The MV88E6220 is almost the same as MV88E6250 except that the ports 2-4 are
not routed to pins. So the usable ports are 0, 1, 5 and 6.
Signed-off-by: NHubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ensures we can talk to a PHY via MDIO on the AST2600, as the MDIO
controller is now separate from the MAC.
Signed-off-by: NAndrew Jeffery <andrew@aj.id.au>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy-handle is necessary for the AST2600 which separates the MDIO
controllers from the MAC.

I've tried to minimise the intrusion of supporting the AST2600 to the
FTGMAC100 by leaving in place the existing MDIO support for the embedded
MDIO interface. The AST2400 and AST2500 continue to be supported this
way, as it avoids breaking/reworking existing devicetrees.

The AST2600 support by contrast requires the presence of the phy-handle
property in the MAC devicetree node to specify the appropriate PHY to
associate with the MAC. In the event that someone wants to specify the
MDIO bus topology under the MAC node on an AST2400 or AST2500, the
current auto-probe approach is done conditional on the absence of an
"mdio" child node of the MAC.
Signed-off-by: NAndrew Jeffery <andrew@aj.id.au>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AST2600 design separates the MDIO controllers from the MAC, which is
where they were placed in the AST2400 and AST2500. Further, the register
interface is reworked again, so now we have three possible different
interface implementations, however this driver only supports the
interface provided by the AST2600. The AST2400 and AST2500 will continue
to be supported by the MDIO support embedded in the FTGMAC100 driver.

The hardware supports both C22 and C45 mode, but for the moment only C22
support is implemented.
Signed-off-by: NAndrew Jeffery <andrew@aj.id.au>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Wrapping mv88e6xxx_vtu_getnext makes the code less easy to read and
_mv88e6xxx_port_vlan_add is the only function requiring the preparation
of a new VLAN entry.

To simplify things up, remove the mv88e6xxx_vtu_get wrapper and
explicit the VLAN lookup in _mv88e6xxx_port_vlan_add. This rework
also avoids programming the broadcast entries again when changing a
port's membership, e.g. from tagged to untagged.

At the same time, rename the helper using an old underscore convention.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Wrapping mv88e6xxx_vtu_getnext makes the code less easy to read.
Explicit the call to mv88e6xxx_vtu_getnext in _mv88e6xxx_port_vlan_del
and the return value expected by switchdev in case of software VLANs.

At the same time, rename the helper using an old underscore convention.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mv88e6xxx_vtu_getnext is simple enough to call it directly in the
mv88e6xxx_port_db_load_purge function and explicit the return code
expected by switchdev for software VLANs when an hardware VLAN does
not exist.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mv88e6xxx_vtu_getnext interprets two members from the input
mv88e6xxx_vtu_entry structure: the (excluded) vid member to start
the iteration from, and the valid argument specifying whether the VID
must be written or not (only required once at the start of a loop).

Explicit the assignation of these two fields right before calling
mv88e6xxx_vtu_getnext, as it is done in the mv88e6xxx_vtu_get wrapper.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lock the mutex in the mv88e6xxx_port_vlan_prepare function
called by the DSA stack, instead of doing it in the internal
mv88e6xxx_port_check_hw_vlan helper.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When calling hclge_reset_event() within HCLGE_RESET_INTERVAL,
it returns directly now. If no one call it again, then the
error which needs a reset to fix it can not be fixed.

So this patch activates the reset timer for this case, and
adds checking in the end of the reset procedure to make this
error fixed earlier.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the reset interrupt is cleared in the reset task, which
is too late. Since, when the hardware finish the previous reset,
it can begin to do a new global/IMP reset, if this new coming reset
type is same as the previous one, the driver will clear them together,
then driver can not get that there is another reset, but the hardware
still wait for the driver to deal with the second one.

So this patch clears PF's reset interrupt status in the
hclge_irq_handle(), the hardware waits for handshaking from
driver before doing reset, so the driver and hardware deal with reset
one by one.

BTW, when VF doing global/IMP reset, it reads PF's reset interrupt
register to get that whether PF driver's re-initialization is done,
since VF's re-initialization should be done after PF's. So we add
a new command and a register bit to do that. When VF receive reset
interrupt, it sets up this bit, and PF finishes re-initialization
send command to clear this bit, then VF do re-initialization.

Fixes: 4ed340ab ("net: hns3: Add reset process in hclge_main")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the driver sets handshake status to tell the hardware
that the driver have downed the netdev and it can continue with
reset process. The driver will clear the handshake status when
re-initializing the CMDQ, and does not recover this status
when reset fail, which may cause the hardware to wait for
the handshake status to be set and not being able to continue
with reset process.

So this patch delays clearing handshake status just before UP,
and recovers this status when reset fail.

BTW, this patch adds a new function hclge(vf)_reset_handshake() to
deal with the reset handshake issue, and renames
HCLGE(VF)_NIC_CMQ_ENABLE to HCLGE(VF)_NIC_SW_RST_RDY which
represents this register bit more accurately.

Fixes: ada13ee3 ("net: hns3: add handshake with hardware while doing reset")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The member 'mac_add' defined in hclge_mac_ethertype_idx_rd_cmd
means MAC address, so 'mac_addr' is a better name for it.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 4th and 5th parameter of hclge_cmd_query_error is useless, so this
patch removes them.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hclge_tm_schd_info_update calls hclge_tm_schd_info_init to
initialize the schedule info, hdev->tm_info.num_pg and
hdev->tx_sch_mode is not changed, which makes the checking in
hclge_tm_schd_info_init unnecessary.

So this patch moves the hdev->tm_info.num_pg and hdev->tx_sch_mode
checking into hclge_tm_schd_init and changes the return type of
hclge_tm_schd_info_init from int to void.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The unused_count variable is used to indicate how many
RX BD need attaching new buffer in hns3_clean_rx_ring,
and the clean_count variable has the similar meaning.

This patch removes the clean_count variable and use
unused_count to uniformly indicate the RX BD that need
attaching new buffer.

This patch also clean up some coding style related to
variable assignment in hns3_clean_rx_ring.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The local variable return_status in hclge_get_mac_val_cmd_status()
is useless. So this patch returns the error code directly, instead of
using this variable. Also, replace some '%d' with '%u' in
hclge_get_mac_val_cmd_status().
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, when changing the ring parameters, we free the old
ring resources firstly, and then setup the new ring resources.
In some case of an memory allocation fail, there will be no
resources to use. This patch refines it by setup new ring
resources and free the old ring resources in order.

Also reduce the max ring BD number to 32760 according to UM.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some commands are not supported on DCB-unsupported ports.
This patch distinguishes these commands and does not query
unsupported commands in debugfs.

This patch also fix an error in the dump "qos buf cfg"
command in debugfs.

Fixes: 2849d4e7 ("net: hns3: Add "tc config" info query function")
Fixes: 7d9d7f88 ("net: hns3: Add "qos buffer" config info query function")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When NCSI has HW error, the IMP will report this error to the driver
by sending a mailbox. After received this message, the driver should
assert a global reset to fix this kind of HW error.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, PF updates link status per second. For some scenario,
it requires link down event being reported more quickly.
To solve it, firmware pushes the link change event to PF with
CMDQ message, and driver updates the link status directly.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update driver version to 0.7.5
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As a result of refactoring of VF VSIs interrupts code, there is no
need to track its configuration status again with ICE_VF_STATE_CFG_INTR
flag - In fact, it is not being checked anywhere in the code right now, so
this patch removes the dead code as applicable to the flag.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This flag is not needed and is called every time we re-enable interrupts
in the hotpath so remove it. Also remove ice_vsi_req_irq() because it
was a wrapper function for ice_vsi_req_irq_msix() whose sole purpose was
checking the ICE_FLAG_MSIX_ENA flag.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since Tx rings are being managed by FW/NVM, Tx rings might have not been
set up or driver had already wiped them off - In that case, call to
disable LAN Tx queue is being returned as not in existence. This patch
makes sure we don't return unnecessary error for such scenario.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the call to ice_alloc_mapped_page() fails we jump to the
no_buf label, possibly call ice_release_rx_desc(), and return true
indicating that there is more work to do. In the success case we just
fall out of the while loop, possibly call ice_alloc_mapped_page(), and
return false saying we exhausted cleaned_count. This flow can be
improved by breaking if ice_alloc_mapped_page() fails and then the flow
outside of the while loop is the same for the failure and success case.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we are not reporting dropped counts at the port level to
ethtool or netlink. This was found when debugging Rx dropped issues
and the total packets sent did not equal the total packets received
minus the rx_dropped, which was very confusing. To determine dropped
counts at the port level we need to read the PRTRPB_RDPC register.
To fix reporting we will store the dropped counts in the PF's
rx_discards. This will be reported to netlink by storing it in the
PF VSI's rx_missed_errors signaling that the receiver missed the
packet. Also, we will report this to ethtool in the rx_dropped.nic
field.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In case there is a request from a VF to change its number of queues, and
the request was successful, we need to update number of queues
configured on the VF before updating corresponding VSI for that VF,
especially LAN Tx queue tree and TC update, otherwise, we would continued
to use old value of vf->num_vf_qs for allocated Tx/Rx queues...
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch uses allocated number of Tx queues per VSI to set up its
scheduling tree instead of using total number of available Tx queues.
Only PF VSIs have total number of allocated Tx queues equal to number
of available Tx queues, other VSIs have different number of queues
configured.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we bump the Rx tail and release/give buffers to hardware every
16 descriptors. This causes us to bump Rx tail up to 4 times per
napi_poll call. Also we are always bumping tail on an odd index and this
is a problem because hardware ignores the lower 3 bits in the QRX_TAIL
register. This is making it so hardware sees tail bumps only every 8
descriptors. Instead lets only bump Rx tail once per napi_poll if
the value aligns with hardware's expectations of the lower 3 bits being
cleared. Also only release/give Rx buffers once per napi_poll call.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds code to clear VFs enable status until reset is completed,
and Tx/Rx rings are setup. Without this patch, the code flow request Tx
queues to be disabled after reset, especially PFR - where VF VSI Tx rings
have already been wiped off in the NVM and result to adminq error based on
the call to disable Tx LAN queue in ice_reset_all_vfs function call.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The firmware reports an error when trying to configure a port with no
media. Instead of always configuring the port, check for media before
attempting to configure it. In the absence of media, turn off link and
poll for media to become available before re-enabling link.

Move ice_force_phys_link_state() up to avoid forward declaration.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>