On some Cherry Trail systems the GPU ACPI fwnode has power-resources which
point to the PMIC, which is connected over a LPSS I2C controller.

We add a device-link to make sure that the I2C controller is resumed before
the GPU is. But the pci-core changes the power-state of PCI devices from
D3 to D0 at noirq time (to restore the PCI config registers) and before
this commit we were bringing up the I2C controllers from a resume_early
handler which runs later. More specifically the pm-core will first run
all resume_noirq handlers in order and then all resume_early handlers.

So we must not only make sure that the handlers are run in the right order,
but also that the resume of the I2C controller is done at noirq time.

The behavior before this commit, resuming the I2C controller from a
resume_early handler leads to the following errors:

 i2c_designware 808622C1:06: controller timed out
 ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
 ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
 video LNXVIDEO:00: Failed to change power state to D0

This commit changes the acpi_lpss.c code to resume the BYT/CHT I2C
controllers at resume_noirq time fixing this.
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

On some Bay Trail systems the GPU ACPI fwnode has power-resources which
point to the PMIC, which is connected over the LPSS I2C5 controller.

This one was quite nasty to debug, unlike on CHT where the same problem
leads to errors like these:

     i2c_designware 808622C1:06: controller timed out
     ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
     ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
     video LNXVIDEO:00: Failed to change power state to D0

On BYT the read-modify-write done by drivers/acpi/pmic/intel_pmic_xpower.c
on the AXP288 PMIC register to change the power-resource state *seems* to
succeed.

But in reality, because the I2C controller has not been resumed yet, the
read silently fails and returns the wrong value, where as the write does
succeed, writing back the wrong value for all the other power-resources
in the same register, turning off a bunch of them. Which of course does
not end well.

This commit adds a RPM consumer link from the GPU (which has a LNXVIDEO
HID) to the BYT LPSS I2C5 controller, so that the I2C controller gets
resumed before the GPU is resumed and thus before we try to change the
power-resource.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

On some Cherry Trail systems the GPU ACPI fwnode has power-resources which
point to the PMIC, which is connected over the LPSS I2C7 controller.

Due to probe ordering currently we resume the GPU and thus try to access
the ACPI power-resources before the I2C controller has been resumed. This
leads to the following errors:

 i2c_designware 808622C1:06: controller timed out
 ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
 ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
 video LNXVIDEO:00: Failed to change power state to D0

This commit adds a RPM consumer link from the GPU (which has a LNXVIDEO
HID) to the CHT LPSS I2C7 controller, so that the I2C controller gets
resumed before the GPU is resumed.
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

On some Cherry Trail systems the GPU ACPI fwnode has power-resources which
point to the PMIC, which is connected over one of the LPSS I2C controllers.

To get the suspend/resume ordering correct for this we need to be able to
add device-links between the GPU and the I2c controller. The GPU is a PCI
device, so this requires acpi_lpss_find_device() to also work on PCI devs.
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Make hid_uid_match helper accept a NULL uid argument, so that we can also
check for matches against devices with are not expected to have a uid such
as the LNXVIDEO device.
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The hid_uid_match() helper is only used to check if a given acpi_device
matches a certain hid + uid combination. Make the first argument the
acpi_device to check to make this more clear.
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

lpss_iosf_enter_d3_state() checks if all hw-blocks using the DMA
controllers are in d3 before powering down the DMA controllers.

But on devices, where the I2C bus connected to the PMIC is shared by
the PUNIT, the controller for that bus will never reach d3 since it has
an effectively empty _PS3 method. Instead it appears to automatically
power-down during S0i3 and we never see it as being in d3.

This causes the DMA controllers to never be powered-down on these devices,
causing them to never reach S0i3. This commit uses the ACPI _SEM method
to detect if an I2C bus is shared with the PUNIT and if it is, it removes
it from the mask of devices which lpss_iosf_enter_d3_state() checks for.

This fixes these devices never reaching any S0ix states.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Bay and Cherry Trail DSTDs represent a different set of devices depending
on which OS the device think it is booting. One set of decices for Windows
and another set of devices for Android which targets the Android-x86 Linux
kernel fork (which e.g. used to have its own display driver instead of
using the i915 driver).

Which set of devices we are actually going to get is out of our control,
this is controlled by the ACPI OSID variable, which gets either set through
an EFI setup option, or sometimes is autodetected. So we need to support
both.

This commit adds support for the 80862286 and 808622C0 ACPI HIDs which we
get for the first resp. second DMA controller on Cherry Trail devices when
OSID is set to Android.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Disable interrupts while configuring the transfer and enable them back.

We have below as the programming sequence
1. start and slave address
2. byte count and stop

In some customer platform there was a lot of interrupts between 1 and 2
and after slave address (around 7 clock cyles) if 2 is not executed
then the transaction is nacked.

To fix this case make the 2 writes atomic.
Signed-off-by: NShubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
[wsa: added a newline for better readability]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Commit fe8e9350 ("irqchip/gic-v3-its: Use full range of LPIs"), removes
the cap for lpi_id_bits, which causes the following warning to trigger on a
QDF2400 server:

 WARNING: CPU: 0 PID: 0 at mm/page_alloc.c:4066  __alloc_pages_nodemask
 ... 
 Call trace:
  __alloc_pages_nodemask+0x2d8/0x1188
  alloc_pages_current+0x8c/0xd8
  its_allocate_prop_table+0x5c/0xb8
  its_init+0x220/0x3c0
  gic_init_bases+0x250/0x380
  gic_acpi_init+0x16c/0x2a4

In its_alloc_lpi_tables(), lpi_id_bits is 24 in QDF2400. The allocation in
allocate_prop_table() tries therefore to allocate 16M (order 12 if
pagesize=4k), which triggers the warning.

As said by MarcL

 Capping lpi_id_bits at 16 (which is what we had before) is plenty,
 will save a some memory, and gives some margin before we need to push
 it up again.

Bring the upper limit of lpi_id_bits back to prevent

Fixes: fe8e9350 ("irqchip/gic-v3-its: Use full range of LPIs")
Suggested-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJia He <jia.he@hxt-semitech.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Tested-by: NOlof Johansson <olof@lixom.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lkml.kernel.org/r/1535432006-2304-1-git-send-email-jia.he@hxt-semitech.com

Platform data pointer may be NULL. We check it everywhere but in one
place. Fix it.

Fixes: 8af70cd2 ("memory: aemif: add support for board files")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: NOlof Johansson <olof@lixom.net>

Firmware can provide zero as values for sustained performance level and
corresponding sustained frequency in kHz in order to hide the actual
frequencies and provide only abstract values. It may endup with divide
by zero scenario resulting in kernel panic.

Let's set the multiplication factor to one if either one or both of them
(sustained_perf_level and sustained_freq) are set to zero.

Fixes: a9e3fbfa ("firmware: arm_scmi: add initial support for performance protocol")
Reported-by: NIonela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

If parent_get class method is not supported by the OSDs, fall back to
the legacy class method and assume that the parent is in the default
(i.e. "") namespace.  The "use the child's image namespace" workaround
is no longer needed because creating images within namespaces will
require parent_get aware OSDs.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Reviewed-by: NJason Dillaman <dillaman@redhat.com>

In preparation for the new parent_get and parent_overlap_get class
methods, factor out the fetching and decoding of parent data.

As a side effect, we now decode all four fields in the "no parent"
case.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Reviewed-by: NJason Dillaman <dillaman@redhat.com>

Commit 12864ff8 (ACPI / LPSS: Avoid PM quirks on suspend and resume
from hibernation) bypasses lpss quirks for S3 and S4, by setting a flag
for S3/S4 in acpi_lpss_suspend(), and check that flag in
acpi_lpss_resume().

But this overlooks the boot case where acpi_lpss_resume() may get called
without a corresponding acpi_lpss_suspend() having been called.

Thus force setting the flag during boot.

Fixes: 12864ff8 (ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200989Reported-and-tested-by: NWilliam Lieurance <william.lieurance@namikoda.com>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+: 12864ff8 (ACPI / LPSS: Avoid ...)
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Calling dmi_check_system() early only works on X86. Other
architectures initialize the DMI subsystem later so it's not
ready yet when ACPI itself gets initialized.

In the best case it results in a useless call to a function which
will do nothing. But depending on the dmi implementation, it could
also result in warnings. Best is to not call the function when it
can't work and isn't needed.

Additionally, if anyone ever needs to add non-x86 quirks, it would
surprisingly not work, so document the limitation to avoid confusion.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Fixes: cce4f632 (ACPI: fix early DSDT dmi check warnings on ia64)
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The raspberrypi-hwmon driver doesn't automatically load, although it does work
when loaded, by adding the alias it auto loads as expected when built as a
module. Tested on RPi2/RPi3 on 32 bit kernel and RPi3B+ on aarch64 with
Fedora 28 and a patched 4.18 RC kernel.

Fixes: 3c493c885cf ("hwmon: Add support for RPi voltage sensor")
Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
CC: Stefan Wahren <stefan.wahren@i2se.com>
CC: Eric Anholt <eric@anholt.net>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NStefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

As part of 226ab561 ("device-dax: Convert to vmf_insert_mixed and
vm_fault_t") in 4.19-rc1, 'rc' was not converted to vm_fault_t.  Now
converted.

Link: http://lkml.kernel.org/r/20180830153813.GA26059@jordon-HP-15-Notebook-PCSigned-off-by: NSouptick Joarder <jrdr.linux@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ross Zwisler <zwisler@kernel.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Within show_valid_zones() the function test_pages_in_a_zone() should be
called for online memory blocks only.

Otherwise it might lead to the VM_BUG_ON due to uninitialized struct
pages (when CONFIG_DEBUG_VM_PGFLAGS kernel option is set):

 page dumped because: VM_BUG_ON_PAGE(PagePoisoned(p))
 ------------[ cut here ]------------
 Call Trace:
 ([<000000000038f91e>] test_pages_in_a_zone+0xe6/0x168)
  [<0000000000923472>] show_valid_zones+0x5a/0x1a8
  [<0000000000900284>] dev_attr_show+0x3c/0x78
  [<000000000046f6f0>] sysfs_kf_seq_show+0xd0/0x150
  [<00000000003ef662>] seq_read+0x212/0x4b8
  [<00000000003bf202>] __vfs_read+0x3a/0x178
  [<00000000003bf3ca>] vfs_read+0x8a/0x148
  [<00000000003bfa3a>] ksys_read+0x62/0xb8
  [<0000000000bc2220>] system_call+0xdc/0x2d8

That VM_BUG_ON was triggered by the page poisoning introduced in
mm/sparse.c with the git commit d0dc12e8 ("mm/memory_hotplug:
optimize memory hotplug").

With the same commit the new 'nid' field has been added to the struct
memory_block in order to store and later on derive the node id for
offline pages (instead of accessing struct page which might be
uninitialized).  But one reference to nid in show_valid_zones() function
has been overlooked.  Fixed with current commit.  Also, nr_pages will
not be used any more after test_pages_in_a_zone() call, do not update
it.

Link: http://lkml.kernel.org/r/20180828090539.41491-1-zaslonko@linux.ibm.com
Fixes: d0dc12e8 ("mm/memory_hotplug: optimize memory hotplug")
Signed-off-by: NMikhail Zaslonko <zaslonko@linux.ibm.com>
Acked-by: NMichal Hocko <mhocko@suse.com>
Reviewed-by: NPavel Tatashin <pavel.tatashin@microsoft.com>
Cc: <stable@vger.kernel.org>	[4.17+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Not all SFPs implement the registers containing sensor limits and
alarms. Luckily, there is a bit indicating if they are implemented or
not. Add checking for this bit, when deciding if the hwmon attributes
should be visible.

Fixes: 1323061a ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct the formula for calculating the RQ page remainder,
which should be in byte granularity.  The result will be
non-zero only for RQs smaller than PAGE_SIZE, as an RQ size
is a power of 2.

Divide this by the SQ stride (MLX5_SEND_WQE_BB) to get the
SQ offset in strides granularity.

Fixes: d7037ad7 ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

syzbot reports a divide-by-zero off the NBD_SET_BLKSIZE ioctl.
We need proper validation of the input here. Not just if it's
zero, but also if the value is a power-of-2 and in a valid
range. Add that.

Cc: stable@vger.kernel.org
Reported-by: Nsyzbot <syzbot+25dbecbec1e62c6b0dd4@syzkaller.appspotmail.com>
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

DNV's iTCO is slightly different with SMBCTRL sitting at a different
offset when compared to all other devices. Let's fix so that we can
properly use iTCO watchdog.

Fixes: 84d7f2eb ("i2c: i801: Add support for Intel DNV")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA.  There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA.  This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.

To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.

Fixes: ec86f14e ("bnxt_en: Add ULP calls to stop and restart IRQs.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unused bnxt_subtract_ulp_resources().  Change
bnxt_get_max_func_irqs() to static since it is only locally used.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the driver detects that resources have changed during open, it
should reset the rx and tx rings to 0.  This will properly setup the
init sequence to initialize the default rings again.  We also need
to signal the RDMA driver to stop and clear its interrupts.  We then
call the RoCE driver to restart if a new set of default rings is
successfully reserved.

Fixes: 25e1acd6 ("bnxt_en: Notify firmware about IF state changes.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__emac_calc_base_mr1 was used instead of __emac4_calc_base_mr1
by copy-paste mistake for emac4syn.

Fixes: 45d6e545 ("net/ibm/emac: add 8192 rx/tx fifo size")
Signed-off-by: NIvan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit afb2c443 ("drm/i915/ddi: Push pipe clock enabling to encoders")
inadvertently stopped enabling the pipe clock for any DP-MST stream
after the first one. It also rearranged the pipe clock enabling wrt.
initial MST payload allocation step (which may or may not be a
problem, but it's contrary to the spec.).

Fix things by making the above commit truly a non-functional change.

Fixes: afb2c443 ("drm/i915/ddi: Push pipe clock enabling to encoders")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107365Reported-by: NLyude Paul <lyude@redhat.com>
Reported-by: dmummenschanz@web.de
Tested-by: dmummenschanz@web.de
Tested-by: NLyude Paul <lyude@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: dmummenschanz@web.de
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180831174739.30387-1-imre.deak@intel.com
(cherry picked from commit 2b5cf4ef541f1b2facaca58cae5e8e0b5f19ad4c)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

This patch fixes the PPS4 and PPS5 register definition macros that were
resulting into an incorect MMIO address.

Fixes: 2efbb2f0 ("i915/dp/dsc: Add DSC PPS register definitions")
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824014807.14681-1-manasi.d.navare@intel.com
(cherry picked from commit 5df52391ddbed869c7d67b00fbb013bd64334115)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

This re-applies the workaround for "some DP sinks, [which] are a
little nuts" from commit 1a36147b ("drm/i915: Perform link
quality check unconditionally during long pulse").
It makes the secondary AOC E2460P monitor connected via DP to an
acer Veriton N4640G usable again.

This hunk was dropped in commit c85d200e ("drm/i915: Move SST
DP link retraining into the ->post_hotplug() hook")

Fixes: c85d200e ("drm/i915: Move SST DP link retraining into the ->post_hotplug() hook")
[Cleaned up commit message, added stable cc]
Signed-off-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NJan-Marek Glogowski <glogow@fbihome.de>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20180825191035.3945-1-lyude@redhat.com
(cherry picked from commit 3cf71bc9904d7ee4a25a822c5dcb54c7804ea388)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

This card identifies itself as:
  Ethernet controller [0200]: NCube Device [10ff:8168] (rev 06)
  Subsystem: TP-LINK Technologies Co., Ltd. Device [7470:3468]

Adding a new entry to rtl8169_pci_tbl makes the card work.

Link: http://launchpad.net/bugs/1788730Signed-off-by: NAnthony Wong <anthony.wong@ubuntu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This trys to give new born vGPU with higher scheduling chance
not only with adding to sched list head and also have higher
priority for workload sched for 2 seconds after starting to
schedule it. In order for fast GPU execution during VM boot,
and ensure guest driver setup with required state given in time.

This fixes recent failure seen on one VM with multiple linux VMs
running on kernel with commit 2621cefa("drm/i915: Provide a timeout to i915_gem_wait_for_idle() on setup"),
which had shorter setup timeout that caused context state init failed.

v2: change to 2s for higher scheduling period

Cc: Yuan Hang <hang.yuan@intel.com>
Reviewed-by: NHang Yuan <hang.yuan@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>

The kernel module may sleep with holding a spinlock.

The function call paths (from bottom to top) in Linux-4.16 are:

[FUNC] usleep_range
drivers/net/ethernet/cadence/macb_main.c, 648:
	usleep_range in macb_halt_tx
drivers/net/ethernet/cadence/macb_main.c, 730:
	macb_halt_tx in macb_tx_error_task
drivers/net/ethernet/cadence/macb_main.c, 721:
	_raw_spin_lock_irqsave in macb_tx_error_task

To fix this bug, usleep_range() is replaced with udelay().

This bug is found by my static analysis tool DSAC.
Signed-off-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mx8dv never entered into production and there is no other place
in the kernel referring to this SoC, so remove it from the
driver's compatible entry.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This driver currently emits a STOP if the next message is not
I2C_MD_RD.  It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.

Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.

Fixes: 6a62974b ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This driver currently emits a STOP if the next message is not
I2C_MD_RD.  It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.

Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.

Fixes: dd6fd4a3 ("i2c: uniphier: add UniPhier FIFO-less I2C driver")
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The cpsw-phy-sel device is not a child of the cpsw interconnect target
module. It lives in the system control module.

Let's fix this issue by trying to use cpsw-phy-sel phandle first if it
exists and if not fall back to current usage of trying to find the
cpsw-phy-sel child. That way the phy sel driver can be a child of the
system control module where it belongs in the device tree.

Without this fix, we cannot have a proper interconnect target module
hierarchy in device tree for things like genpd.

Note that deferred probe is mostly not supported by cpsw and this patch
does not attempt to fix that. In case deferred probe support is needed,
this could be added to cpsw_slave_open() and phy_connect() so they start
handling and returning errors.

For documenting it, looks like the cpsw-phy-sel is used for all cpsw device
tree nodes. It's missing the related binding documentation, so let's also
update the binding documentation accordingly.

Cc: devicetree@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This addresses a v4.19-rc1 regression in the PL111 DRM driver in
drivers/gpu/pl111/*

The driver uses the CMA KMS helpers and will thus at some point call
down to dma_alloc_attrs() to allocate a chunk of contigous DMA memory
for the framebuffer.

It appears that in v4.18, it was OK that this (and other DMA mastering
AMBA devices) left dev->coherent_dma_mask blank (zero).

In v4.19-rc1 the WARN_ON_ONCE(dev && !dev->coherent_dma_mask) in
dma_alloc_attrs() in include/linux/dma-mapping.h is triggered.  The
allocation later fails when get_coherent_dma_mask() is called from
__dma_alloc() and __dma_alloc() returns NULL:

drm-clcd-pl111 dev:20: coherent DMA mask is unset
drm-clcd-pl111 dev:20: [drm:drm_fb_helper_fbdev_setup] *ERROR*
 	       	        Failed to set fbdev configuration

It turns out that in commit 4d8bde88 ("OF: Don't set default
coherent DMA mask") the OF core stops setting the default DMA mask on
new devices, especially those lines of the patch:

- if (!dev->coherent_dma_mask)
-               dev->coherent_dma_mask = DMA_BIT_MASK(32);

Robin Murphy solved a similar problem in a5516219 ("of/platform:
Initialise default DMA masks") by simply assigning dev.coherent_dma_mask
and the dev.dma_mask to point to the same when creating devices from the
device tree, and introducing the same code into the code path creating
AMBA/PrimeCell devices solved my problem, graphics now come up.

The code simply assumes that the device can access all of the system
memory by setting the coherent DMA mask to 0xffffffff when creating a
device from the device tree, which is crude, but seems to be what kernel
v4.18 assumed.

The AMBA PrimeCells do not differ between coherent and streaming DMA so
we can just assign the same to any DMA mask.

Possibly drivers should augment their coherent DMA mask in accordance
with "dma-ranges" from the device tree if more finegranular masking is
needed.
Reported-by: NRussell King <linux@armlinux.org.uk>
Fixes: 4d8bde88 ("OF: Don't set default coherent DMA mask")
Cc: Russell King <linux@armlinux.org.uk>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Instead of forcing a distro or other system builder to choose
at build time whether the CPU is trusted for CRNG seeding via
CONFIG_RANDOM_TRUST_CPU, provide a boot-time parameter for end users to
control the choice. The CONFIG will set the default state instead.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>

Check the return codes of these functions and halt reset
in case of failure. The driver will remain in a dormant state
until the next reset event, when device initialization will be
re-attempted.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>