- 07 9月, 2018 3 次提交
-
-
由 Jesper Dangaard Brouer 提交于
The compiler does an efficient job of inlining static C functions. Perf top clearly shows that almost everything gets inlined into the function call xdp_do_redirect. The function xdp_do_redirect end-up containing and interleaving the map and non-map redirect code. This is sub-optimal, as it would be strange for an XDP program to use both types of redirect in the same program. The two use-cases are separate, and interleaving the code just cause more instruction-cache pressure. I would like to stress (again) that the non-map variant bpf_redirect is very slow compared to the bpf_redirect_map variant, approx half the speed. Measured with driver i40e the difference is: - map redirect: 13,250,350 pps - non-map redirect: 7,491,425 pps For this reason, the function name of the non-map variant of redirect have been called xdp_do_redirect_slow. This hopefully gives a hint when using perf, that this is not the optimal XDP redirect operating mode. Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Jesper Dangaard Brouer 提交于
The compiler chooses to not-inline the function __xdp_map_lookup_elem, because it can see that it is used by both Generic-XDP and native-XDP do redirect calls (xdp_do_generic_redirect_map and xdp_do_redirect_map). The compiler cannot know that this is a bad choice, as it cannot know that a net device cannot run both XDP modes (Generic or Native) at the same time. Thus, mark this function inline, even-though we normally leave this up-to the compiler. Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Jesper Dangaard Brouer 提交于
Notice the compiler generated ASM code layout was suboptimal. It assumed map enqueue errors as the likely case, which is shouldn't. It assumed that xdp_do_flush_map() was a likely case, due to maps changing between packets, which should be very unlikely. Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
- 06 9月, 2018 2 次提交
-
-
由 Dmitry Safonov 提交于
As Linus noted, the test for 0 is needless, groups type can follow the usual kernel style and 8*sizeof(unsigned long) is BITS_PER_LONG: > The code [..] isn't technically incorrect... > But it is stupid. > Why stupid? Because the test for 0 is pointless. > > Just doing > if (nlk->ngroups < 8*sizeof(groups)) > groups &= (1UL << nlk->ngroups) - 1; > > would have been fine and more understandable, since the "mask by shift > count" already does the right thing for a ngroups value of 0. Now that > test for zero makes me go "what's special about zero?". It turns out > that the answer to that is "nothing". [..] > The type of "groups" is kind of silly too. > > Yeah, "long unsigned int" isn't _technically_ wrong. But we normally > call that type "unsigned long". Cleanup my piece of pointlessness. Cc: "David S. Miller" <davem@davemloft.net> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: netdev@vger.kernel.org Fairly-blamed-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NDmitry Safonov <dima@arista.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vincent Whitchurch 提交于
Currently, the only way to ignore outgoing packets on a packet socket is via the BPF filter. With MSG_ZEROCOPY, packets that are looped into AF_PACKET are copied in dev_queue_xmit_nit(), and this copy happens even if the filter run from packet_rcv() would reject them. So the presence of a packet socket on the interface takes away the benefits of MSG_ZEROCOPY, even if the packet socket is not interested in outgoing packets. (Even when MSG_ZEROCOPY is not used, the skb is unnecessarily cloned, but the cost for that is much lower.) Add a socket option to allow AF_PACKET sockets to ignore outgoing packets to solve this. Note that the *BSDs already have something similar: BIOCSSEESENT/BIOCSDIRECTION and BIOCSDIRFILT. The first intended user is lldpd. Signed-off-by: NVincent Whitchurch <vincent.whitchurch@axis.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 9月, 2018 23 次提交
-
-
由 Stanislaw Gruszka 提交于
Add validation check for wmm rule when copy rules from fwdb and print error when rule is invalid. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Gustavo A. R. Silva 提交于
Both old and new cannot be NULL at the same time, hence checking new when old is not NULL is unnecessary. Also, notice that new is being dereferenced before it is checked: idx = new->conf.keyidx; The above triggers a static code analysis warning. Address this by removing the NULL check on new and adding a code comment based on the following piece of code: 387 /* caller must provide at least one old/new */ 388 if (WARN_ON(!new && !old)) 389 return 0; Addresses-Coverity-ID: 1473176 ("Dereference before null check") Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Sara Sharon 提交于
Some hardwares have limitations on the packets' type in AMSDU. Add an optional driver callback to determine if two skbs can be used in the same AMSDU or not. Signed-off-by: NSara Sharon <sara.sharon@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Sara Sharon 提交于
Some drivers may have AMSDU size limitation per TID, due to HW constrains. Add an option to set this limit. Signed-off-by: NSara Sharon <sara.sharon@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Sara Sharon 提交于
We have a TXQ abstraction for non-data packets that need powersave buffering. Since the AP cannot sleep, in case of station we can use this TXQ for all management frames, regardless if they are bufferable. Add HW flag to allow that. Signed-off-by: NSara Sharon <sara.sharon@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Shaul Triebitz 提交于
Align to new 11ax draft D3.0. Change/add new MAC and PHY capabilities and update drivers' 11ax capabilities and mac80211's debugfs accordingly. Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Naftali Goldstein 提交于
After masking the he_oper_params, to get the requested values as integers one must rshift and not lshift. Fix that by using the le32_get_bits() macro. Fixes: 41cbb0f5 ("mac80211: add support for HE") Signed-off-by: NNaftali Goldstein <naftali.goldstein@intel.com> [converted to use le32_get_bits()] Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Shaul Triebitz 提交于
For certain sounding frames, it may be useful to report them to userspace even though they don't have a PSDU in order to determine the PHY parameters (e.g. VHT rate/stream config.) Add support for this to mac80211. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Alexander Wetzel 提交于
Rekeying PTK keys without "Extended Key ID for Individually Addressed Frames" did use a procedure not suitable to replace in-use keys and could caused the following issues: 1) Freeze caused by incoming frames: If the local STA installed the key prior to the remote STA we still had the old key active in the hardware when mac80211 switched over to the new key. Therefore there was a window where the card could hand over frames decoded with the old key to mac80211 and bump the new PN (IV) value to an incorrect high number. When it happened the local replay detection silently started to drop all frames sent with the new key. 2) Freeze caused by outgoing frames: If mac80211 was providing the PN (IV) and handed over a clear text frame for encryption to the hardware prior to a key change the driver/card could have processed the queued frame after switching to the new key. This bumped the PN value on the remote STA to an incorrect high number, tricking the remote STA to discard all frames we sent later. 3) Freeze caused by RX aggregation reorder buffer: An aggregation session started with the old key and ending after the switch to the new key also bumped the PN to an incorrect high number, freezing the connection quite similar to 1). 4) Freeze caused by repeating lost frames in an aggregation session: A driver could repeat a lost frame and encrypt it with the new key while in a TX aggregation session without updating the PN for the new key. This also could freeze connections similar to 2). 5) Clear text leak: Removing encryption offload from the card cleared the encryption offload flag only after the card had deleted the key and we did not stop TX during the rekey. The driver/card could therefore get unencrypted frames from mac80211 while no longer be instructed to encrypt them. To prevent those issues the key install logic has been changed: - Mac80211 divers known to be able to rekey PTK0 keys have to set @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0, - mac80211 stops queuing frames depending on the key during the replace - the key is first replaced in the hardware and after that in mac80211 - and mac80211 stops/blocks new aggregation sessions during the rekey. For drivers not setting @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 the user space must avoid PTK rekeys if "Extended Key ID for Individually Addressed Frames" is not being used. Rekeys for mac80211 drivers without this flag will generate a warning and use an extra call to ieee80211_flush_queues() to both highlight and try to prevent the issues with not updated drivers. The core of the fix changes the key install procedure from: - atomic switch over to the new key in mac80211 - remove the old key in the hardware (stops encryption offloading, fall back to software encryption with a potential clear text packet leak in between) - delete the inactive old key in mac80211 - enable hardware encryption offloading for the new key to: - if it's a PTK mark the old key as tainted to drop TX frames with the outgoing key - replace the key in hardware with the new one - atomic switch over to the new (not marked as tainted) key in mac80211 (which also resumes TX) - delete the inactive old key in mac80211 With the new sequence the hardware will be unable to decrypt frames encrypted with the old key prior to switching to the new key in mac80211 and thus prevent PNs from packets decrypted with the old key to be accounted against the new key. For that to work the drivers have to provide a clear boundary. Mac80211 drivers setting @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 confirm to provide it and mac80211 will then be able to correctly rekey in-use PTK keys with those drivers. The mac80211 requirements for drivers to set the flag have been added to the "Hardware crypto acceleration" documentation section. It drills down to: The drivers must not hand over frames decrypted with the old key to mac80211 once the call to set_key() with %DISABLE_KEY has been completed. It's allowed to either drop or continue to use the old key for any outgoing frames which are already in the queues, but it must not send out any of them unencrypted or encrypted with the new key. Even with the new boundary in place aggregation sessions with the reorder buffer are problematic: RX aggregation session started prior and completed after the rekey could still dump frames received with the old key at mac80211 after it switched over to the new key. This is side stepped by stopping all (RX and TX) aggregation sessions when replacing a PTK key and hardware key offloading. Stopping TX aggregation sessions avoids the need to get the PNs (IVs) updated in frames prepared for the old key and (re)transmitted after the switch to the new key. As a bonus it improves the compatibility when the remote STA is not handling rekeys as it should. When using software crypto aggregation sessions are not stopped. Mac80211 won't be able to decode the dangerous frames and discard them without special handling. Signed-off-by: NAlexander Wetzel <alexander@wetzel-home.de> [trim overly long rekey warning] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Shaul Triebitz 提交于
As before with HE, the data needs to be provided by the driver in the skb head, since there's not enough space in the skb CB. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Wen Gong 提交于
Make it possibly for drivers to adjust the default skb_pacing_shift by storing it in the hardware struct. Signed-off-by: NWen Gong <wgong@codeaurora.org> [adjust commit log, move & adjust comment] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
When taking VHT capabilities for a station, copy the new fields if we support them as a transmitter. Also adjust the maximum bandwidth the station supports appropriately. Also, since it was missing, copy tx_highest and rx_highest. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
With newer VHT implementations, it's necessary to look at the HT operation's CCFS2 field to identify the actual bandwidth used. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Depending on whether or not rate control supports selecting rates depending on the bandwidth, we can use VHT extended NSS support. In essence, this is dot11VHTExtendedNSSBWCapable from the spec, since depending on that we'll need to parse the bandwidth. If needed, also set/clear the VHT Capability Element bit for this capability so that we don't advertise it erroneously or don't advertise it when we actually use it. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
IEEE 802.11-2016 extended the VHT capability fields to allow indicating the number of spatial streams depending on the actually used bandwidth, add support for decoding this. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Shaul Triebitz 提交于
In AP mode, If AP advertises HE capabilities, set to true bss_conf::he_supported so that the Driver knows about it. Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Shaul Triebitz 提交于
Same as for HT and VHT. This helps the lower level to know whether the AP supports HE. Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Some drivers may want to also use the TXQ abstraction with non-data packets that need powersave buffering, so add a hardware flag to allow this. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Instead of open-coding the equivalent of le16_encode_bits(), just use that. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
These checks aren't necessary, cfg80211 never passes NULL. Some static checkers complain about the missing checks on the next line, but really the NULL checks are unnecessary. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Ido Yariv 提交于
Export HE capabilities information via debugfs, similar to HT & VHT. Signed-off-by: NIdo Yariv <idox.yariv@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Vlad Buslov 提交于
Recent refactoring of add_metainfo() caused use_all_metadata() to add metainfo to ife action metalist without taking reference to module. This causes warning in module_put called from ife action cleanup function. Implement add_metainfo_and_get_ops() function that returns with reference to module taken if metainfo was added successfully, and call it from use_all_metadata(), instead of calling __add_metainfo() directly. Example warning: [ 646.344393] WARNING: CPU: 1 PID: 2278 at kernel/module.c:1139 module_put+0x1cb/0x230 [ 646.352437] Modules linked in: act_meta_skbtcindex act_meta_mark act_meta_skbprio act_ife ife veth nfsv3 nfs fscache xt_CHECKSUM iptable_mangle ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c tun ebtable_filter ebtables ip6table_filter ip6_tables bridge stp llc mlx5_ib ib_uverbs ib_core intel_rapl sb_edac x86_pkg_temp_thermal mlx5_core coretemp kvm_intel kvm nfsd igb irqbypass crct10dif_pclmul devlink crc32_pclmul mei_me joydev ses crc32c_intel enclosure auth_rpcgss i2c_algo_bit ioatdma ptp mei pps_core ghash_clmulni_intel iTCO_wdt iTCO_vendor_support pcspkr dca ipmi_ssif lpc_ich target_core_mod i2c_i801 ipmi_si ipmi_devintf pcc_cpufreq wmi ipmi_msghandler nfs_acl lockd acpi_pad acpi_power_meter grace sunrpc mpt3sas raid_class scsi_transport_sas [ 646.425631] CPU: 1 PID: 2278 Comm: tc Not tainted 4.19.0-rc1+ #799 [ 646.432187] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017 [ 646.440595] RIP: 0010:module_put+0x1cb/0x230 [ 646.445238] Code: f3 66 94 02 e8 26 ff fa ff 85 c0 74 11 0f b6 1d 51 30 94 02 80 fb 01 77 60 83 e3 01 74 13 65 ff 0d 3a 83 db 73 e9 2b ff ff ff <0f> 0b e9 00 ff ff ff e8 59 01 fb ff 85 c0 75 e4 48 c7 c2 20 62 6b [ 646.464997] RSP: 0018:ffff880354d37068 EFLAGS: 00010286 [ 646.470599] RAX: 0000000000000000 RBX: ffffffffc0a52518 RCX: ffffffff8c2668db [ 646.478118] RDX: 0000000000000003 RSI: dffffc0000000000 RDI: ffffffffc0a52518 [ 646.485641] RBP: ffffffffc0a52180 R08: fffffbfff814a4a4 R09: fffffbfff814a4a3 [ 646.493164] R10: ffffffffc0a5251b R11: fffffbfff814a4a4 R12: 1ffff1006a9a6e0d [ 646.500687] R13: 00000000ffffffff R14: ffff880362bab890 R15: dead000000000100 [ 646.508213] FS: 00007f4164c99800(0000) GS:ffff88036fe40000(0000) knlGS:0000000000000000 [ 646.516961] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 646.523080] CR2: 00007f41638b8420 CR3: 0000000351df0004 CR4: 00000000001606e0 [ 646.530595] Call Trace: [ 646.533408] ? find_symbol_in_section+0x260/0x260 [ 646.538509] tcf_ife_cleanup+0x11b/0x200 [act_ife] [ 646.543695] tcf_action_cleanup+0x29/0xa0 [ 646.548078] __tcf_action_put+0x5a/0xb0 [ 646.552289] ? nla_put+0x65/0xe0 [ 646.555889] __tcf_idr_release+0x48/0x60 [ 646.560187] tcf_generic_walker+0x448/0x6b0 [ 646.564764] ? tcf_action_dump_1+0x450/0x450 [ 646.569411] ? __lock_is_held+0x84/0x110 [ 646.573720] ? tcf_ife_walker+0x10c/0x20f [act_ife] [ 646.578982] tca_action_gd+0x972/0xc40 [ 646.583129] ? tca_get_fill.constprop.17+0x250/0x250 [ 646.588471] ? mark_lock+0xcf/0x980 [ 646.592324] ? check_chain_key+0x140/0x1f0 [ 646.596832] ? debug_show_all_locks+0x240/0x240 [ 646.601839] ? memset+0x1f/0x40 [ 646.605350] ? nla_parse+0xca/0x1a0 [ 646.609217] tc_ctl_action+0x215/0x230 [ 646.613339] ? tcf_action_add+0x220/0x220 [ 646.617748] rtnetlink_rcv_msg+0x56a/0x6d0 [ 646.622227] ? rtnl_fdb_del+0x3f0/0x3f0 [ 646.626466] netlink_rcv_skb+0x18d/0x200 [ 646.630752] ? rtnl_fdb_del+0x3f0/0x3f0 [ 646.634959] ? netlink_ack+0x500/0x500 [ 646.639106] netlink_unicast+0x2d0/0x370 [ 646.643409] ? netlink_attachskb+0x340/0x340 [ 646.648050] ? _copy_from_iter_full+0xe9/0x3e0 [ 646.652870] ? import_iovec+0x11e/0x1c0 [ 646.657083] netlink_sendmsg+0x3b9/0x6a0 [ 646.661388] ? netlink_unicast+0x370/0x370 [ 646.665877] ? netlink_unicast+0x370/0x370 [ 646.670351] sock_sendmsg+0x6b/0x80 [ 646.674212] ___sys_sendmsg+0x4a1/0x520 [ 646.678443] ? copy_msghdr_from_user+0x210/0x210 [ 646.683463] ? lock_downgrade+0x320/0x320 [ 646.687849] ? debug_show_all_locks+0x240/0x240 [ 646.692760] ? do_raw_spin_unlock+0xa2/0x130 [ 646.697418] ? _raw_spin_unlock+0x24/0x30 [ 646.701798] ? __handle_mm_fault+0x1819/0x1c10 [ 646.706619] ? __pmd_alloc+0x320/0x320 [ 646.710738] ? debug_show_all_locks+0x240/0x240 [ 646.715649] ? restore_nameidata+0x7b/0xa0 [ 646.720117] ? check_chain_key+0x140/0x1f0 [ 646.724590] ? check_chain_key+0x140/0x1f0 [ 646.729070] ? __fget_light+0xbc/0xd0 [ 646.733121] ? __sys_sendmsg+0xd7/0x150 [ 646.737329] __sys_sendmsg+0xd7/0x150 [ 646.741359] ? __ia32_sys_shutdown+0x30/0x30 [ 646.746003] ? up_read+0x53/0x90 [ 646.749601] ? __do_page_fault+0x484/0x780 [ 646.754105] ? do_syscall_64+0x1e/0x2c0 [ 646.758320] do_syscall_64+0x72/0x2c0 [ 646.762353] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 646.767776] RIP: 0033:0x7f4163872150 [ 646.771713] Code: 8b 15 3c 7d 2b 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb cd 66 0f 1f 44 00 00 83 3d b9 d5 2b 00 00 75 10 b8 2e 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 be cd 00 00 48 89 04 24 [ 646.791474] RSP: 002b:00007ffdef7d6b58 EFLAGS: 00000246 ORIG_RAX: 000000000000002e [ 646.799721] RAX: ffffffffffffffda RBX: 0000000000000024 RCX: 00007f4163872150 [ 646.807240] RDX: 0000000000000000 RSI: 00007ffdef7d6bd0 RDI: 0000000000000003 [ 646.814760] RBP: 000000005b8b9482 R08: 0000000000000001 R09: 0000000000000000 [ 646.822286] R10: 00000000000005e7 R11: 0000000000000246 R12: 00007ffdef7dad20 [ 646.829807] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000679bc0 [ 646.837360] irq event stamp: 6083 [ 646.841043] hardirqs last enabled at (6081): [<ffffffff8c220a7d>] __call_rcu+0x17d/0x500 [ 646.849882] hardirqs last disabled at (6083): [<ffffffff8c004f06>] trace_hardirqs_off_thunk+0x1a/0x1c [ 646.859775] softirqs last enabled at (5968): [<ffffffff8d4004a1>] __do_softirq+0x4a1/0x6ee [ 646.868784] softirqs last disabled at (6082): [<ffffffffc0a78759>] tcf_ife_cleanup+0x39/0x200 [act_ife] [ 646.878845] ---[ end trace b1b8c12ffe51e657 ]--- Fixes: 5ffe57da ("act_ife: fix a potential deadlock") Signed-off-by: NVlad Buslov <vladbu@mellanox.com> Acked-by: NCong Wang <xiyou.wangcong@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Cong Wang 提交于
Immediately after module_put(), user could delete this module, so e->ops could be already freed before we call e->ops->release(). Fix this by moving module_put() after ops->release(). Fixes: ef6980b6 ("introduce IFE action") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 9月, 2018 7 次提交
-
-
由 Zhenbo Gao 提交于
tipc_conn_queue_evt -> tipc_topsrv_queue_evt tipc_send_work -> tipc_conn_send_work tipc_send_to_sock -> tipc_conn_send_to_sock Signed-off-by: NZhenbo Gao <zhenbo.gao@windriver.com> Reviewed-by: NYing Xue <ying.xue@windriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Zhenbo Gao 提交于
Trivial fix for two spelling mistakes. Signed-off-by: NZhenbo Gao <zhenbo.gao@windriver.com> Reviewed-by: NYing Xue <ying.xue@windriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Xin Long 提交于
When users set params.spp_address and get a trans, ipv6_flowlabel flag should be applied into this trans. But even if this one is not an ipv6 trans, it should not go to apply it into all other transes of the asoc but simply ignore it. Fixes: 0b0dce7a ("sctp: add spp_ipv6_flowlabel and spp_dscp for sctp_paddrparams") Signed-off-by: NXin Long <lucien.xin@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Xin Long 提交于
Now in sctp_apply_peer_addr_params(), if SPP_IPV6_FLOWLABEL flag is set and trans is NULL, it would use trans as the index variable to traverse transport_addr_list, then trans is set as the last transport of it. Later, if SPP_DSCP flag is set, it would enter into the wrong branch as trans is actually an invalid reference. So fix it by using a new index variable to traverse transport_addr_list for both SPP_DSCP and SPP_IPV6_FLOWLABEL flags process. Fixes: 0b0dce7a ("sctp: add spp_ipv6_flowlabel and spp_dscp for sctp_paddrparams") Reported-by: NJulia Lawall <julia.lawall@lip6.fr> Signed-off-by: NXin Long <lucien.xin@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vlad Buslov 提交于
Currently, tcf_action_delete() nulls actions array pointer after putting and deleting it. However, if tcf_idr_delete_index() returns an error, pointer to action is not set to null. That results it being released second time in error handling code of tca_action_gd(). Kasan error: [ 807.367755] ================================================================== [ 807.375844] BUG: KASAN: use-after-free in tc_setup_cb_call+0x14e/0x250 [ 807.382763] Read of size 8 at addr ffff88033e636000 by task tc/2732 [ 807.391289] CPU: 0 PID: 2732 Comm: tc Tainted: G W 4.19.0-rc1+ #799 [ 807.399542] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017 [ 807.407948] Call Trace: [ 807.410763] dump_stack+0x92/0xeb [ 807.414456] print_address_description+0x70/0x360 [ 807.419549] kasan_report+0x14d/0x300 [ 807.423582] ? tc_setup_cb_call+0x14e/0x250 [ 807.428150] tc_setup_cb_call+0x14e/0x250 [ 807.432539] ? nla_put+0x65/0xe0 [ 807.436146] fl_dump+0x394/0x3f0 [cls_flower] [ 807.440890] ? fl_tmplt_dump+0x140/0x140 [cls_flower] [ 807.446327] ? lock_downgrade+0x320/0x320 [ 807.450702] ? lock_acquire+0xe2/0x220 [ 807.454819] ? is_bpf_text_address+0x5/0x140 [ 807.459475] ? memcpy+0x34/0x50 [ 807.462980] ? nla_put+0x65/0xe0 [ 807.466582] tcf_fill_node+0x341/0x430 [ 807.470717] ? tcf_block_put+0xe0/0xe0 [ 807.474859] tcf_node_dump+0xdb/0xf0 [ 807.478821] fl_walk+0x8e/0x170 [cls_flower] [ 807.483474] tcf_chain_dump+0x35a/0x4d0 [ 807.487703] ? tfilter_notify+0x170/0x170 [ 807.492091] ? tcf_fill_node+0x430/0x430 [ 807.496411] tc_dump_tfilter+0x362/0x3f0 [ 807.500712] ? tc_del_tfilter+0x850/0x850 [ 807.505104] ? kasan_unpoison_shadow+0x30/0x40 [ 807.509940] ? __mutex_unlock_slowpath+0xcf/0x410 [ 807.515031] netlink_dump+0x263/0x4f0 [ 807.519077] __netlink_dump_start+0x2a0/0x300 [ 807.523817] ? tc_del_tfilter+0x850/0x850 [ 807.528198] rtnetlink_rcv_msg+0x46a/0x6d0 [ 807.532671] ? rtnl_fdb_del+0x3f0/0x3f0 [ 807.536878] ? tc_del_tfilter+0x850/0x850 [ 807.541280] netlink_rcv_skb+0x18d/0x200 [ 807.545570] ? rtnl_fdb_del+0x3f0/0x3f0 [ 807.549773] ? netlink_ack+0x500/0x500 [ 807.553913] netlink_unicast+0x2d0/0x370 [ 807.558212] ? netlink_attachskb+0x340/0x340 [ 807.562855] ? _copy_from_iter_full+0xe9/0x3e0 [ 807.567677] ? import_iovec+0x11e/0x1c0 [ 807.571890] netlink_sendmsg+0x3b9/0x6a0 [ 807.576192] ? netlink_unicast+0x370/0x370 [ 807.580684] ? netlink_unicast+0x370/0x370 [ 807.585154] sock_sendmsg+0x6b/0x80 [ 807.589015] ___sys_sendmsg+0x4a1/0x520 [ 807.593230] ? copy_msghdr_from_user+0x210/0x210 [ 807.598232] ? do_wp_page+0x174/0x880 [ 807.602276] ? __handle_mm_fault+0x749/0x1c10 [ 807.607021] ? __handle_mm_fault+0x1046/0x1c10 [ 807.611849] ? __pmd_alloc+0x320/0x320 [ 807.615973] ? check_chain_key+0x140/0x1f0 [ 807.620450] ? check_chain_key+0x140/0x1f0 [ 807.624929] ? __fget_light+0xbc/0xd0 [ 807.628970] ? __sys_sendmsg+0xd7/0x150 [ 807.633172] __sys_sendmsg+0xd7/0x150 [ 807.637201] ? __ia32_sys_shutdown+0x30/0x30 [ 807.641846] ? up_read+0x53/0x90 [ 807.645442] ? __do_page_fault+0x484/0x780 [ 807.649949] ? do_syscall_64+0x1e/0x2c0 [ 807.654164] do_syscall_64+0x72/0x2c0 [ 807.658198] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 807.663625] RIP: 0033:0x7f42e9870150 [ 807.667568] Code: 8b 15 3c 7d 2b 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb cd 66 0f 1f 44 00 00 83 3d b9 d5 2b 00 00 75 10 b8 2e 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 be cd 00 00 48 89 04 24 [ 807.687328] RSP: 002b:00007ffdbf595b58 EFLAGS: 00000246 ORIG_RAX: 000000000000002e [ 807.695564] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f42e9870150 [ 807.703083] RDX: 0000000000000000 RSI: 00007ffdbf595b80 RDI: 0000000000000003 [ 807.710605] RBP: 00007ffdbf599d90 R08: 0000000000679bc0 R09: 000000000000000f [ 807.718127] R10: 00000000000005e7 R11: 0000000000000246 R12: 00007ffdbf599d88 [ 807.725651] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 [ 807.735048] Allocated by task 2687: [ 807.738902] kasan_kmalloc+0xa0/0xd0 [ 807.742852] __kmalloc+0x118/0x2d0 [ 807.746615] tcf_idr_create+0x44/0x320 [ 807.750738] tcf_nat_init+0x41e/0x530 [act_nat] [ 807.755638] tcf_action_init_1+0x4e0/0x650 [ 807.760104] tcf_action_init+0x1ce/0x2d0 [ 807.764395] tcf_exts_validate+0x1d8/0x200 [ 807.768861] fl_change+0x55a/0x26b4 [cls_flower] [ 807.773845] tc_new_tfilter+0x748/0xa20 [ 807.778051] rtnetlink_rcv_msg+0x56a/0x6d0 [ 807.782517] netlink_rcv_skb+0x18d/0x200 [ 807.786804] netlink_unicast+0x2d0/0x370 [ 807.791095] netlink_sendmsg+0x3b9/0x6a0 [ 807.795387] sock_sendmsg+0x6b/0x80 [ 807.799240] ___sys_sendmsg+0x4a1/0x520 [ 807.803445] __sys_sendmsg+0xd7/0x150 [ 807.807473] do_syscall_64+0x72/0x2c0 [ 807.811506] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 807.818776] Freed by task 2728: [ 807.822283] __kasan_slab_free+0x122/0x180 [ 807.826752] kfree+0xf4/0x2f0 [ 807.830080] __tcf_action_put+0x5a/0xb0 [ 807.834281] tcf_action_put_many+0x46/0x70 [ 807.838747] tca_action_gd+0x232/0xc40 [ 807.842862] tc_ctl_action+0x215/0x230 [ 807.846977] rtnetlink_rcv_msg+0x56a/0x6d0 [ 807.851444] netlink_rcv_skb+0x18d/0x200 [ 807.855731] netlink_unicast+0x2d0/0x370 [ 807.860021] netlink_sendmsg+0x3b9/0x6a0 [ 807.864312] sock_sendmsg+0x6b/0x80 [ 807.868166] ___sys_sendmsg+0x4a1/0x520 [ 807.872372] __sys_sendmsg+0xd7/0x150 [ 807.876401] do_syscall_64+0x72/0x2c0 [ 807.880431] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 807.887704] The buggy address belongs to the object at ffff88033e636000 which belongs to the cache kmalloc-256 of size 256 [ 807.900909] The buggy address is located 0 bytes inside of 256-byte region [ffff88033e636000, ffff88033e636100) [ 807.913155] The buggy address belongs to the page: [ 807.918322] page:ffffea000cf98d80 count:1 mapcount:0 mapping:ffff88036f80ee00 index:0x0 compound_mapcount: 0 [ 807.928831] flags: 0x5fff8000008100(slab|head) [ 807.933647] raw: 005fff8000008100 ffffea000db44f00 0000000400000004 ffff88036f80ee00 [ 807.942050] raw: 0000000000000000 0000000080190019 00000001ffffffff 0000000000000000 [ 807.950456] page dumped because: kasan: bad access detected [ 807.958240] Memory state around the buggy address: [ 807.963405] ffff88033e635f00: fc fc fc fc fb fb fb fb fb fb fb fc fc fc fc fb [ 807.971288] ffff88033e635f80: fb fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc [ 807.979166] >ffff88033e636000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 807.994882] ^ [ 807.998477] ffff88033e636080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 808.006352] ffff88033e636100: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb [ 808.014230] ================================================================== [ 808.022108] Disabling lock debugging due to kernel taint Fixes: edfaf94f ("net_sched: improve and refactor tcf_action_put_many()") Signed-off-by: NVlad Buslov <vladbu@mellanox.com> Acked-by: NCong Wang <xiyou.wangcong@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Zhenbo Gao 提交于
Remove the following obsolete parameter comments of tipc_topsrv struct: @rcvbuf_cache @tipc_conn_new @tipc_conn_release @tipc_conn_recvmsg @imp @type Add the comments for the missing parameters below of tipc_topsrv struct: @awork @listener Remove the unused or duplicated parameter comments of tipc_conn struct: @outqueue_lock @rx_action Signed-off-by: NZhenbo Gao <zhenbo.gao@windriver.com> Reviewed-by: NYing Xue <ying.xue@windriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hangbin Liu 提交于
man ip-tunnel ttl section says: 0 is a special value meaning that packets inherit the TTL value. IPv4 tunnel respect this in ip_tunnel_xmit(), but IPv6 tunnel has not implement it yet. To make IPv6 behave consistently with IP tunnel, add ipv6 tunnel inherit support. Signed-off-by: NHangbin Liu <liuhangbin@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 9月, 2018 5 次提交
-
-
由 Emmanuel Grumbach 提交于
When tracing is enabled, all the debug messages are recorded and must not exceed MAX_MSG_LEN (100) columns. Longer debug messages grant the user with: WARNING: CPU: 3 PID: 32642 at /tmp/wifi-core-20180806094828/src/iwlwifi-stack-dev/net/mac80211/./trace_msg.h:32 trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211] Workqueue: phy1 ieee80211_iface_work [mac80211] RIP: 0010:trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211] Call Trace: __sdata_dbg+0xbd/0x120 [mac80211] ieee80211_ibss_rx_queued_mgmt+0x15f/0x510 [mac80211] ieee80211_iface_work+0x21d/0x320 [mac80211] Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
If the driver fails to properly prepare for the channel switch, mac80211 will disconnect. If the CSA IE had mode set to 1, it means that the clients are not allowed to send any Tx on the current channel, and that includes the deauthentication frame. Make sure that we don't send the deauthentication frame in this case. In iwlwifi, this caused a failure to flush queues since the firmware already closed the queues after having parsed the CSA IE. Then mac80211 would wait until the deauthentication frame would go out (drv_flush(drop=false)) and that would never happen. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Ilan Peer 提交于
When performing a channel switch flow for a managed interface, the flow did not update the bandwidth of the AP station and the rate scale algorithm. In case of a channel width downgrade, this would result with the rate scale algorithm using a bandwidth that does not match the interface channel configuration. Fix this by updating the AP station bandwidth and rate scaling algorithm before the actual channel change in case of a bandwidth downgrade, or after the actual channel change in case of a bandwidth upgrade. Signed-off-by: NIlan Peer <ilan.peer@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
We hit a problem with iwlwifi that was caused by a bug in mac80211. A bug in iwlwifi caused the firwmare to crash in certain cases in channel switch. Because of that bug, drv_pre_channel_switch would fail and trigger the restart flow. Now we had the hw restart worker which runs on the system's workqueue and the csa_connection_drop_work worker that runs on mac80211's workqueue that can run together. This is obviously problematic since the restart work wants to reconfigure the connection, while the csa_connection_drop_work worker does the exact opposite: it tries to disconnect. Fix this by cancelling the csa_connection_drop_work worker in the restart worker. Note that this can sound racy: we could have: driver iface_work CSA_work restart_work +++++++++++++++++++++++++++++++++++++++++++++ | <--drv_cs ---| <FW CRASH!> -CS FAILED--> | | | cancel_work(CSA) schedule | CSA work | | | Race between those 2 But this is not possible because we flush the workqueue in the restart worker before we cancel the CSA worker. That would be bullet proof if we could guarantee that we schedule the CSA worker only from the iface_work which runs on the workqueue (and not on the system's workqueue), but unfortunately we do have an instance in which we schedule the CSA work outside the context of the workqueue (ieee80211_chswitch_done). Note also that we should probably cancel other workers like beacon_connection_loss_work and possibly others for different types of interfaces, at the very least, IBSS should suffer from the exact same problem, but for now, do the minimum to fix the actual bug that was actually experienced and reproduced. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Dreyfuss, Haim 提交于
In commit 9236c4523e5b ("mac80211: limit wmm params to comply with ETSI requirements"), we have limited the WMM parameters to comply with 802.11 and ETSI standard. Mistakenly the TXOP value was caluclated wrong. Fix it by taking the minimum between 802.11 to ETSI to make sure we are not violating both. Fixes: e552af05 ("mac80211: limit wmm params to comply with ETSI requirements") Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: NLuca Coelho <luciano.coelho@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-