Fix for reset which happens right after sending a terminate message.
Terminate timer is not deleted when the connection is closed.
Signed-off-by: NTatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: NFaisal Latif <Faisal.Latif@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Warned about by sparse.
Signed-off-by: NTatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: NFaisal Latif <Faisal.Latif@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Change the PHY clock divisor to make the MDIO clock 2.5MHz, instead of
3.5MHz (which is out of spec).
Signed-off-by: NTatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: NFaisal Latif <Faisal.Latif@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

For IBoE, SLs 0-7 are mapped to Ethernet 802.1Q user priority bits
(pbits) which are part of the VLAN tag, SLs 8-15 are reserved.

Under Ethernet, the ConnectX firmware treats (decode/encode) the four
bit SL field in various constructs such as QPC / UD WQE / CQE as PPP0
and not as 0PPP. This correlates well to the fact that within the
vlan tag the pbits are located in bits 15-13 and not 12-14.

The current code wasn't consistent around that area - the
encoding was correct for the IBoE QPC.path.schedule_queue field,
but was wrong for IBoE CQEs and when MLX header was built.

These inconsistencies resulted in wrong SL <--> wire 802.1Q pbits
mapping, which is fixed by using SL <--> PPP0 all around the place.
Signed-off-by: NOren Duer <oren@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Minimize the need for users to have to set module parameters to get
good performance.

The following two parameters are changed:
 - rcvhdrcnt to twice the rcvegrcnt
 - pcie_caps=0x51

The rcvhdrcnt at twice the egrcount allows the preemptive NAK code
during reception to function in 100% of the cases rather than a sender
jiffies-based timeout.

The pcie_caps default of 0x51 will set the proposed MaxPayload and
MaxReceiveReqest to 256 and 4096 respectively.  The capabilities on
the root complex will be used to limit those values.
Reviewed-by: NRam Vepa <ram.vepa@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The current code locks the QP s_lock, followed by the pending_lock, I
guess to to protect against the allocate failing.

This patch only locks the pending_lock, assuming that the empty case
is an exeception, in which case the pending_lock is dropped, and the
original code is executed.  This will save a lock of s_lock in the
normal case.

The observation is that the sdma descriptors will deplete at twice the
rate of txreq's, so this should be rare.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Prevent a receive data corruption by ensuring that the write to update
the rcvhdrheadn register to generate an interrupt is at the very end
of the receive processing.
Signed-off-by: NRamkrishna Vepa <ram.vepa@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Cc: <stable@kernel.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The qib driver makes use of the the 64-bit jiffies API.

Code inspection reveals that that version of the API is not really
required.  This patch converts to use the "normal" jiffies.
Reviewed-by: NRam Vepa <ram.vepa@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

More style issues revealed with checkpatch.pl -f.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Commit 53ab1c64 ("IB/qib: Correct nfreectxts for multiple HCAs")
reversed the increments and decrements of dd->nfreectxts.  Fix it.
Reviewed-by: NRam Vepa <ram.vepa@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).

This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.

Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Port mask now has additional state.
Port can be set as "none". In this case neither the mlx4_en or mlx4_ib
drivers take ownership of the port.
In multifunction mode there is an option to set the vfs as single ported devices.
(in single function mode, both physical ports belong to same function)
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit cfcde11c ("IB/mlx4: Use flow counters on IBoE ports") added
code that sets elements of counters[] to -1 if no counter is allocated,
but then goes ahead and passes every entry to mlx4_counter_free() on
shutdown.  This is a bad idea, especially if MLX4_DEV_CAP_FLAG_COUNTERS
isn't set so there isn't even an underlying bitmap to free from.
Tested-by: NSean Hefty <sean.hefty@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Three pieces of code do the same thing, create a l2t entry and then
import this information into the c4iw_ep object.

Create a helper function and call it from these 3 locations instead.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NRoland Dreier <roland@purestorage.com>

Do this instead of performing a by-hand lookup.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NRoland Dreier <roland@purestorage.com>

This way we consolidate the RCU locking down into the place where it
actually matters, and also we can make the code handle
dst_get_neighbour_noref() returning NULL properly.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To reflect the fact that a refrence is not obtained to the
resulting neighbour entry.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NRoland Dreier <roland@purestorage.com>

Commit f2c31e32 ("net: fix NULL dereferences in check_peer_redir()")
forgot to take care of infiniband uses of dst neighbours.

Many thanks to Marc Aurele who provided a nice bug report and feedback.
Reported-by: NMarc Aurele La France <tsi@ualberta.ca>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Don't over-schedule QSFP work on driver initialization.  It could end
up being run simultaneously on two different CPUs resulting in bad
EEPROM reads.  In combination with setting the physical IB link state
prior to the IBC being brought out of reset, this can cause the link
state machine to start training early with wrong settings.
Signed-off-by: NMitko Haralanov <mitko@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix logic so that we don't retry with MPAv1 once we have done that
already.  Otherwise, we end up retrying with MPAv1 even when its not
needed on getting peer aborts - and this could lead to kernel panic.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix another place in the code where logic dealing with the t4_cqe was
using the wrong QID.  This fixes the counting logic so that it tests
against the SQ QID instead of the RQ QID when counting RCQES.

Signed-off by: Jonathan Lallinger <jonathan@ogc.us>
Signed-off by: Steve Wise <swise@ogc.us>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was mistakenly introduced by dde05cbd ("IB/qib: Hold links
until tuning data is available").
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The following panic can occur when flushing a QP:

    RIP: 0010:[<ffffffffa0168e8b>]  [<ffffffffa0168e8b>] qib_send_complete+0x3b/0x190 [ib_qib]
    RSP: 0018:ffff8803cdc6fc90  EFLAGS: 00010046
    RAX: 0000000000000000 RBX: ffff8803d84ba000 RCX: 0000000000000000
    RDX: 0000000000000005 RSI: ffffc90015a53430 RDI: ffff8803d84ba000
    RBP: ffff8803cdc6fce0 R08: ffff8803cdc6fc90 R09: 0000000000000001
    R10: 00000000ffffffff R11: 0000000000000000 R12: ffff8803d84ba0c0
    R13: ffff8803d84ba5cc R14: 0000000000000800 R15: 0000000000000246
    FS:  0000000000000000(0000) GS:ffff880036600000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
    CR2: 0000000000000034 CR3: 00000003e44f9000 CR4: 00000000000406f0
    DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
    DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
    Process qib/0 (pid: 1350, threadinfo ffff8803cdc6e000, task ffff88042728a100)
    Stack:
     53544c5553455201 0000000100000005 0000000000000000 ffff8803d84ba000
     0000000000000000 0000000000000000 0000000000000000 0000000000000000
     0000000000000000 0000000000000001 ffff8803cdc6fd30 ffffffffa0165d7a
    Call Trace:
     [<ffffffffa0165d7a>] qib_make_rc_req+0x36a/0xe80 [ib_qib]
     [<ffffffffa0165a10>] ?  qib_make_rc_req+0x0/0xe80 [ib_qib]
     [<ffffffffa01698b3>] qib_do_send+0xf3/0xb60 [ib_qib]
     [<ffffffff814db757>] ? thread_return+0x4e/0x777
     [<ffffffffa01697c0>] ? qib_do_send+0x0/0xb60 [ib_qib]
     [<ffffffff81088bf0>] worker_thread+0x170/0x2a0
     [<ffffffff8108e530>] ?  autoremove_wake_function+0x0/0x40
     [<ffffffff81088a80>] ? worker_thread+0x0/0x2a0
     [<ffffffff8108e1c6>] kthread+0x96/0xa0
     [<ffffffff8100c1ca>] child_rip+0xa/0x20
     [<ffffffff8108e130>] ? kthread+0x0/0xa0
     [<ffffffff8100c1c0>] ? child_rip+0x0/0x20
    RIP  [<ffffffffa0168e8b>] qib_send_complete+0x3b/0x190 [ib_qib]

The RC error state flush logic in qib_make_rc_req() could return all
of the acked wqes and potentially have emptied the queue.  It would
then unconditionally try return a flush completion via
qib_send_complete() for an invalid wqe, or worse a valid one that is
not queued. The panic results when the completion code tries to
maintain an MR reference count for a NULL MR.

This fix modifies logic to only send one completion per
qib_make_rc_req() call and changing the completion status from
IB_WC_SUCCESS to IB_WC_WR_FLUSH_ERR as the completions progress.

The outer loop will call as many times as necessary to flush the queue.
Reviewed-by: NRam Vepa <ram.vepa@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The num_free field of mthca_buddy has a type of array of unsigned int
while it was allocated as an array of pointers.  On 64-bit platforms
this allocates twice more than required.  Fix this by allocating the
correct size for the type.

This is the same bug just fixed in mlx4 by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Some kernel components pin user space memory (infiniband and perf) (by
increasing the page count) and account that memory as "mlocked".

The difference between mlocking and pinning is:

A. mlocked pages are marked with PG_mlocked and are exempt from
   swapping. Page migration may move them around though.
   They are kept on a special LRU list.

B. Pinned pages cannot be moved because something needs to
   directly access physical memory. They may not be on any
   LRU list.

I recently saw an mlockalled process where mm->locked_vm became
bigger than the virtual size of the process (!) because some
memory was accounted for twice:

Once when the page was mlocked and once when the Infiniband
layer increased the refcount because it needt to pin the RDMA
memory.

This patch introduces a separate counter for pinned pages and
accounts them seperately.
Signed-off-by: NChristoph Lameter <cl@linux.com>
Cc: Mike Marciniszyn <infinipath@qlogic.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

These files were getting the moduleparam infrastructure from the
implicit presence of module.h being everywhere, but that is going
away soon.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

These were getting it implicitly via device.h --> module.h but
we are going to stop that when we clean up the headers.

Fix these in advance so the tree remains biscect-clean.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

They had been getting it implicitly via device.h but we can't
rely on that for the future, due to a pending cleanup so fix
it now.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

They get it via module.h (via device.h) but we want to clean that up.
When we do, we'll get things like:

  CC [M]  drivers/infiniband/core/sysfs.o
  sysfs.c:361: error: 'S_IRUGO' undeclared here (not in a function)
  sysfs.c:654: error: 'S_IWUSR' undeclared here (not in a function)

so add in the stat header it is using explicitly in advance.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

There's no need to set the vlan-related fields in an IBoE send WQE
control segment:

 - the vlan to be used by a UD QP is set in the datagram segment.
 - for GSI (CM) QP, all the headers down to 8021q and MAC are built by
   the software anyway.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The IBoE port MTU is derived from the corresponding Ethernet netdevice
MTU, which can support jumbo frames of 9K, and hence surely supports
the max IB mtu of 4K.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

QPs need to be moved to error before telling the firwmare to shutdown
the queue.  Otherwise, the application can submit WRs that will never
get fetched by the hardware and never flushed by the driver.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Acked-by: NSteve Wise <swsie@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Commit 01e7da6b ("RDMA/cxgb4: Make sure flush CQ entries are
collected on connection close") introduced a potential problem where a
CQ's comp_handler can get called simultaneously from different places
in the iw_cxgb4 driver.  This does not comply with
Documentation/infiniband/core_locking.txt, which states that at a
given point of time, there should be only one callback per CQ should
be active.

This problem was reported by Parav Pandit <Parav.Pandit@Emulex.Com>.
Based on discussion between Parav Pandit and Steve Wise, this patch
fixes the above problem by serializing the calls to a CQ's
comp_handler using a spin_lock.
Reported-by: NParav Pandit <Parav.Pandit@Emulex.Com>
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

iw_cxgb3 has a potential problem where a CQ's comp_handler can get
called simultaneously from different places in iw_cxgb3 driver.  This
does not comply with Documentation/infiniband/core_locking.txt, which
states that at a given point of time, there should be only one
callback per CQ should be active.

Such problem was reported by Parav Pandit <Parav.Pandit@Emulex.Com>
for iw_cxgb4 driver.  Based on discussion between Parav Pandit and
Steve Wise, this patch fixes the above problem by serializing the
calls to a CQ's comp_handler using a spin_lock.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix an issue where the link would come up after replugging a cable
even if it has been DISABLED manually.
Signed-off-by: NMitko Haralanov <mitko@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Set the extended active speeds based on the hardware configuration.
Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: NHal Rosenstock <hal@mellanox.com>

[ Move FDR-10 handling into ib_link_query_port().  - Roland ]
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Hold the link state machine until the tuning data is read from the
QSFP EEPROM so correct tuning settings are applied before the state
machine attempts to bring the link up.  Link is also held on cable
unplug in case a different cable is used.
Signed-off-by: NMitko Haralanov <mitko@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>