In order to dump lan78xx family registers using ethtool, add
support at lan78xx driver level.
Signed-off-by: NRaghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs. Some possible values are:

    0=link/activity          1=link1000/activity
    2=link100/activity       3=link10/activity
    4=link100/1000/activity  5=link10/1000/activity
    6=link10/100/activity    14=off    15=on

These values are given symbolic constants in a dt-bindings header.

Also use the presence of the DT property to indicate that the
LEDs should be enabled - necessary in the event that no valid OTP
or EEPROM is available.
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a standard mechanism for locating and using a MAC address from
the Device Tree. Use this facility in the lan78xx driver to support
applications without programmed EEPROM or OTP. At the same time,
regularise the handling of the different address sources.
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use cpumask_local_spread to provide interrupt affinity hints
for each queue. This will spread interrupts across NUMA local
CPUs first, extending to remote nodes if needed.
Signed-off-by: NBert Kenward <bkenward@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There may be a need for VF driver to request PF to explicitly update its
bulletin with a MAC address.
e.g. When user assigns a MAC address to VF while VF is still down,
and PF's bulletin board contains different MAC address, in this case,
when VF's interface is brought up, it gets loaded with MAC address from
bulletin board which is not desirable.

To handle this corner case, we need a new TLV to request PF to update
its bulletin board with suggested MAC.

This request will be honored only for trusted VFs.
Signed-off-by: NShahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As per existing behavior, when PF sets a MAC address for a VF
(also called as forced MAC), VF is not allowed to change its
MAC address afterwards.
This puts the limitation on few use cases such as bonding of VFs,
where bonding driver asks VF to change its MAC address.

This patch uses a VF trust mode to allow VF to change its MAC address
in spite PF has set a forced MAC for that VF.
Signed-off-by: NShahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, on a new link creation or when 'remote' address parameter
is updated, an MTU is not changed and always equals 1500. When a lower
device has a larger MTU, it might not be efficient, e.g. for UDP, and
requires the manual MTU adjustments to match the MTU of the lower
device.

This patch tries to automate this process, finds a lower device using
the 'remote' address parameter, then uses its MTU to tune GENEVE's MTU:
  * on a new link creation
  * when 'remote' parameter is changed

Also with this patch, the MTU from a user, on a new link creation, is
passed to geneve_change_mtu() where it is verified, and MTU adjustments
with a lower device is skipped in that case. Prior that change, it was
possible to set the invalid MTU values on a new link creation.
Signed-off-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

geneve_change_mtu() will be used not only as ndo_change_mtu() callback,
but also to verify a user specified MTU on a new link creation in the
next patch.
Signed-off-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use ETH_HLEN instead and introduce two new macros: GENEVE_IPV4_HLEN
and GENEVE_IPV6_HLEN that include Ethernet header length, corresponded
IP header length and GENEVE_BASE_HLEN.
Signed-off-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Account for operational state when determining port linkup state,
as per Documentation/networking/operstates.txt.
Signed-off-by: NGeorge Wilkie <gwilkie@vyatta.att-mail.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added the ndo to gather VF statistics through the PF.

Collect VF statistics via mailbox from VF.
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for specifying system controller that configures
phy-mode setting.

According to the DT property "phy-mode", it's necessary to configure the
controller, which is used to choose the settings of the MAC suitable,
for example, mdio pin connections, internal clocks, and so on.

Supported phy-modes are SoC-dependent. The driver allows phy-mode to set
"internal" if the SoC has a built-in PHY, and {"mii", "rmii", "rgmii"}
if the SoC supports each mode. So we have to check whether the phy-mode
is valid or not.

This adds the following features for each SoC:
- check whether the SoC supports the specified phy-mode
- configure the controller accroding to phy-mode

The DT property accepts one argument to distinguish them for multiple MAC
instances.

ethernet@65000000 {
	...
	socionext,syscon-phy-mode = <&soc_glue 0>;
};

ethernet@65200000 {
	...
	socionext,syscon-phy-mode = <&soc_glue 1>;
};
Signed-off-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the link is becoming up for Pro4 SoC, the kernel is stalled
due to some missing clocks and resets.

The AVE block for Pro4 is connected to the GIO bus in the SoC.
Without its clock/reset, the access to the AVE register makes the
system stall.

In the same way, another MAC clock for Giga-bit Connection and
the PHY clock are also required for Pro4 to activate the Giga-bit feature
and to recognize the PHY.

To satisfy these requirements, this patch adds support for multiple clocks
and resets, and adds the clock-names and reset-names to the binding because
we need to distinguish clock/reset for the AVE main block and the others.

Also, make the resets a required property. Currently, "reset is
optional" relies on that the bootloader or firmware has deasserted
the reset before booting the kernel.  Drivers should work without
such expectation.

Fixes: 4c270b55 ("net: ethernet: socionext: add AVE ethernet driver")
Suggested-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mdiobus_register will search for any mdiobus board info registered for
the bus being registered. If found, it will probe devices on the bus.
That device, if for example it is an ethernet switch, may then try to
register an mdio bus. Thus we need to allow recursive calls to
mdiobus_register.

Holding the mdio_board_lock will cause a deadlock during this
recursion. Release the lock and use list_for_each_entry_safe.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add platform device driver to populate the ax88796 platform data from
information provided by the XSurf100 zorro device driver. The ax88796
module will be loaded through this module's probe function.
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The net device struct pointer is stored as platform device drvdata on
module probe - clear the drvdata entry on probe fail there, as well as
when unloading the module.
Signed-off-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the Amiga X-Surf100, the network card interrupt is shared with many
other interrupt sources, so requires the IRQF_SHARED flag to register.
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To be able to tell the ax88796 driver whether it is sensible to enter
the 8390 interrupt handler, an "is this interrupt caused by the 88796"
callback has been added to the ax_plat_data structure (with NULL being
compatible to the previous behaviour).
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add platform specific hooks for block transfer reads/writes of packet
buffer data, superseding the default provided ax_block_input/output.
Currently used for m68k Amiga XSurf100.
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This complements the fix in 82533ad9 ("net: ethernet: ax88796:
don't call free_irq without request_irq first") that removed the
free_irq call in the error path of probe, to also not call free_irq
when remove is called to revert the effects of probe.

Fixes: 82533ad9 (net: ethernet: ax88796: don't call free_irq without request_irq first)
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: NMichael Schmitz <schmitzmic@gmail.com>
Reviewed-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call ax_mii_init in ax_open(), and unregister/remove mdiobus resources
in ax_close().

This is needed to be able to unload the module, as the module is busy
while the MII bus is attached.
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: NMichael Schmitz <schmitzmic@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To read the MAC address from the (virtual) SAprom, the remote DMA
unit needs to be set up like for every other process access to card-local
memory.
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Asix Electronics PHY found on the X-Surf 100 Amiga Zorro network
card by Individual Computers is buggy, and needs the reset bit toggled
as workaround to make a PHY soft reset succeed.

Add workaround driver just for this special case.

Suggested in xsurf100 patch series review by Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NMichael Schmitz <schmitzmic@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The platform data header file is now unused. Remove it, but add
an extra include which it brought in.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GPIOs are described in device tree using a list, without names.
Add defines to indicate what each index in the list means. These
defines should also be used by platform devices passing GPIOs via a
GPIO lookup table.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The same parsing code can be used for both OF and platform devices, if
the platform device uses a gpiod_lookup_table. Parse these properties
directly into the bitbang structure, rather than use an intermediate
platform data structure.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moving the allocation of this structure to the probe function is a
step towards making it the core data structure of the driver.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This simplifies the code, removing the need to handle active low
flags, etc.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No current devices use IRQs in platform data, so remove support for
it. The MDIO core will also initialise the new bus such that all
addresses are polled, so remove the unneeded re-initialisation.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mdio-gpio driver was the only user of the interface reset option.
Since it no longer uses it, remove it from the bit banging code.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The platform data can contain a function to call to reset
the bit banging interface. It is not used, so remove it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Seems like an old typ0.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the prefix for fib6_info struct elements from rt6i_ to fib6_.
rt6i_pcpu and rt6i_exception_bucket are left as is given that they
point to rt6_info entries.

Rename only; not functional change intended.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables arm64 platform support for the HINIC driver.
Signed-off-by: NZhao Chen <zhaochen6@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the NetVSP v6 and 6.1 message structures, and includes
these versions into NetVSC/NetVSP version negotiation process.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implement the 'Device Naming' feature of the Hyper-V
network device API. In Hyper-V on the host through the GUI or PowerShell
it is possible to enable the device naming feature which causes
the host to make available to the guest the name of the device.
This shows up in the RNDIS protocol as the friendly name.

The name has no particular meaning and is limited to 256 characters.
The value can only be set via PowerShell on the host, but could
be scripted for mass deployments. The default value is the
string 'Network Adapter' and since that is the same for all devices
and useless, the driver ignores it.

In Windows, the value goes into a registry key for use in SNMP
ifAlias. For Linux, this patch puts the value in the network
device alias property; where it is visible in ip tools and SNMP.

The host provided ifAlias is just a suggestion, and can be
overridden by later ip commands.

Also requires exporting dev_set_alias in netdev core.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the chip configuration entries only RTL8169 (ver <= 06)
supports tx checksumming for jumbo packets.
By the way: constant JUMBO_1K is a little misleading because it refers
to the standard packet size and not to a jumbo packet size.

By implementing this rule we can get rid of configuring tx checksumming
support per chip type.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>