The corresponding iwl_mac_remove_interface only
acquires the mutex, leading me to believe that
the spinlock is not necessary. However, this
doesn't actually acquire the mutex around the
vif pointer check and assignment, fix that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Adding "bt_coex_active" module parameter for iwlcore to enable/disable
BT coexist; if bt_coex_active is true (default), uCode will do kill/defer
every time the priority line is asserted (BT is sending signals on the
priority line in the PCIx). By disable the bt_coex_active, uCode will
ignore the BT activity and perform the normal operation.

Users might experience transmit issue on some platform due to this
WiFi/BT co-exist problem. The possible symptoms are: NetworkManager and
other similar programs can scan and find all the available APs, but will
timeout and unable to associate with any of the APs; no out-going frames
can be found with wireless sniffer tools.

On those platforms, WiFi communication can be restored by set "bt_coex_active"
module parameter to "false"
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Give better bit filed define and description for flag parameter
in REPLY_BT_CONFIG command:

flags:
 bit 0 - 1: BT channel announcement enabled
         0: disable
 bit 1 - 1: priority of BT device enabled
         0: disable
 bit 2 - 1: BT 2 wire support enabled
         0: disable
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding "radio reset" function to help reset and stabilize the radio.

During normal operation, sometime for unknown reason, radio encounter
problem and can not recover by itself; the best way to
recover from it is to reset and re-tune the radio. Currently, there is
no RF reset command available, but since radio will get reset when
switching channel, use internal hw scan request to force radio
reset and get back to normal operation state.

The internal hw scan will only perform passive scan on the first
available channel (not the channel being used) in associated state. The
request should be ignored if already performing scan operation or STA is
not in associated state.

Also include an "internal_scan" debugfs file to help trigger the
internal scan from user mode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Flowhandler handle the communication between driver and uCode, when any
uCode error happen, we also like to know what is the status of the
flowhandler; it can help to debug flowhandler related problem.

Also adding debugfs file to dump current value of flowhandler registers.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a w/a for a hardware bug. the h/w bug may cause the Rx bit
(bit 15 before shifting it to 31) to clear when using interrupt coalescing.

This does not mean frames are lost - their processing is just delayed until
next interrupt arrives.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For interrupt coalescing timer, the CSR_INT_COALESCING is an 8 bit
register in 32-usec unit, the range can go from 0x00 - 0xFF. set the
range and default timeout value for both calibration mode and operation mode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On beacon change update notification from mac we are not disabling
the tx in adhoc mode. Mac sends BSS_CHANGED_BEACON_ENABLED when
station leaves IBSS. Driver should indicate uCode to not to send
anything on receiving this notification.

Functionality to indicate uCode is duplicated across
two notifications so created a common function called iwl_set_no_assoc.

Fix the issue at
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2133.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Tested-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:

@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of hard-coding the SM PS mode per hardware,
this makes iwlwifi support the new mac80211 API for
controlling the SM PS mode.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This feature enables the on-screen uCode event log dump. The original
method will append the event log to syslog; with this capability,
we also enable the user to write script to capture the
events which provide additional flexibility to help uCode debugging

Method
1) change to debugfs directory (sys/kernel/debug/phyX/iwlagn/data)
2) #cat log_event
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When uCode HW/SW error detected, dumping important CSR (Control and Status
Registers) values.
Also add "csr" debugfs file to dump the current values of CSR defined in
CSR table to syslog.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To help iwlagn uCode debugging, event log will dump to syslog when driver
detect uCode error occurred, but this only happen when compile with
CONFIG_IWLWIFI_DEBUG and debug flag is enabled; which is not always
the case. Also, there is another problem, if the flag is set, the entire
event log buffer will be dump to syslog, it can flood the syslog and
make it very difficult to debug the problem.

Change the default to only dump last 20 entries of event log to syslog
unless the following condition meets:
1. both compile with CONFIG_IWLWIFI_DEBUG and debug flag
is enabled, and then dump the entire event buffer to syslog.
2. dump event log request from debugfs
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we get a state change of associated or not, we need to tell the
ucode via the RX_ON command using the filter flags.  This will prevent
the ucode from sending any packets when not associated, specifically not
sending NULL QOS packets after a deauthentication which causes the AP to
repeatedly send deauth's in some situations.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

uCode error log contain information as to what the error was and where
it occurred necessary to debug any uCode issues.

Always log the information without special debug flag, this can help to
capture the important information when error happened.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

LED blink rate is based on the traffic load, when tx/rx traffic counts
got reset, we also need to reset the led_tpt to prevent incorrect
blink rate being calculated.

Merge both clear_tx_statistics() and clear_rx_statistics() into
single clear_traffic_statistics() function, when reset the traffic byte
counts, both tx and rx need to be reset at the same time, to make
sure calculated the correct led blink rate.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Setting "Spatial multiplexing Power Save" as part of
per device configuration parameter.

Report to uCode based on priv->conf setting, so driver can
have more control of how different devices should operate
in power save mode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

LED blinking rate is based on tx/rx traffic, the most reasonable place
to do it is after update the traffic byte counts

This fixes the recent LED blinking breakage on 3945 introduced by "iwlwifi:
separate led function from statistic notification"
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CSR_INT_COALESCING previously had only one, but now has two single-byte fields.
With only one single-byte field (lowest order byte) it was okay to write via
iwl_write32(), but now with two, an iwl_write32() to the lower order field
clobbers the other field (odd-address CSR_INT_PERIODIC_REG, offset 0x5), and an
iwl_write32() to CSR_INT_PERIODIC_REG could clobber the lowest byte of the
next-higher register (CSR_INT, offset 0x8).

Fortunately, no bad side effects have been produced by the iwl_write32()
usage, due to order of execution (low order byte was always written before
higher order byte), and the fact that writing "0" to the low byte of the
next higher register has no effect (only action is when writing "1"s).

Nonetheless, this cleans up the accesses so no bad side effects might occur
in the future, if execution order changes, or more bit fields get added to
CSR_INT_COALESCING.

Add some comments regarding periodic interrupt usage.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Handle BSS_CHANGED_BEACON_ENABLED to enable the sending
of beacons. Also set the correct HT RXON and QoS config.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When sending beacon commands to the uCode, we must
inform it of the offset in the beacon frame of the
TIM Element so it can transmit packets from the
correct queue. This functionality is implemented
in iwl_set_beacon_tim().

Fix a bug setting the rate_n_flags for the beacon
packet. First, it should not use the station table's
rate (it's a management frame), and second it needs
to properly configure the TX antennas.

Finally, also, clean up and comment relevant functions.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When issue REPLY_STATISTICS_CMD to uCode, two possible flag
can be set in the configuration flags

bit 0: Clear statistics
       0: Do not clear Statistics counters
       1: Clear to zero Statistics counters

Allow "clear" parameter to be set from the caller.

Add debugfs file to clear the statistics counters to help monitor and
debug the uCode behavior.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not use AP's SM_PS setting for our own SM_PS setting.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Different channel has different configuration, need to pass correct
configuration to uCode when send "channel switch" command to uCode.
Invalid configuration will cause sysassert in uCode and produce
un-expected result.

Even it is a very small windows, but we also need to consider and handle
the case if commit_rxon occurred before the "channel switch
announcement" notification received from uCode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To help debug rx related issues, if IWL_DEBUG_RADIO flag is set, print
the rxon configuration when rxon host command send to uCode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since we have a TODO item to make all station
management dependent on virtual interfaces, I
figured I'd start with pushing such a change
to drivers before more drivers start using the
ieee80211_find_sta() API with a hw pointer and
cause us grief later on.

For now continue exporting the old API in form
of ieee80211_find_sta_by_hw(), but discourage
its use strongly.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For 6x50 series, it is wimax/wifi combo device, so driver need to enable
the wimax/wifi co-exist function and send the coexist event priority
table to uCode for operation.

The priority table will be used by uCode to determine what is the proper
action it should take when co-exist with WiMAX.
For example, when WiFi runs a scan, it must own radio exclusively, therefore
will disconnect WiMAX if WiMAX is connected.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Spatial Multiplexing Power Save was disabled to achieve better
throughput while in power save mode by activating all the rx chains all the time.
By doing so, the device power consumption is high.

Enable static/dynamic spatial multiplexing power save if device support
it, which can lower the power consumption without impact throughput.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since iwlagn is the only user of these functions, move it to this module.
This results in a bit more code moving than just these functions since the
functions only used by them are also moved and we need to export the
symbols previously available to them directly.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Invoke workaround to avoid instability in L0->L0S->L1 transition on PCIe bus.
Workaround disables L0S state so device moves directly from L0->L1.
Workaround needed on all devices since and including 4965; add to 6000/1000.

Describe bug and workaround better in comments.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since priv->reg_lock was added to keep multi-access register manipulation
atomic, priv->lock protection is no longer needed.  Remove this from
iwl_apm_stop_master() and iwl_apm_stop().

Add warning of timeout when polling for busmaster disablement confirmation,
and some comments.

NOTE:  This is needed to enable use of apm_ops.stop() within iwl_eeprom_init();
priv->lock does not get initialized until after this flow.  See patch
"remove power-wasting calls to apm_ops.init()"
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Support "channel switch" request by issue "channel switch" host command
to uCode.

There is no separated "channel switch" indication from mac80211,
when detected "IEEE80211_CONF_CHANGE_CHANNEL" flag in iwl_mac_config(),
if the station is in "associated" state, then assume "channel switch
announcement" IE was received by mac80211.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using device configuration structure to decide how to configure
ct_kill host command.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding parameter ranges for bt co-exist configuration command.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Consolidate most iwlXXXX_apm_init() functions into single iwl_apm_init().
Keep iwl3945_apm_init(), but leverage iwl_apm_init() for most functionality.
Update 4965 init sequence to follow most recent factory recommendations.

Add following members to struct iwl_cfg to guide the init sequence:
pll_cfg_val (replaces needs_pll_cfg), set_l0s, use_bsm

Move L0S enable/disable from nic_config() functions to iwl_apm_init().
This satisifies the "FIXME: put here L1A -L0S w/a" notice, and complies
with factory-recommended sequence.

Add debug info message in iwl_apm_init(), and symmetrical message
in iwl_apm_stop().
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This function is only used in iwlagn so there is no need to have it in
iwlcore.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This switches the iwlwifi driver to use paged skb from linear skb for Rx
buffer. So that it relieves some Rx buffer allocation pressure for the
memory subsystem. Currently iwlwifi (4K for 3945) requests 8K bytes for
Rx buffer. Due to the trailing skb_shared_info in the skb->data,
alloc_skb() will do the next order allocation, which is 16K bytes. This
is suboptimal and more likely to fail when the system is under memory
usage pressure. Switching to paged Rx skb lets us allocate the RXB
directly by alloc_pages(), so that only order 1 allocation is required.

It also adjusts the area spin_lock (with IRQ disabled) protected in the
tasklet because tasklet guarentees to run only on one CPU and the new
unprotected code can be preempted by the IRQ handler. This saves us from
spawning another workqueue to make skb_linearize/__pskb_pull_tail happy
(which cannot be called in hard irq context).

Finally, mac80211 doesn't support paged Rx yet. So we linearize the skb
for all the management frames and software decryption or defragmentation
required data frames before handed to mac80211. For all the other frames,
we __pskb_pull_tail 64 bytes in the linear area of the skb for mac80211
to handle them properly.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the ununsed variable data_retry_limit
from priv.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

3945 and 4965 share the functionality for setting RTS and CTS to
the tx_cmd. Unify these functions and move the common
functionality to core.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>