After all relevant pipes are disabled and after we've updated all the
state with the staged state, but before we call the per-crtc
->mode_set functions there's a very natural point to set up any
shared/global resources like
- shared plls (obviously only the setup, the enabling needs to be
  separately handling with a separate refcount)
- global watermark state like the DSPARB on gmch platforms
- workaround bits that depend upon the exact global output
  configuration
- enabling the right set of refclocks
- enabling/disabling manual power wells.

Now for a lot of these things we can't move them into this function
yet, most often because we only compute the required information in
the per-crtc ->mode_set callback. Which is too late. But due to a
bunch of reasons (check-only atomic modeset, fastboot&hw state checks,
...) we need to separate the computation of that state from the actual
hw frobbery anyway. So we can move things into this new callback step-
by-step.

Others can't be moved here (or implemented at all) because our code
lacks the smarts to properly update them. E.g. the DSPARB can only be
updated when all pipes are disabled, so if we decide to change it's
value, we need to disable _all_ pipes. The infrastructure for that is
already in place (with the various pipe masks that driver the modeset
logic). But again we need to move a few things out of ->mode_set
first before we can even implement the correct decision making.

In any case, we need to start somewhere, so let's start with the
callback: Some small follow-up patches will make immediate good use of
it.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since it is one. We need to move this code to encoder specific callbacks
eventually, to kill all that inversion of control ...
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Atm we have a few funny issues where we enable/disable shared
pll clocks. To make it clear that we are not required to enable/
disable the pch plls together with the other pch resources (and
so should keep it running when it's used by another pipe in
a shared pll configuration) add a comment.

This note is lifted from "Graphics BSpec: vol4g North Display Engine
Registers [IVB], Display Mode Set Sequence", step 9.d. of the enable
sequence:

"Configure and enable PCH DPLL, wait for PCH DPLL warmup (Can be
done anytime before enabling PCH transcoder)."

Since fixing the pll sharing code to no longer disable shared plls
if they're still in use is more involved, let's just stick with the
comment for now.

v2: Make the comment in the code clearer, to address questions raised
by Paulo Zanoni in review.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

My machine here has the correct ones already, but better safe
than sorry. IBX has different settings for that register, and
on IBX the device defaults match the recommended values. Hence
I did not add the respective writes for IBX.

LPT needs the same settings, but that has been done already

commit 4acf5186
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date:   Wed Jul 4 20:15:16 2012 -0300

    drm/i915: program FDI_RX TP and FDI delays

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For reference, see "Graphics BSpec: vol4g North Display Engine
Registers [IVB], Display Mode Set Sequence", step 4 of the enabling
sequence:

a. "Enable PCH FDI Receiver PLL, wait for warmup plus DMI latency
b. "Switch from Rawclk to PCDclk in FDI Receiver
c. "Enable CPU FDI Transmitter PLL, wait for warmup"

Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to "Graphics BSpec: vol4g North Display Engine Registers [IVB],
Display Mode Set Sequence" We need to write the TU size register
of the fdi RX unit _before_ starting to train the link.

Note: The current code is actually correct as Paulo mentioned in
review, but it's a bit confusion since only the fdi rx/tx plls need to
be enabled before the cpu pipes/planes. Hence it's still a good idea
to move the TU_SIZE setting to the "right" spot in the sequence, to
better match Bspec.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The debug message is only relevant on CPT/PPT PCH ports, so move
it into the correct if clause.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Daniel's backmerge

commit c2fb7916
Merge: 29de6ce5 6f0c0580
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Mon Oct 22 14:34:51 2012 +0200

    Merge tag 'v3.7-rc2' into drm-intel-next-queued

to solve conflicts blew up (either git or Daniel was trying to be too
clever for their own good; it's usually convenient to blame tools ;) and
caused the changes of

commit 0c96c65b
Author: Jani Nikula <jani.nikula@intel.com>
Date:   Wed Sep 26 18:43:10 2012 +0300

    drm/i915: use adjusted_mode instead of mode for checking the 6bpc force flag

in ironlake_crtc_mode_set() to be dropped.

Fix the call in ironlake_crtc_mode_set() again, and while at it, also fix
the new, copy-pasted haswell_crtc_mode_set() to use adjusted_mode.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NYuly Novikov <ynovikov@chromium.org>
[Jani: ripped this change separate from the scaling mode change support]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

LVDS allowed changing panel fitting scaling mode, while eDP didn't. Copied
relevant code from LVDS to eDP.
Signed-off-by: NYuly Novikov <ynovikov@chromium.org>
[Jani: use fitting mode in intel_panel, remove default mode change]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Prepare for supporting scaling mode configuration also in eDP.

Includes a drive-by-removal of an outdated comment about fitting mode.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

At some point the DPCD size was increased, but the debug print not. While
at it, switch to using hex dump.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just like HSW, VLV does not have a sprite scale. Set
intel_plane->can_scale accordingly.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

SDVOB may be multiplexed with HDMIB. If it's not SDVOB, the same i2c
adapter may be used for HDMIB, with the adjusted config (i.e. with GPIO
bit-banging instead of gmbus). Restore i2c adapter config before error
return from intel_sdvo_init(), letting HDMIB enjoy the joys of gmbus.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

commit 63abf3ed
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Wed Dec 8 16:48:21 2010 +0000

    drm/i915/sdvo: Only use the SDVO pin if it is in the valid range

added a default fallback if BIOS provides an invalid pin mapping, but
failed to force GPIO bit-banging on it. Finish the job, and also clean up
the function a bit. With bit-banging, setting the gmbus speed has no
effect, so drop it.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
[danvet: Extend comment about gmbus in the code a bit.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that all the eDP enablement bits are there, we can actually try to
use the eDP.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's an important step :)
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The cdclk frequency is not always the same, so the value here should
be adjusted to match it.

Version 2: call intel_ddi_get_cdclk_freq instead of reading
CDCLK_FREQ, because the register is just for earlier HW steppings.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

See the documentation for the DDI_FUNC_CTL register, EDP Input Select
bits: when the EDP input selection is B, the VTOTAL_B must be
programmed with the VTOTAL_EDP value, same thing for selection C.

V2: Use I915_READ as suggested by Daniel Vetter.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Same thing as the previous commits. Not renaming this one since it
exists since way before Haswell.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Same as the other registers. This one also appeared on Haswell for the
first time, so that's why we are renaming it.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because the PIPECONF register is actually part of the CPU transcoder,
not the CPU pipe.

Ideally we would also rename PIPECONF to TRANSCONF to remind people
that they should use the transcoder instead of the pipe, but let's
keep it like this for now since most Gens still name it PIPECONF.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to check if any of the pipes is using TRANSCODER_EDP.

V2: DDI_BUF_CTL was renamed, so fix the usage here.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because there's one instance of the register per CPU transcoder and
not per CPU pipe. This is another register that appeared for the first
time on Haswell, and even though its Haswell name is
PIPE_DDI_FUNC_CTL, it will be renamed to TRANS_DDI_FUNC_CTL, so let's
just use the new naming scheme before it confuses more people.

Notice that there's a big improvement on intel_ddi_get_hw_state due to
the new TRANSCODER_EDP.

V2: Also rename the register to TRANS_DDI_FUNC_CTL as suggested by
Damien Lespiau.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This register appeared in Haswell. It does not have an EDP version
because the EDP transcoder is always tied to the DDIA clock. Notice
that if we call PIPE_CLK_SEL(pipe) when pipe is PIPE_A and transcoder
is TRANSCODER_EDP we might introduce a bug, that's why this is a
transcoder register even though it does not have an EDP version.

Even though Haswell names this register PIPE_CLK_SEL, it will be
renamed to TRANS_CLK_SEL in the future, so let's just start using the
real name that makes more sense and avoids misusage.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Before Haswell we used to have the CPU pipes and the PCH transcoders.
We had the same amount of pipes and transcoders, and there was a 1:1
mapping between them. After Haswell what we used to call CPU pipe was
split into CPU pipe and CPU transcoder. So now we have 3 CPU pipes (A,
B and C), 4 CPU transcoders (A, B, C and EDP) and 1 PCH transcoder
(only used for VGA).

For all the outputs except for EDP we have an 1:1 mapping on the CPU
pipes and CPU transcoders, so if you're using CPU pipe A you have to
use CPU transcoder A. When have an eDP output you have to use
transcoder EDP and you can attach this CPU transcoder to any of the 3
CPU pipes. When using VGA you need to select a pair of matching CPU
pipes/transcoders (A/A, B/B, C/C) and you also need to enable/use the
PCH transcoder.

For now we're just creating the cpu_transcoder definitions and setting
cpu_transcoder to TRANSCODER_EDP on DDI eDP code, but none of the
registers was ported to use transcoder instead of pipe. The goal is to
keep the code backwards-compatible since on all cases except when
using eDP we must have pipe == cpu_transcoder.

V2: Comment the haswell_crtc_off chunk, suggested by Damien Lespiau
and Daniel Vetter.

We currently need the haswell_crtc_off chunk because TRANSCODER_EDP
can be used by any CRTC, so when you stop using it you have to stop
saying you're using it, otherwise you may have at some point 2 CRTCs
claiming they're using TRANSCODER_EDP (a disabled CRTC and an enabled
one), then the HW state readout code will get completely confused.

In other words:

Imagine the following case:
  xrandr --output eDP1 --auto --crtc 0
  xrandr --output eDP1 --off
  xrandr --output eDP1 --auto --crtc 2

After the last command you could get a "pipe A assertion failure
(expected off, current on)" because CRTC 0 still claims it's using
TRANSCODER_EDP, so the HW state readout function will read it
(through PIPECONF) and expect it to be off, when it's actually on
because it's being used by CRTC 2.

So when we make "intel_crtc->cpu_transcoder = intel_crtc->pipe" we
make sure we're pointing to our own original CRTC which is certainly
not used by any other CRTC.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On Ironlake we have one PCH transcoder and FDI per pipe, so we know
that if ironlake_crtc_driving_pch returns false we can disable the PCH
transcoder and we also know that when we disable the crtc we can also
disable the PCH transcoder.

On Haswell there is only 1 PCH transcoder and FDI and they can be used
by any CRTC. So if for one specific crtc haswell_crtc_driving_pch
returns false we can't assert anything about the state of the PCH
transcoder or the FDI link without checking if any other CRTC is using
the PCH.

So on this commit remove the "assert_fdi_{t,r}x_disabled" form
haswell_crtc_enable and also only disable FDI and the PCH transcoder
if the port being disabled was actually a PCH port (we only have one
port using PCH: the VGA port).
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By forking Ironlake and Haswell functions. The only callers are
{ironlake,haswell}_crtc_enable anyway, and this way we won't need to
add other checks on the Haswell version for the next gens.

V2: Even simpler, as pointed by Jani Nikula.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These functions were forked from their Ironlake versions, so now fix
the gen checks to reflect the fact that they will only run on Haswell.

It is worth noticing that we are not considering IBX/CPT possible on
Haswell anymore. So far on Haswell enablement we kept trying to still
consider IBX/CPT as a possibility with a Haswell CPU, but this was
never tested, I really doubt it will work with the current code and we
don't really have plans to support it. Future patches will remove the
IBX/CPT code from other Haswell functions. Notice that we still have a
WARN on haswell_crtc_mode_set in case we detect non-LPT PCH.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The last commit forked a Haswell version, so now we remove Haswell
code from these functions.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The way we enable and disable the PCH on Haswell changed considerably
since now we have only one PCH transcoder, so we can't keep the same
asserts and we also can't just unconditionally disable the PCH
transcoder for non-PCH outputs. So let's fork a Haswell version.

These new functions look exactly the same as the ironlake versions.
The next patches will introduce the differences.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Identical #define is now available in include/drm/drm_dp_helper.h, nuke the
dupe.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

That thing has grown way too big already.

Also move around a comment to the right spot.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise dp aux won't work on some hsw platforms, since they use a
different rawclk than the 125MHz clock used thus far.

To absolutely not change anything, round up: That way we get the old
63 divider for the default 125MHz clock.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need this when the bios forgets even to set that bit up. Most seem
to do that, even when they don't set up anything else in the panel
power sequencer.

Note that on IBX the rawclk is variable according to Bspec, but
everyone is using 125MHz. The rawclk is fixed to 125MHz on CPT, but
luckily we still have the same register available. On hsw, different
variants have different clocks, hence we need to check the register.

Since other pieces are driven by the rawclock, too, keep the little
helper in a central place.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Like we already do for the LVDS panels. This seems to help greatly
in setting up the backlight, since the BIOS might refuse to cooperate.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>

v2: Move the backlight_off call from panel_off to edp_backlight_off,
noticed by Paulo Zanoni.
Reviewed-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

3 changes:
- If a given value is unset, use the maximal limits from the eDP spec.
- Write back the new values, since otherwise the panel power sequencing
  hw will not dtrt.
- Revert the early bail-out in case the register values are unset.

The last change reverts

commit bfa3384a
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Tue Apr 10 11:58:04 2012 -0700

    drm/i915: check PPS regs for sanity when using eDP

v2:
- Unlock the PP regs as the very first thing. This is a required w/a
  for cpu eDP on port A, and generally a good idea.
- Fixup the panel power control port selection bits.

v3: Paulo Zanoni noticed that I've fumbled the computation of the spec
limit values. Fix them up. We've also noticed that the t8/t9 values in
the vbt/bios-programmed pp are much larger than any limits. My guess
is that this is to conceal any backlight enable/disable delays. So by
using the much shorter limits from the spec, which only concerns the
sink, we risk that we might display before the backlight is fully on,
or disable the output while the backlight still has afterglow. I've
figured I don't care too much, since this will only happen when both
the pp regs are not programmed, and the vbt tables don't contain
anything useful.

v4: Don't set the port selection bits on hsw/LPT, they don't exist any
more.

v5: Fixup spelling issues in comments, as noticed by Jesse Barnes.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>