Add SCLP PCI configure/deconfigure and implement a PCI hotplug
controller (s390_pci_hpc). The hotplug controller creates a slot
for every PCI function in stand-by or configured state. The PCI
functions are named after the PCI function ID (fid). By writing to
the power attribute in /sys/bus/pci/slots/<fid>/power the PCI function
is moved to stand-by or configured state. If moved to the configured
state the device is automatically scanned by the s390 PCI layer.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Move and rename init_storage_keys() to pageattr.c, so it can also be
used from the sclp memory hotplug code in order to initialize
storage keys.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

For processing under KVM it is required to detect
the actual SCLP console type in order to set it as
preferred console.
Signed-off-by: NHeinz Graalfs <graalfs@linux.vnet.ibm.com>
Acked-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Currently qemu/kvm on s390 uses a guest mapping that does not
allow the guest backing page table to be write-protected to
support older systems. On those older systems a host write
protection fault will be delivered to the guest.

Newer systems allow to write-protect the guest backing memory
and let the fault be delivered to the host, thus allowing COW.

Use a capability bit to tell qemu if that is possible.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Acked-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Add missing storage key initialization when memory comes online.
Didn't hurt until now, since the kernel always uses access key 0.

However for debugging purposes we sometimes use a different key
and it might be good if everything is properly initialized...
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Disintegrate asm/system.h for S390.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
cc: linux-s390@vger.kernel.org

Use for_each_clear_bit() to iterate over all the cleared bit in a
memory region.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Split out addressing mode bits from PSW_BASE_BITS, rename PSW_BASE_BITS
to PSW_MASK_BASE, get rid of psw_user32_bits, remove unused function
enabled_wait(), introduce PSW_MASK_USER, and drop PSW_MASK_MERGE macros.
Change psw_kernel_bits / psw_user_bits to contain only the bits that
are always set in the respective mode.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Make sure that only assigned storage increments are unassigned when
attaching a storage element.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Fix initial usecount of attached and assigned storage increments so
they can be set offline.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Avoid 64 bit division to fix this compile error on 32 bit:
drivers/s390/char/sclp_cmd.c:711: undefined reference to `__udivdi3'

Also move the whole arch_get_memory_phys_device function to the
memory hotplug related functions.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Implement arch specific arch_get_memory_phys_device function and
initialize phys_device for each memory section.  That way we finally can
tell which piece of memory belongs to which physical device.

This makes s390's /sys/devices/system/memory/memoryX/phys_device display
the correct thing?
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Set dump indicator on read-scp-info command to get meaningful dumps.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Standby memory detected with the sclp interface gets always registered
with add_memory calls without considering the limitationt that the
"mem=" kernel paramater implies.
So fix this and only register standby memory that is below the specified
limit.
This fixes zfcpdump since it uses "mem=32M". In case there is appr.
2GB standby memory present all of usable memory would be used for the
struct pages needed for standby memory.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch enables memory hot-remove on s390.
Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>

Move memory detection code to own file and also simplify it.
Also add an interface which can be called at any time to get the
current memory layout. This interface is needed by our kernel
internal system dumper.

Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Cc: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

It caused only a lot of confusion. From now on cpu hotplug of up to
NR_CPUS will work by default. If somebody wants to limit that then
the possible_cpus parameter can be used.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add a new interface so that cpus can be put into standby state and
configured state.
Only offline cpus can be put into standby state or configured state.
For that the new percpu sysfs attribute "configure" must be used.
To put a cpu in standby state a "0" must be written to the attribute.
In order to switch it into configured state a "1" must be written to
the attribute.
Only cpus in configured state can be brought online.
In addition this patch introduces a static mapping of physical to
logical cpus. As a result only the sysfs directories of present cpus
will be created. To scan for new cpus the new sysfs attribute "rescan"
must be used.
Writing to /sys/devices/system/cpu/rescan will trigger a rescan of
cpus and will create directories for new cpus.

On IPL only configured cpus will be used. And on reboot/shutdown all
cpus will remain in their current state (configured/standby).
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>