Update the DaVinci GPIO code to work better on non-dm6446 parts,
notably the dm355:

 - Only handle the number of GPIOs the chip actually has.  So
   for example on dm6467, GPIO-42 is the last GPIO, and trying
   to use GPIO-43 now fails cleanly; or GPIO-72 on dm6446.

 - Enable GPIO interrupts on each 16-bit GPIO-irq bank ...
   previously, only the first five were enabled, so GPIO-80
   and above (on dm355) wouldn't trigger IRQs.

 - Use the right IRQ for each GPIO bank.  The wrong values were
   used for dm355 chips, so GPIO IRQs got routed incorrectly.

 - Handle up to four pairs of 16-bit GPIO banks ... previously
   only three were handled, so accessing GPIO-96 and up (e.g. on
   dm355) would oops.

 - Update several comments that were dm6446-specific.

Verified by receiving GPIO-1 (dm9000) and GPIO-5 (msp430) IRQs
on the DM355 EVM.

One thing this doesn't do is handle the way some of the GPIO
numbers on dm6467 are reserved but aren't valid as GPIOs.  Some
bitmap logic could fix that if needed.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Add arch-specific ioremap() which uses any existing static mappings in
place of doing a new mapping.  From now on, drivers should always use
ioremap() instead of IO_ADDRESS().

In addition, remove the davinci_[read|write]* macros in favor of using
ioremap.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Switch DaVinci SOC gpios over to using the new GPIO library, so it can
access GPIO expanders and other non-SOC GPIOs using the same calls.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This fixes a build problem with GPIOs on DaVinci.  Since it inlines
operations for on-chip GPIOs, it needs some headers to support those
direct register accesses.  Those headers won't be included on other
platforms, since they don't have that optimization.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NKevin Hilman <khilman@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support GPIO driver for TI DaVinci SoC
Signed-off-by: NVladimir Barinov <vbarino@ru.mvista.com>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Acked-by: NKevin Hilman <khilman@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>