Add a new bnxt_hwrm_nvm_get_dev_info() to query firmware version
information via NVM_GET_DEV_INFO firmware command.  Use it to
get the running version of the NVM configuration information.

This new function will also be used in subsequent patches to get the
stored firmware versions.
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-8-git-send-email-michael.chan@broadcom.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Currently, the driver will schedule RX ring reset when we get a buffer
error in the RX completion record.  These RX buffer errors can be due
to normal out-of-buffer conditions or a permanent error in the RX
ring.  Because the driver cannot distinguish between these 2
conditions, we assume all these buffer errors require reset.

This is very disruptive when it is just a normal out-of-buffer
condition.  Newer firmware will now monitor the rings for the permanent
failure and will send a notification to the driver when it happens.
This allows the driver to reset only when such a notification is
received.  In environments where we have predominently out-of-buffer
conditions, we now can avoid these unnecessary resets.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a per ring rx_resets counter to count these RX resets.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware now supports device independent discovery of the status
register location. This status register can provide more detailed
information about firmware errors, especially if problems occur
before the HWRM interface is functioning. Attempt to map this
register if it is present and report the firmware status on firmware
init failures.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This feature allows the user to set the different FEC modes on the NIC
port.  Any new setting will take effect immediately after a link toggle.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement .get_fecparam() method to report the configured and active FEC
settings.  Also report the supported and advertised FEC settings to
the .get_link_ksettings() method.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some 200G dual port NICs, if one port is configured to 200G,
firmware will disable the ethernet link on the other port.  Firmware
will send notification to the driver for the disabled port when this
happens.  Define a new field in the link_info structure to keep track
of this state.  The new phy_state field replaces the unused loop_back
field.

Log a message when the phy_state changes state.  In the disabled state,
disallow any PHY configurations on the disabled port as the firmware
will fail all calls to configure the PHY in this state.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware interface has added support for new link speeds using
PAM4 modulation.  Expand the bnxt_link_info structure to closely
mirror the new firmware structures.  Add logic to copy the PAM4
capabilities and settings from the firmware.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG
response size reduction, and a new counter added to
ctx_hw_stats_ext struct to support the new 58818 chip.

The ctx_hw_stats_ext structure is now the superset supporting the new
58818 chips and the prior P5 chips.  Add a new flag to identify the new
chip and use constants for the chip specific ring statistics sizes
instead of the size of the structure.

Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back
to 96 bytes, the workaround added earlier to limit the size of this
message for forwarding to the VF can be removed.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the driver goes through PCIe AER reset in error state, all
firmware messages will timeout because the PCIe bus is no longer
accessible.  This can lead to AER reset taking many minutes to
complete as each firmware command takes time to timeout.

Define a new macro BNXT_NO_FW_ACCESS() to skip these firmware messages
when either firmware is in fatal error state or when
pci_channel_offline() is true.  It now takes a more reasonable 20 to
30 seconds to complete AER recovery.

Fixes: b4fff207 ("bnxt_en: Do not send firmware messages if firmware is in error state.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Add support to dump PXP registers and PCIe statistics.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now we can report all the full 64-bit CPU endian software accumulated
counters instead of the hw counters, some of which may be less than
64-bit wide.  Define the necessary macros to access the software
counters.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have the infrastructure in place, add the new function
bnxt_accumulate_all_stats() to periodically accumulate and check for
counter rollover of all ring stats and port stats.

A chip bug was also discovered that could cause some ring counters to
become 0 during DMA.  Workaround by ignoring zeros on the affected
chips.

Some older frimware will reset port counters during ifdown.  We need
to check for that and free the accumulated port counters during ifdown
to prevent bogus counter overflow detection during ifup.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of these DMAed hardware counters are not full 64-bit counters and
so we need to accumulate them as they overflow.  Allocate copies of these
DMA statistics memory blocks with the same size for accumulation.  The
hardware counter widths are also counter specific so we allocate
memory for masks that correspond to each counter.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver manages multiple statistics structures of different sizes.
They are all allocated, freed, and handled practically the same.  Define
a new bnxt_stats_mem structure and common allocation and free functions
for all staistics memory blocks.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The port statistics structures have hard coded padding and offset.
Define macros to make this look cleaner.
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Main changes are 200G support and fixing the definitions of discard and
error counters to match the hardware definitions.

Because the HWRM_PORT_PHY_QCFG message size has now exceeded the max.
encapsulated response message size of 96 bytes from the PF to the VF,
we now need to cap this message to 96 bytes for forwarding.  The forwarded
response only needs to contain the basic link status and speed information
and can be capped without adding the new information.

v2: Fix bnxt_re compile error.

Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove PCIe non-counters display from ethtool statistics, as
they are not simple counters but register dump.  The next few
patches will add logic to detect counter roll-over and it won't
work with these PCIe non-counters.

There will be a follow up patch to get PCIe information via
ethtool register dump.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert to new infra, taking advantage of sleeping in callbacks.

v2:
 - use bp->*_fw_dst_port_id != INVALID_HW_RING_ID as indication
   that the offload is active.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bare-metal use cases require giving firmware and the embedded
application processor control over VLAN offloads. The driver should
not attempt to override or utilize this feature in such scenarios
since it will not work as expected.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware VLAN offload feature on our NIC does not have separate
knobs for handling customer and service tags on RX. Either offloading
of both must be enabled or both must be disabled. Introduce definitions
for the combined feature set in order to clean up the code and make
this constraint more clear. Technically these features can be separately
enabled on TX, however, since the default is to turn both on, the
combined TX feature set is also introduced for code consistency.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some chips, this varies based on the number of RX rings.  Add this
helper function and refactor the existing code to use it.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently does not keep track of the logical RSS indirection
table.  The hardware RSS table is set up with standard default ring
distribution when initializing the chip.  This makes it difficult to
support user sepcified indirection table entries.  As a first step, add
the logical table in the main bnxt structure and allocate it according
to chip specific table size.  Add a function that sets up default
RSS distribution based on the number of RX rings.

v4: Use bnxt_get_rxfh_indir_size() for the current RSS table size.

v2: Use kmalloc_array() since we init. all entries afterwards.
    Use ALIGN() to roundup the RSS table size.
    Use ethtool_rxfh_indir_default() to init. the default entries.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, we allocate one page for the hardware DMA RSS indirection
table.  While the size is currently big enough for all chips, future
chip variations may support bigger sizes, so it is better to calculate
and store the chip specific size and allocate accordingly.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Older firmware may not support legacy TX push properly and may not
be disabling it.  So we check certain firmware versions that may
have this problem and disable legacy TX push unconditionally.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently only store the firmware version as a string for ethtool
and devlink info.  Store it also as a version code.  The next 2
patches will need to check the firmware major version to determine
some workarounds.

We also use the 16-bit firmware version fields if the firmware is newer
and provides the 16-bit fields.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The explicit mask and shift is not the appropriate way to parse fields
out of a little endian struct. The length field is internally __le16
and the strategy employed only happens to work on little endian machines
because the offset used is actually incorrect (length is at offset 6).

Also remove the related and no longer used definitions from bnxt.h.

Fixes: 845adfe4 ("bnxt_en: Improve valid bit checking in firmware response message.")
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently have 3 software ring counters, rx_l4_csum_errors,
rx_buf_errors, and missed_irqs.  The 1st two are RX counters and the
last one is a common counter.  Organize them into 2 structures
bnxt_rx_sw_stats and bnxt_cmn_sw_stats.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read the L2 doorbell size from the firmware and only map the portion
of the doorbell BAR for L2 use.  This will leave the remaining doorbell
BAR available for the RoCE driver to use.  The RoCE driver can map
the remaining portion as write-combining to support the push feature.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define the 57500 chip doorbell offsets instead of using the magic
values in the C file.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer firmware spec. will specify the number of TQM rings to allocate
context memory for.  Use the firmware specified value and fall back
to the old value derived from bp->max_q if it is not available.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the logic that sets the enable/disable flag for the source MAC
filter according to firmware spec 1.7.1.

In the original firmware spec. before 1.7.1, the VF spoof check flags
were not latched after making the HWRM_FUNC_CFG call, so there was a
need to keep the func_flags so that subsequent calls would perserve
the VF spoof check setting.  A change was made in the 1.7.1 spec
so that the flags became latched.  So we now set or clear the anti-
spoof setting directly without retrieving the old settings in the
stored vf->func_flags which are no longer valid.  We also remove the
unneeded vf->func_flags.

Fixes: 8eb992e8 ("bnxt_en: Update firmware interface spec to 1.7.6.2.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store the part number and serial number information from VPD in
the bnxt structure. Follow up patch will add the support to display
the information via devlink command.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Display the minimum version of firmware interface spec supported
between driver and firmware. Also update bnxt.rst documentation file.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an indexing bug in determining these ethtool priority
counters.  Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index.  This index is then used
to obtain the proper CoS queue counter.  Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.

Fixes: e37fed79 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use linux kernel version for ethtool and module versions.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of switch_id, renaming it to dsn will be more meaningful
so that it can be used to display device serial number in follow up
patch via devlink_info command.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware bug has been fixed on B0 and newer chips, so disable the
workaround on these chips.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSN read can fail, for example on a kdump kernel without PCIe extended
config space support.  If DSN read fails, don't set the
BNXT_FLAG_DSN_VALID flag and continue loading.  Check the flag
to see if the stored DSN is valid before using it.  Only VF reps
creation should fail without valid DSN.

Fixes: 03213a99 ("bnxt: move bp->switch_id initialization to PF probe")
Reported-by: NMarc Smith <msmith626@gmail.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>