- 30 8月, 2019 3 次提交
-
-
由 Max Staudt 提交于
This is the i2c-icy driver for the ICY board for Amiga computers. It connects a PCF8584 I2C controller to the Zorro bus, providing I2C connectivity. The original documentation can be found on Aminet: https://aminet.net/package/docs/hard/icy IRQ support is currently not implemented, as i2c-algo-pcf is built for the ISA bus and a straight implementation of the same stack locks up a Zorro machine. Signed-off-by: NMax Staudt <max@enpas.org> Reviewed-by: NGeert Uytterhoeven <geert@linux-m68k.org> [wsa: added a missing newline reported by checkpatch] Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Stefan Wahren 提交于
Inspired by Lori Hikichi's patch for iproc, this adds the full name of the devicetree node to the adapter name. With the introduction of BCM2711 it's very difficult to distinguish between the multiple instances. Signed-off-by: NStefan Wahren <wahrenst@gmx.net> Acked-by: NScott Branden <scott.branden@broadcom.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Stefan Wahren 提交于
The I2C block on the BCM2711 isn't affected by the clk stretching bug. So there is no need to apply the corresponding quirk. Signed-off-by: NStefan Wahren <wahrenst@gmx.net> Reviewed-by: NEric Anholt <eric@anholt.net> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
- 14 8月, 2019 2 次提交
-
-
由 Hans de Goede 提交于
When the kernel is build with lockdep support and the i2c-cht-wc driver is used, the following warning is shown: [ 66.674334] ====================================================== [ 66.674337] WARNING: possible circular locking dependency detected [ 66.674340] 5.3.0-rc4+ #83 Not tainted [ 66.674342] ------------------------------------------------------ [ 66.674345] systemd-udevd/1232 is trying to acquire lock: [ 66.674349] 00000000a74dab07 (intel_soc_pmic_chtwc:167:(&cht_wc_regmap_cfg)->lock){+.+.}, at: regmap_write+0x31/0x70 [ 66.674360] but task is already holding lock: [ 66.674362] 00000000d44a85b7 (i2c_register_adapter){+.+.}, at: i2c_smbus_xfer+0x49/0xf0 [ 66.674370] which lock already depends on the new lock. [ 66.674371] the existing dependency chain (in reverse order) is: [ 66.674374] -> #1 (i2c_register_adapter){+.+.}: [ 66.674381] rt_mutex_lock_nested+0x46/0x60 [ 66.674384] i2c_smbus_xfer+0x49/0xf0 [ 66.674387] i2c_smbus_read_byte_data+0x45/0x70 [ 66.674391] cht_wc_byte_reg_read+0x35/0x50 [ 66.674394] _regmap_read+0x63/0x1a0 [ 66.674396] _regmap_update_bits+0xa8/0xe0 [ 66.674399] regmap_update_bits_base+0x63/0xa0 [ 66.674403] regmap_irq_update_bits.isra.0+0x3b/0x50 [ 66.674406] regmap_add_irq_chip+0x592/0x7a0 [ 66.674409] devm_regmap_add_irq_chip+0x89/0xed [ 66.674412] cht_wc_probe+0x102/0x158 [ 66.674415] i2c_device_probe+0x95/0x250 [ 66.674419] really_probe+0xf3/0x380 [ 66.674422] driver_probe_device+0x59/0xd0 [ 66.674425] device_driver_attach+0x53/0x60 [ 66.674428] __driver_attach+0x92/0x150 [ 66.674431] bus_for_each_dev+0x7d/0xc0 [ 66.674434] bus_add_driver+0x14d/0x1f0 [ 66.674437] driver_register+0x6d/0xb0 [ 66.674440] i2c_register_driver+0x45/0x80 [ 66.674445] do_one_initcall+0x60/0x2f4 [ 66.674450] kernel_init_freeable+0x20d/0x2b4 [ 66.674453] kernel_init+0xa/0x10c [ 66.674457] ret_from_fork+0x3a/0x50 [ 66.674459] -> #0 (intel_soc_pmic_chtwc:167:(&cht_wc_regmap_cfg)->lock){+.+.}: [ 66.674465] __lock_acquire+0xe07/0x1930 [ 66.674468] lock_acquire+0x9d/0x1a0 [ 66.674472] __mutex_lock+0xa8/0x9a0 [ 66.674474] regmap_write+0x31/0x70 [ 66.674480] cht_wc_i2c_adap_smbus_xfer+0x72/0x240 [i2c_cht_wc] [ 66.674483] __i2c_smbus_xfer+0x1a3/0x640 [ 66.674486] i2c_smbus_xfer+0x67/0xf0 [ 66.674489] i2c_smbus_read_byte_data+0x45/0x70 [ 66.674494] bq24190_probe+0x26b/0x410 [bq24190_charger] [ 66.674497] i2c_device_probe+0x189/0x250 [ 66.674500] really_probe+0xf3/0x380 [ 66.674503] driver_probe_device+0x59/0xd0 [ 66.674506] device_driver_attach+0x53/0x60 [ 66.674509] __driver_attach+0x92/0x150 [ 66.674512] bus_for_each_dev+0x7d/0xc0 [ 66.674515] bus_add_driver+0x14d/0x1f0 [ 66.674518] driver_register+0x6d/0xb0 [ 66.674521] i2c_register_driver+0x45/0x80 [ 66.674524] do_one_initcall+0x60/0x2f4 [ 66.674528] do_init_module+0x5c/0x230 [ 66.674531] load_module+0x2707/0x2a20 [ 66.674534] __do_sys_init_module+0x188/0x1b0 [ 66.674537] do_syscall_64+0x5c/0xb0 [ 66.674541] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 66.674543] other info that might help us debug this: [ 66.674545] Possible unsafe locking scenario: [ 66.674547] CPU0 CPU1 [ 66.674548] ---- ---- [ 66.674550] lock(i2c_register_adapter); [ 66.674553] lock(intel_soc_pmic_chtwc:167:(&cht_wc_regmap_cfg)->lock); [ 66.674556] lock(i2c_register_adapter); [ 66.674559] lock(intel_soc_pmic_chtwc:167:(&cht_wc_regmap_cfg)->lock); [ 66.674561] *** DEADLOCK *** The problem is that the CHT Whiskey Cove PMIC's builtin i2c-adapter is itself a part of an i2c-client (the PMIC). This means that transfers done through it take adapter->bus_lock twice, once for the parent i2c-adapter and once for its own bus_lock. Lockdep does not like this nested locking. To make lockdep happy in the case of busses with muxes, the i2c-core's i2c_adapter_lock_bus function calls: rt_mutex_lock_nested(&adapter->bus_lock, i2c_adapter_depth(adapter)); But i2c_adapter_depth only works when the direct parent of the adapter is another adapter, as it is only meant for muxes. In this case there is an i2c-client and MFD instantiated platform_device in the parent->child chain between the 2 devices. This commit overrides the default i2c_lock_operations, passing a hardcoded depth of 1 to rt_mutex_lock_nested, making lockdep happy. Note that if there were to be a mux attached to the i2c-wc-cht adapter, this would break things again since the i2c-mux code expects the root-adapter to have a locking depth of 0. But the i2c-wc-cht adapter always has only 1 client directly attached in the form of the charger IC paired with the CHT Whiskey Cove PMIC. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Wolfram Sang 提交于
In the general move to have i2c_new_*_device functions which return ERR_PTR instead of NULL, this patch converts i2c_new_secondary_device(). There are only few users, so this patch converts the I2C core and all users in one go. The function gets renamed to i2c_new_ancillary_device() so out-of-tree users will get a build failure to understand they need to adapt their error checking code. Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> # adv748x Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # adv7511 + adv7604 Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # adv7604 Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
- 07 8月, 2019 5 次提交
-
-
由 Baolin Wang 提交于
The 'enable' clock of I2C master is required, we should return an error if failed to get the 'enable' clock, to make sure the I2C driver can be defer probe if the clock resource is not ready. Signed-off-by: NBaolin Wang <baolin.wang@linaro.org> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Baolin Wang 提交于
Use the new helper that wraps the calls to platform_get_resource() and devm_ioremap_resource() together. Signed-off-by: NBaolin Wang <baolin.wang@linaro.org> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Baolin Wang 提交于
Now there is no need to keep our I2C driver to be initialized so early, thus changing to module level and let it can be built as a module, meanwhile adding some module information. Signed-off-by: NBaolin Wang <baolin.wang@linaro.org> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Andy Shevchenko 提交于
of_find_property() will return NULL if of_node is NULL, thus of_irq_get_by_name() returns -EINVAL which we ignore, so no need to double check. Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Shaokun Zhang 提交于
drivers/i2c/busses/i2c-designware-master.c: In function ‘i2c_dw_init_recovery_info’: drivers/i2c/busses/i2c-designware-master.c:658:6: warning: unused variable ‘r’ [-Wunused-variable] int r; ^ Fixes: 33eb09a0 ("i2c: designware: make use of devm_gpiod_get_optional") Signed-off-by: NShaokun Zhang <zhangshaokun@hisilicon.com> Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
- 01 8月, 2019 6 次提交
-
-
由 Uwe Kleine-König 提交于
There is a semantical change: if devm_gpiod_get_optional returns -ENOSYS this is passed as error to the caller. This effectively reverts commit d1fa7452 ("i2c: designware: Consider SCL GPIO optional") which shouldn't be necessary any more since gpiod_get_optional doesn't return -ENOSYS any more with GPIOLIB=n. Signed-off-by: NUwe Kleine-König <uwe@kleine-koenig.org> Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Chuhong Yuan 提交于
Instead of using to_pci_dev + pci_get_drvdata, use dev_get_drvdata to make code simpler. Signed-off-by: NChuhong Yuan <hslester96@gmail.com> Reviewed-by: NJean Delvare <jdelvare@suse.de> Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Anson Huang 提交于
Use the new helper devm_platform_ioremap_resource() which wraps the platform_get_resource() and devm_ioremap_resource() together, to simplify the code. Signed-off-by: NAnson Huang <Anson.Huang@nxp.com> Acked-by: NDong Aisheng <aisheng.dong@nxp.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Anson Huang 提交于
Use the new helper devm_platform_ioremap_resource() which wraps the platform_get_resource() and devm_ioremap_resource() together, to simplify the code. Signed-off-by: NAnson Huang <Anson.Huang@nxp.com> Reviewed-by: NDong Aisheng <aisheng.dong@nxp.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Fuqian Huang 提交于
In commit 518a2f19 ("dma-mapping: zero memory returned from dma_alloc_*"), dma_alloc_coherent has already zeroed the memory. So memset is not needed. Acked-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NFuqian Huang <huangfq.daxian@gmail.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Dmitry Osipenko 提交于
The I2C driver fails to probe if CONFIG_PM_SLEEP=n because runtime PM doesn't depend on the PM sleep and in this case the runtime PM ops are not included in the driver, resulting in I2C clock not being enabled. It's much cleaner to simply allow compiler to remove the dead code instead of messing with the #ifdefs. This patch fixes such errors when CONFIG_PM_SLEEP=n: tegra-i2c 7000c400.i2c: timeout waiting for fifo flush tegra-i2c 7000c400.i2c: Failed to initialize i2c controller Signed-off-by: NDmitry Osipenko <digetx@gmail.com> Acked-by: NJon Hunter <jonathanh@nvidia.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
- 17 7月, 2019 1 次提交
-
-
由 Mauro Carvalho Chehab 提交于
Some files got renamed but probably due to some merge conflicts, a few references still point to the old locations. Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
- 06 7月, 2019 4 次提交
-
-
由 YueHaibing 提交于
Remove .owner field if calls are used which set it automatically Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Signed-off-by: NYueHaibing <yuehaibing@huawei.com> Reviewed-by: NStefan Roese <sr@denx.de> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Vasyl Gomonovych 提交于
Generated by: alloc_cast.cocci Signed-off-by: NVasyl Gomonovych <gomonovych@gmail.com> Acked-by: NJochen Friedrich <jochen@scram.de> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Jarkko Nikula 提交于
Add SMBUS PCI ID for Intel Tiger Lake -LP. Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Jarkko Nikula 提交于
I managed to break sorting in PCI ID defines in my last two patches: commit 5cd1c56c ("i2c: i801: Add support for Intel Comet Lake") commit 9be1485a ("i2c: i801: Add support for Intel Elkhart Lake") Fix them up. Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
- 29 6月, 2019 7 次提交
-
-
由 Fabrice Gasnier 提交于
This patch adds the support of I2C_SMBUS_I2C_BLOCK_DATA transaction type for the stm32f7 SMBUS Controller. Use emulated I2C_SMBUS_I2C_BLOCK_DATA transactions as there is no specific hardware in STM32 I2C to manage this (e.g. like no need for PEC here). Emulated transfer will fall back calling i2c transfer method where there's already support for DMAs for example. So, use the I2C_FUNC_SMBUS_I2C_BLOCK in stm32f7_i2c_func(), and rely on emulated transfer by returning -EOPNOTSUPP in the smbus_xfer() routine for such a case. Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com> Reviewed-by: NPierre-Yves MORDRET <pierre-yves.mordret@st.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Charles Keepax 提交于
Only set init_irq during i2c_device_new and only handle client->irq on the probe/remove paths. Suggested-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com> Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Charles Keepax 提交于
It makes sense to contain all the ACPI IRQ handling in a single helper function. Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com> Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Charles Keepax 提交于
Bring the ACPI path in sync with the device tree path and handle all the IRQ fetching at probe time. This leaves the only IRQ handling at device registration time being that which is passed directly through the board info as either a resource or an actual IRQ number. Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com> Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Charles Keepax 提交于
In preparation for future refactoring factor out the fetch of the IRQ into its own helper function. Whilst we are at it update the handling to return the actual error code returned from acpi_dev_get_resources as well. Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com> Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Charles Keepax 提交于
Use the available IRQ helper functions, most of the functions have additional helpful side affects like configuring the trigger type of the IRQ. Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com> Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Charles Keepax 提交于
Remove the static from i2c_dev_irq_from _resources so that other parts of the core code can use this helper function. Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
- 26 6月, 2019 5 次提交
-
-
由 Stefan Roese 提交于
This patch adds a driver for the I2C controller found on the MediaTek MT7621/7628/7688 SoC's. The base version of this driver was done by Steven Liu (according to the copyright and MODULE_AUTHOR lines). It can be found in the OpenWRT repositories (v4.14 at the time I looked). The base driver had many issues, which are disccussed here: https://en.forum.labs.mediatek.com/t/openwrt-15-05-loads-non-working-i2c-kernel-module-for-mt7688/1286/3 >From this link an enhanced driver version (complete rewrite, mayor changes: support clock stretching, repeated start, ACK handling and unlimited message length) from Jan Breuer can be found here: https://gist.github.com/j123b567/9b555b635c2b4069d716b24198546954 This patch now adds this enhanced I2C driver to mainline. Changes by Stefan Roese for upstreaming: - Add devicetree bindings - checkpatch clean - Use module_platform_driver() - Minor cosmetic enhancements - Removed IO warpped functions - Use readl_relaxed_poll_timeout() and drop poll_down_timeout() - Removed superfluous barrier() in mtk_i2c_reset() - Use i2c_8bit_addr_from_msg() - Added I2C_FUNC_PROTOCOL_MANGLING - Removed adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; Signed-off-by: NStefan Roese <sr@denx.de> Tested-by: NRené van Dorst <opensource@vdorst.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Wolfram Sang 提交于
We are using sysfs functions directly, so we should include the header. Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Annaliese McDermond 提交于
Probe function fails to recognize that upstream clock actually doesn't yet exist because clock driver has not been initialized. Actually try to go get the clock and test for its existence before trying to set up a downstream clock based upon it. This fixes a bug that causes the i2c driver not to work with monolithic kernels. Fixes: bebff81f ("i2c: bcm2835: Model Divider in CCF") Signed-off-by: NAnnaliese McDermond <nh6z@nh6z.net> Acked-by: NStefan Wahren <wahrenst@gmx.net> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Annaliese McDermond 提交于
If any of the clock code in the probe fails and returns, the IRQ will not be freed. Moving the IRQ request to last allows it to be freed on any errors further up in the probe function. devm_ calls can apparently not be used because there are some potential race conditions that will arise. Fixes: bebff81f ("i2c: bcm2835: Model Divider in CCF") Signed-off-by: NAnnaliese McDermond <nh6z@nh6z.net> Acked-by: NStefan Wahren <wahrenst@gmx.net> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Wolfram Sang 提交于
Nobody (including me) noticed that these functions were exported but not added to the header :/ Fixes: 7159dbda ("i2c: core: improve return value handling of i2c_new_device and i2c_new_dummy") Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: NBartosz Golaszewski <bgolaszewski@baylibre.com> Reviewed-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
- 24 6月, 2019 2 次提交
-
-
由 Suzuki K Poulose 提交于
The driver_find_device() accepts a match function pointer to filter the devices for lookup, similar to bus/class_find_device(). However, there is a minor difference in the prototype for the match parameter for driver_find_device() with the now unified version accepted by {bus/class}_find_device(), where it doesn't accept a "const" qualifier for the data argument. This prevents us from reusing the generic match functions for driver_find_device(). For this reason, change the prototype of the driver_find_device() to make the "match" parameter in line with {bus/class}_find_device() and adjust its callers to use the const qualifier. Also, we could now promote the "data" parameter to const as we pass it down as a const parameter to the match functions. Cc: Corey Minyard <minyard@acm.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Peter Oberparleiter <oberpar@linux.ibm.com> Cc: Sebastian Ott <sebott@linux.ibm.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Nehal Shah <nehal-bakulchandra.shah@amd.com> Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Suzuki K Poulose 提交于
There is an arbitrary difference between the prototypes of bus_find_device() and class_find_device() preventing their callers from passing the same pair of data and match() arguments to both of them, which is the const qualifier used in the prototype of class_find_device(). If that qualifier is also used in the bus_find_device() prototype, it will be possible to pass the same match() callback function to both bus_find_device() and class_find_device(), which will allow some optimizations to be made in order to avoid code duplication going forward. Also with that, constify the "data" parameter as it is passed as a const to the match function. For this reason, change the prototype of bus_find_device() to match the prototype of class_find_device() and adjust its callers to use the const qualifier in accordance with the new prototype of it. Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Andreas Noever <andreas.noever@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Corey Minyard <minyard@acm.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: David Kershner <david.kershner@unisys.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: David Airlie <airlied@linux.ie> Cc: Felipe Balbi <balbi@kernel.org> Cc: Frank Rowand <frowand.list@gmail.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Harald Freudenberger <freude@linux.ibm.com> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jonathan Cameron <jic23@kernel.org> Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: Len Brown <lenb@kernel.org> Cc: Mark Brown <broonie@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michael Jamet <michael.jamet@intel.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Peter Oberparleiter <oberpar@linux.ibm.com> Cc: Sebastian Ott <sebott@linux.ibm.com> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Yehezkel Bernat <YehezkelShB@gmail.com> Cc: rafael@kernel.org Acked-by: NCorey Minyard <minyard@acm.org> Acked-by: NDavid Kershner <david.kershner@unisys.com> Acked-by: NMark Brown <broonie@kernel.org> Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org> Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts Acked-by: NRob Herring <robh@kernel.org> Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 22 6月, 2019 5 次提交
-
-
由 Wolfram Sang 提交于
We are using sysfs functions directly, so we should include the header. Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: NPeter Rosin <peda@axentia.se>
-
由 Linus Walleij 提交于
This switches the i801 GPIO mux to use GPIO descriptors for handling the GPIO lines. The previous hack which was reaching inside the GPIO chips etc cannot live on. We pass descriptors along with the GPIO mux device at creation instead. The GPIO mux was only used by way of platform data with a platform device from one place in the kernel: the i801 i2c bus driver. Let's just associate the GPIO descriptor table with the actual device like everyone else and dynamically create a descriptor table passed along with the GPIO i2c mux. This enables simplification of the GPIO i2c mux driver to use only the descriptor API and the OF probe path gets simplified in the process. The i801 driver was registering the GPIO i2c mux with PLATFORM_DEVID_AUTO which would make it hard to predict the device name and assign the descriptor table properly, but this seems to be a mistake to begin with: all of the GPIO mux devices are hardcoded to look up GPIO lines from the "gpio_ich" GPIO chip. If there are more than one mux, there is certainly more than one gpio chip as well, and then we have more serious problems. Switch to PLATFORM_DEVID_NONE instead. There can be only one. Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Peter Rosin <peda@axentia.se> Cc: Jean Delvare <jdelvare@suse.com> Signed-off-by: NSerge Semin <fancer.lancer@gmail.com> Signed-off-by: NLinus Walleij <linus.walleij@linaro.org> Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com> [Removed a newline, suggested by Andy. /Peter] Signed-off-by: NPeter Rosin <peda@axentia.se>
-
由 Bitan Biswas 提交于
The usage of BUG() macro is generally discouraged in kernel, unless it's a problem that results in a physical damage or loss of data. This patch removes unnecessary BUG() macros and replaces the rest with warning. Signed-off-by: NBitan Biswas <bbiswas@nvidia.com> Reviewed-by: NDmitry Osipenko <digetx@gmail.com> Tested-by: NDmitry Osipenko <digetx@gmail.com> Acked-by: NThierry Reding <treding@nvidia.com> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Jarkko Nikula 提交于
Add PCI ID for Intel Elkhart Lake PCH. Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-
由 Alexander Sverdlin 提交于
Add SMBUS 2.0 Block Write-Block Read Process Call command support. Signed-off-by: NAlexander Sverdlin <alexander.sverdlin@nokia.com> Reviewed-by: NJean Delvare <jdelvare@suse.de> Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
-