Our testers need to know the number of scans performed while in
net-detect mode before the device wakes up.  The firmware already
passes this information to the driver, so we can save it and report it
in a debugfs entry.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Minor cleanup and refactoring.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we access the triggers we need to make sure that the
data we expect was actually provided by the firmware file.
Check this when we decode the triggers from the firmware
file.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In the reset flow, the driver cancels ongoing scan and sends scan
complete notification to mac80211. However it does not clean its UID.
Add cleaning scan UID for the ongoing scan. Loop over all other UIDs
to make sure there's nothing left there and warn if any is found.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There is a strong relationship between the NVM version and
the hardware step. Enforce that in the driver in case the
default NVM on the platform is the wrong one.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The semaphore may not be accessible. Fix the debug prints
accordingly.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Sometimes we will want to configure the timeouts for the
Tx queues based on the vif type. Allow to do that using the
trigger mechanism.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

These early versions are no longer supported.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There is no need to implement the enable_scan_iteration_notif handling
explicitly and there's no reason not to export the current value.  So
use debugfs_create_bool() instead.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add support for delaying the start of a scheduled scan (or a WoWLAN
net-detect scan).
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ref_count is currently initialized on start_fw(). This causes
some issues in restart flow, as currently active references
(e.g. unclaimed command) will get cleared, resulting in
invalid reference accounting.

Move the ref_count initialization to the configure() trans op,
so it won't be re-initialized on restart.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In nic restart flow we inform mac80211 that scan was aborted, but it was
based only on scan_status which is not set by UMAC scan. Fix that.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The AP_START d0i3 reference was never removed if the AP started correctly.
This has the unpleasant side-effect of preventing D0i3 on Android if the
WiFi hotspot was ever started on the device.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

we unref IWL_MVM_REF_UCODE_DOWN on iwl_mvm_restart_complete().

Usually, the restart is initiated by iwl_mvm_nic_restart(),
which takes the reference before restarting the hw.

However, in D3 flow we might call ieee80211_restart_hw()
directly (in case of suspend error and on d3_test-resume),
which without taking the ref first. fix it.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware has a race in the flow that indicates the
completion of the authentication. Checking the completion
of the authentication is not really needed anyway since
we can wait for the ALIVE notification instead.
Remove the unneeded and buggy code.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This warning is misleading. In many cases, for example P2P ROC time
events, this will happen if the time event is aborted, for example
due to a higher priority time event. This is entirely normal and not
worth warning about.

In other cases, where we actually do act upon this, for example when
trying to connect and this fails, we should instead warn as part of
the disconnect operation.

Change the code to do that, i.e. make the warning a debug message,
and make it more prominent (an error) when we actually disconnect
because of it.

This also fixes confusion in the logs - the warning was mistaken for
something that needed investigation, while in most cases it's just
expected behaviour that occasionally some lower-priority time events
would not complete fully.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In 8000 HW family B-step only, the ICCM is separate
from the SRAM. This adds the ICCM to the dump data
collected for FW debug.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There are transport that must buffer frames in the driver.
This means that we have frames that are not in the op_mode
and not visible to the firwmare. This causes issues when we
flush the queues: the op_mode flushes a queue, and the
firmware flushes all the frames that are *currently* on the
rings, but if the transport buffers frames, it can submit
these while we are flushing. This leads to a situation
where we still have frames on the queues after we flushed
them.
Preventing those buffered frame from getting into the
firmware is possible, but then, we have to run the Tx
response path on frames that didn't reach the firmware
which is not desirable.
The way I solve this here is to let these frames go to the
firmware, but make sure the firmware will not transmit them
(by setting the station as draining). The op_mode then needs
to wait until the transport itself is empty to be sure that
the queue is really empty.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For each RX packet until this patch there only was a debug
print of the HCMD and the offset. This adds also the
sequence number of the packet for easier matching between
what was sent, what came back / was received, and what
got stuck somewhere and was never responded by the FW.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

According to FW methodology, the capability bits should be the only ones
that change per-HW. The API bits should remain constant across different
HWs.
Currently this is not the case with multi-source LAR (API bit 9). Assign
a new capability bit to eventually replace the API bit. Until the API bit
can be deprecated, the driver will check either to enable multi-source
LAR.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If, on a GO, the CSA time event fails to be scheduled, continue the
flow towards mac80211's state machine so it doesn't get stuck, but
report an error later on the post switch which will cause mac80211
to tear down the operation. This ensures nothing gets stuck due to
the scheduling failure.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The return value in iwl_mvm_get_wakeup_status() is a bit unclear in
that it's not obvious that we don't leak fw_status in some cases.
Use fw_status directly with ERR_PTR() and return only it, that way
the compiler has a chance of proving that it's uninitialized (if it
ever is due to new changes.)

Additionally, this removes a smatch warning since smatch couldn't
figure out that fw_status can't, in fact, leak here.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When IWLWIFI_DEBUGFS is not set, we should not unlock the mutex after
calling iwl_mvm_query_wakeup_reasons(), because this function unlocks
it already.  Move the goto out_iterate outside the #ifdef.

Change-Id: I13d86402aecf0eeec44b1abbe2b244fbc706a5eb
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

The code here is a little confusing, the iwl_mvm_te_check_disconnect()
will check that the interface is a station, but going into it after
already having processed the time even end for P2P seems strange at
first look.

Put a switch statement there to distinguish the interface types and
make this more readable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We previously enabled the smart FIFO (SF) in BSS only after
association.
This cause interrupt latency on P2P on certain devices.
Change the working model to enable the SF all the time and
play with the timeout values based on the association state.
This change was not tested on older firwmares, so make it
happen only on -13.ucode and up.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

More sub system IDs were introduced for the 8260 series.
Add the new sub system IDs so the cards can be recognized.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware was not using the new API, so we don't need to
differentiate between the different stages of this new API.
The main difference here is that most of the hard coded
values are not sent through the command anymore.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The newer devices will enable a new register for this
(DEVICE_SET_NMI_8000B_REG), but the interrupt handler
isn't wired yet.
Keep the old register for now.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When a station goes to sleep, we can't transmit any frame
to it. This means that until that station will wake up, a
queue that is dedicated to this station won't progress at
all. Take this into account when monitoring stuck queues
and don't account for the time the station was asleep.
This allows to mask false positives where the queues are
stuck not because of a bug, but because of the station
being asleep.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows the op_mode to let the transport know that a
queue is currently frozen and that its timer should be
stopped.
When the queue is unfrozen, its timer should be set to
expire after the remainder of the timeout has elapsed.
This can be used when stations go to sleep. When a station
goes to sleep, the op_mode can freeze the timer so that the
queue will never be considered as stuck. When the station
wakes up, the queue will be unfrozen.
This is meant to avoid false positives that would happen if
a buggy station goes to sleep for a very long time. In case
we have a dedicated queue for this station (BA agreement)
and it goes to sleep for a very long time, the queue would
rightfully be stopped during all that time. In this case,
the stuck queue timer could fire and that would be a false
positive.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The Tx statistics weren't updated when using fixed rate for
debugging. Fix this as Tx statistics are useful in this use case.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

RTNL is not taken during CT-kill so regulatory APIs cannot be invoked.
That's fine, since the HW is only brought up to check the temperature
during CT-kill. We don't expect Tx or scanning.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When using IBSS, it's easily possible to exhaust the number
of available stations in the driver, so don't warn on it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we load the firmware for the 8000 B step device, it'll
verify its signature. In the current version of the
hardware, there can be a race between the WiFi firmware
being loaded and the Bluetooth firmware being loaded.

Check that WiFi is authenticated, if not, take ownership
on the authentication machine to make sure that the WiFi
firmware will be authenticated.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New sub system IDs were introduced for the 8260 series.
This patch adds them so new 8260 cards can be recognized.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Make the print a bit more readable.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the FW returns an invalid channels count in response to an MCC request,
make sure we don't reference invalid indices in the channels array.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>