off port polling.

We can't allow the USB core to poll the roothub for port events during
host suspend because if the PCI host is in D3cold, the port registers
will be all f's.  Instead, stop the port polling timer, and
unconditionally restart it when the host resumes.  If there are no port
change bits set after the resume, the first call to hub_status_data will
disable polling.

This patch should be backported to stable kernels with the first xHCI
support, 2.6.31 and newer, that include the commit
0f2a7930 "USB: xhci: Root hub support."
There will be merge conflicts because the check for HC_STATE_SUSPENDED
was moved into xhci_suspend in 3.8.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
      c52804a4
    • S
      USB: Handle warm reset failure on empty port. · 65bdac5e
      由 Sarah Sharp 提交于 
      An empty port can transition to either Inactive or Compliance Mode if a
newly connected USB 3.0 device fails to link train.  In that case, we
issue a warm reset.  Some devices, such as John's Roseweil eusb3
enclosure, slip back into Compliance Mode after the warm reset.

The current warm reset code does not check for device connect status on
warm reset completion, and it incorrectly reports the warm reset
succeeded.  This causes the USB core to attempt to send a Set Address
control transfer to a port in Compliance Mode, which will always fail.

Make hub_port_wait_reset check the current connect status and link state
after the warm reset completes.  Return a failure status if the device
is disconnected or the link state is Compliance Mode or SS.Inactive.

Make hub_events disable the port if warm reset fails.  This will disable
the port, and then bring it back into the RxDetect state.  Make the USB
core ignore the connect change until the device reconnects.

Note that this patch does NOT handle connected devices slipping into the
Inactive state very well.  This is a concern, because devices can go
into the Inactive state on U1/U2 exit failure.  However, the fix for
that case is too large for stable, so it will be submitted in a separate
patch.

This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72 "usbcore: refine warm
reset logic"
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NJohn Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
      65bdac5e
    • S
      USB: Ignore port state until reset completes. · 4f43447e
      由 Sarah Sharp 提交于 
      The port reset code bails out early if the current connect status is
cleared (device disconnected).  If we're issuing a hot reset, it may
also look at the link state before the reset is finished.

Section 10.14.2.6 of the USB 3.0 spec says that when a port enters the
Error state or Resetting state, the port connection bit retains the
value from the previous state.  Therefore we can't trust it until the
reset finishes.  Also, the xHCI spec section 4.19.1.2.5 says software
shall ignore the link state while the port is resetting, as it can be in
an unknown state.

The port state during reset is also unknown for USB 2.0 hubs.  The hub
sends a reset signal by driving the bus into an SE0 state.  This
overwhelms the "connect" signal from the device, so the port can't tell
whether anything is connected or not.

Fix the port reset code to ignore the port link state and current
connect bit until the reset finishes, and USB_PORT_STAT_RESET is
cleared.

Remove the check for USB_PORT_STAT_C_BH_RESET in the warm reset case,
because it's redundant.  When the warm reset finishes, the port reset
bit will be cleared at the same time USB_PORT_STAT_C_BH_RESET is set.
Remove the now-redundant check for a cleared USB_PORT_STAT_RESET bit
in the code to deal with the finished reset.

This patch should be backported to all stable kernels.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
      4f43447e
    • S
      USB: Increase reset timeout. · 77c7f072
      由 Sarah Sharp 提交于 
      John's NEC 0.96 xHCI host controller needs a longer timeout for a warm
reset to complete.  The logs show it takes 650ms to complete the warm
reset, so extend the hub reset timeout to 800ms to be on the safe side.

This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72 "usbcore: refine
warm reset logic".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NJohn Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
      77c7f072
    • S
      USB: Allow USB 3.0 ports to be disabled. · 41e7e056
      由 Sarah Sharp 提交于 
      If hot and warm reset fails, or a port remains in the Compliance Mode,
the USB core needs to be able to disable a USB 3.0 port.  Unlike USB 2.0
ports, once the port is placed into the Disabled link state, it will not
report any new device connects.  To get device connect notifications, we
need to put the link into the Disabled state, and then the RxDetect
state.

The xHCI driver needs to atomically clear all change bits on USB 3.0
port disable, so that we get Port Status Change Events for future port
changes.  We could technically do this in the USB core instead of in the
xHCI roothub code, since the port state machine can't advance out of the
disabled state until we set the link state to RxDetect.  However,
external USB 3.0 hubs don't need this code.  They are level-triggered,
not edge-triggered like xHCI, so they will continue to send interrupt
events when any change bit is set.  Therefore it doesn't make sense to
put this code in the USB core.

This patch is part of a series to fix several reports of infinite loops
on device enumeration failure.  This includes John, when he boots with
a USB 3.0 device (Roseweil eusb3 enclosure) attached to his NEC 0.96
host controller.  The fix requires warm reset support, so it does not
make sense to backport this patch to stable kernels without warm reset
support.

This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72 "usbcore: refine warm
reset logic"
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NJohn Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
      41e7e056
    • S
      USB: Ignore xHCI Reset Device status. · 8b8132bc
      由 Sarah Sharp 提交于 
      When the USB core finishes reseting a USB device, the xHCI driver sends
a Reset Device command to the host.  The xHC then updates its internal
representation of the USB device to the 'Default' device state.  If the
device was already in the Default state, the xHC will complete the
command with an error status.

If a device needs to be reset several times during enumeration, the
second reset will always fail because of the xHCI Reset Device command.
This can cause issues during enumeration.

For example, usb_reset_and_verify_device calls into hub_port_init in a
loop.  Say that on the first call into hub_port_init, the device is
successfully reset, but doesn't respond to several set address control
transfers.  Then the port will be disabled, but the udev will remain in
tact.  usb_reset_and_verify_device will call into hub_port_init again.

On the second call into hub_port_init, the device will be reset, and the
xHCI driver will issue a Reset Device command.  This command will fail
(because the device is already in the Default state), and
usb_reset_and_verify_device will fail.  The port will be disabled, and
the device won't be able to enumerate.

Fix this by ignoring the return value of the HCD reset_device callback.

This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72 "usbcore: refine
warm reset logic".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
      8b8132bc
    • S
      USB: Handle auto-transition from hot to warm reset. · 1c7439c6
      由 Sarah Sharp 提交于 
      USB 3.0 hubs and roothubs will automatically transition a failed hot
reset to a warm (BH) reset.  In that case, the warm reset change bit
will be set, and the link state change bit may also be set.  Change
hub_port_finish_reset to unconditionally clear those change bits for USB
3.0 hubs.  If these bits are not cleared, we may lose port change events
from the roothub.

This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72 "usbcore: refine
warm reset logic".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
      1c7439c6
    • S
      xhci: Handle HS bulk/ctrl endpoints that don't NAK. · 55c1945e
      由 Sarah Sharp 提交于 
      A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK.  If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).

The xHCI code to compute the NAK interval does not handle the special
case of zero properly.  The current code unconditionally subtracts one
from bInterval and uses it as an exponent.  This causes a very large
bInterval to be used, and warning messages like these will be printed:

usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes

This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.

This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4a "USB: xhci - fix math in
xhci_get_endpoint_interval()".
Reported-by: NVincent Pelletier <plr.vincent@gmail.com>
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
      55c1945e
  13. 18 12月, 2012 2 次提交
  15. 17 12月, 2012 1 次提交
  17. 13 12月, 2012 8 次提交