Reset HTT stats helps to get the aggregated HTT stats via
tracing and also we can clear the accumulated HTT stats with
this debugfs file.
Signed-off-by: NMaharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Extended the bit mask value of the HTT stats to get the Mu-MIMO
related stats via tracing.
Signed-off-by: NMaharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In Talyn the HW is responsible for power management enter / exit
flow, hence the deep sleep exit latency is significantly shorter than
in Sparrow.
In such a case HALP feature, that is meant to prevent long PCIe blocking
accesses, is no longer needed and can be removed for Talyn.
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make sure rx_buff_mgmt is initialized before accessing it.
Signed-off-by: NDedy Lansky <dlansky@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When MISC interrupt is triggered due to HALP bit, in parallel
to mbox events handling by the MISC threaded IRQ, new mbox
interrupt can be missed in the following scenario:
1. MISC ICR is read in the IRQ handler
2. Threaded IRQ is completed and all MISC interrupts are unmasked
3. mbox interrupt is set by FW
4. HALP is masked
The mbox interrupt in step 3 can be missed due to constant high level
of ICM.
Masking all MISC IRQs instead of masking only HALP bit in step 4
will guarantee that ICM will drop to 0 and interrupt will be triggered
once MISC interrupts will be unmasked.
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Save the parameter of max_assoc_sta per device.
On fw_ready event calculate the max_assoc_sta and save it per device,
do not overwrite the max_assoc_sta module param.
Signed-off-by: NAhmad Masri <amasri@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add printing of hwhead as part of desc ring and status ring debugfs.
Validate wil->rx_buff_mgmt and ring->ctx arrays before accessing them.
Dump Tx descriptor content even when it indicates invalid buff_id.
Signed-off-by: NDedy Lansky <dlansky@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Current board file loading procedure assumes that the board file
includes only one section.
New board files can include multiple sections.
Add the ability to read multiple addresses and max size from FW
file and load multiple sections from the board file into those
addresses.
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add logging of the platform capabilities after retrieving it from the
platform driver.
Signed-off-by: NDedy Lansky <dlansky@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

_desc is defined in __wil_tx_vring_tso() and may not be set in
case len is 0, verify _desc is set.
Signed-off-by: NAlexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Interrupt is set in ICM (ICR & ~IMV) rising trigger.
As the driver masks the IRQ after clearing it, there can
be a race where an additional spurious interrupt is triggered
when the driver unmask the IRQ.
This can happen in case HW triggers an interrupt after the clear
and before the mask.

To prevent the second spurious interrupt the driver needs to mask the
IRQ before reading and clearing it.
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

clang fails to eliminate some dead code with always-taken branches
when CONFIG_PROFILE_ANNOTATED_BRANCHES is set, leading to a false-positive
warning:

drivers/net/wireless/ath/carl9170/mac.c:522:3: error: variable 'power' is used uninitialized whenever 'if' condition is
      false [-Werror,-Wsometimes-uninitialized]
                BUG_ON(1);
                ^~~~~~~~~

Change both instances of BUG_ON(1) in carl9170 to the simpler BUG()
to avoid the warning.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NChristian Lamparter <chunkeey@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Notice that *rc* can evaluate to up to 5, include/linux/netdevice.h:

enum gro_result {
        GRO_MERGED,
        GRO_MERGED_FREE,
        GRO_HELD,
        GRO_NORMAL,
        GRO_DROP,
        GRO_CONSUMED,
};
typedef enum gro_result gro_result_t;

In case *rc* evaluates to 5, we end up having an out-of-bounds read
at drivers/net/wireless/ath/wil6210/txrx.c:821:

	wil_dbg_txrx(wil, "Rx complete %d bytes => %s\n",
		     len, gro_res_str[rc]);

Fix this by adding element "GRO_CONSUMED" to array gro_res_str.

Addresses-Coverity-ID: 1444666 ("Out-of-bounds read")
Fixes: 194b482b ("wil6210: Debug print GRO Rx result")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Increase pulse width range from 1-2usec to 0-4usec.
During data traffic HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the success rate.

Tested ath10k hw and fw:
	* QCA9888(10.4-3.5.1-00052)
	* QCA4019(10.4-3.2.1.1-00017)
	* QCA9984(10.4-3.6-00104)
	* QCA988X(10.2.4-1.0-00041)

Tested ath9k hw: AR9300
Tested-by: NTamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: NTamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

AR9330, AR9485, AR9531, AR9550, AR9561 and AR9565 all use same
channel set register configuration which allows for small code
size reduction.
Signed-off-by: NTomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Remove duplicate NO_CTL that is just 2 lines below.
Signed-off-by: NTomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_count_frames':
drivers/net/wireless/ath/ath9k/xmit.c:413:25: warning: variable 'fi' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_complete_aggr':
drivers/net/wireless/ath/ath9k/xmit.c:449:24: warning: variable 'hdr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_start':
drivers/net/wireless/ath/ath9k/xmit.c:2274:18: warning: variable 'avp' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/ath/ath9k/xmit.c:2269:24: warning: variable 'hdr' set but not used [-Wunused-but-set-variable]

These variables are not used any more
and can be removed.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The ath9k driver uses as maximum allowed txpower the constant
MAX_RATE_POWER. It is used to set a maximum txpower limit for the PHY
(which is combined txpower) and also the maximum txpower for per chain
rates. Its value 63 is derived from the maximum number the registers can
store for the per chain txpower.

The max txpower a user can set because of this is 31 dBm (floor(63 / 2)).
This also means that a device with multiple tx chains is even limited
further:

* 1 chain:  31 dBm per chain
* 2 chains: 28 dBm per chain
* 3 chains: 26 dBm per chain

This combined txpower limit of 31 dBm becomes even more problematic when
some extra antenna gain is set in the EEPROM. A high power device is then
no longer able to reach its potential limits.

Instead the code dealing with the combined txpower must use a higher limit
than 63 and only the code dealing with the per chain txpower have to use
the limit of 63. Since the antenna gain can be quite large and 8 bit
variables are often used in ath9k for txpower, a large, divisible by two
number like 254 is a good choice for this new limit.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Right now, if an error is encountered during the SREV register
read (i.e. an EIO in ath9k_regread()), that error code gets
passed all the way to __ath9k_hw_init(), where it is visible
during the "Chip rev not supported" message.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

Check for -EIO explicitly in ath9k_hw_read_revisions() and return
a boolean based on the success of the operation. Check for that in
__ath9k_hw_init() and abort with a more debugging-friendly message
if reading the revisions wasn't successful.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Failed to read SREV register
    ath: phy2: Could not read hardware revision
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

This helps when debugging by directly showing the first point of
failure and it could prevent possible errors if a 0x0f.3 revision
is ever supported.
Signed-off-by: NTim Schumacher <timschumi@gmx.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

As already noted a comment in ath_tx_complete_aggr(), the hardware will
occasionally send a TX status with the wrong tid number. If we trust the
value, airtime usage will be reported to the wrong AC, which can cause the
deficit on that AC to become very low, blocking subsequent attempts to
transmit.

To fix this, account airtime usage to the TID number from the original skb,
instead of the one in the hardware TX status report.
Reported-by: NMiguel Catalan Cid <miguel.catalan@i2cat.net>
Signed-off-by: NToke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The check on status not being zero is redundant as previous code
paths that set status to an error value break out of the while
loop and hence status is never non-zero at the check. Remove
this redundant code.

Addresses-Coverity: ("Logically dead code")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NMukesh Ojha <mojha@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The "ev->traffic_class" and "reply->ac" variables come from the network
and they're used as an offset into the wmi->stream_exist_for_ac[] array.
Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[]
array only has WMM_NUM_AC (4) elements.  We need to add a couple bounds
checks to prevent array overflows.

I also modified one existing check from "if (traffic_class > 3) {" to
"if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.

Fixes: bdcd8170 (" Add ath6kl cleaned up driver")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, replace code of the following form:

sizeof(*ev) + ev->num_neighbors * sizeof(struct wmi_neighbor_info)

with:

struct_size(ev, neighbor, ev->num_neighbors)

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, change the following form:

sizeof(*tbl) + num_entries * sizeof(struct wmi_bss_roam_info)

 to :

struct_size(tbl, info, num_entries)

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Invalid rate code is sent to firmware when multicast rate value of 0 is
sent to driver indicating disabled case, causing broken mesh path.
so fix that.

Tested on QCA9984 with firmware 10.4-3.6.1-00827

Sven tested on IPQ4019 with 10.4-3.5.3-00057 and QCA9888 with 10.4-3.5.3-00053
(ath10k-firmware) and 10.4-3.6-00140 (linux-firmware 2018-12-16-211de167).

Fixes: cd93b83a ("ath10k: support for multicast rate control")
Co-developed-by: NZhi Chen <zhichen@codeaurora.org>
Signed-off-by: NZhi Chen <zhichen@codeaurora.org>
Signed-off-by: NPradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Tested-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

After implementing PN replay check we can enable SDIO support on QCA6174.
Tested with client mode on all security modes, and fragmentation as well. AP
mode does not work yet.

Also tone down the warning about SDIO being not ready yet.

Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. AP mode
is not working yet.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On high latency devices (SDIO, USB) ath10k did not handle fragmented frames and
all fragmented frames on receive path were lost in ath10k. Even a simple ping
test failed with fragmentation.

The fragmented packets are decapsulated based on the security mode, then the PN
is checked and the fragmented frame is passed to mac80211.  mac80211 in
ieee80211_rx_h_defragment() will then combine the fragment frames and forward
to upper layers.

Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On high latency devices (SDIO, USB) ath10k did not do PN replay check, a data
frame with an invalid PN number was not discard as it should have been. So this
patch implements PN replay in ath10k. PN replay check for fragmented frames is
implemented in followup patch.

With low latency devices (PCI, AHB) hardware can store the data
frames's content to host memory directly and the firmware can fully reorder
data frames, and do PN replay check at the same time. But for high latency
devices all data frames will be received and stored in firmware's memory and it
is hard to do full reorder because of the memory size limitations in the
firmware. This is why the PN replay protections needs to be implemented in host
driver.

Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add the handler for HTT_T2H_MSG_TYPE_SEC_IND event from firmware, which stores
PN for replay check implemented in the following patch.

Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add the struct for PN replay protection and fragment packet
handler.

Also fix the bitmask of HTT_RX_DESC_HL_INFO_MCAST_BCAST to match what's currently
used by SDIO firmware. The defines are not used yet so it's safe to modify
them. Remove the conflicting HTT_RX_DESC_HL_INFO_FRAGMENT as
it's not either used in ath10k.

Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Although not likely, the bundle allocation might fail.
Add proper error check and warning print.
Signed-off-by: NErik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

HTC header carries junk values that may be interpreted by the firmware
differently. Enable credit update only if flow control is enabled for
the corresponding endpoint.
Signed-off-by: NAlagu Sankar <alagusankar@silex-india.com>
Signed-off-by: NErik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With SDIO there's a use after free after a data frame is transfered, call stack
below. This happens because ath10k_htt_tx_hl() directly transmits the skb
provided by mac80211 using ath10k_htc_send(), all other HTT functions use
separate skb created with ath10k_htc_alloc_skb() to transmit the HTC packet.
After the packet is transmitted mac80211 frees the skb in ieee80211_tx_status()
but HTT layer expects  that it still owns the skb, and frees it in
ath10k_htt_htc_tx_complete().

To fix this take a reference of skb before sending it to HTC layer to make sure
we still own the skb.

Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
ath10k_htt_tx_hl() is only used by SDIO and USB so other busses (PCI, AHB and
SNOC) should be unaffected.

call stack of use-after-free:
dump_backtrace+0x0/0x2d8
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0xc8/0xec
print_address_description+0x74/0x240
kasan_report+0x258/0x274
__asan_report_load4_noabort+0x20/0x28
skb_pull+0xbc/0x114
ath10k_htc_notify_tx_completion+0x190/0x2a4 [ath10k_core]
ath10k_sdio_write_async_work+0x1e4/0x2c4 [ath10k_sdio]
process_one_work+0x3d8/0x8b0
worker_thread+0x518/0x7e0
kthread+0x260/0x278
ret_from_fork+0x10/0x18

Allocated by one task:
kasan_kmalloc+0xa0/0x13c
kasan_slab_alloc+0x14/0x1c
kmem_cache_alloc+0x144/0x208
__alloc_skb+0xec/0x394
alloc_skb_with_frags+0x8c/0x374
sock_alloc_send_pskb+0x520/0x5d4
sock_alloc_send_skb+0x40/0x50
__ip_append_data+0xf5c/0x1858
ip_make_skb+0x194/0x1d4
udp_sendmsg+0xf24/0x1ab8
inet_sendmsg+0x1b0/0x2e0
sock_sendmsg+0x88/0xa0
__sys_sendto+0x220/0x3a8
__arm64_sys_sendto+0x78/0x80
el0_svc_common+0x120/0x1e0
el0_svc_compat_handler+0x64/0x80
el0_svc_compat+0x8/0x18

Freed by another task:
__kasan_slab_free+0x120/0x1d4
kasan_slab_free+0x10/0x1c
kmem_cache_free+0x74/0x504
kfree_skbmem+0x88/0xc8
__kfree_skb+0x24/0x2c
consume_skb+0x114/0x18c
__ieee80211_tx_status+0xb7c/0xf60 [mac80211]
ieee80211_tx_status+0x224/0x270 [mac80211]
ath10k_txrx_tx_unref+0x564/0x950 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x178c/0x2a38 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x20/0x30 [ath10k_core]
ath10k_sdio_irq_handler+0xcc0/0x1654 [ath10k_sdio]
process_sdio_pending_irqs+0xec/0x358
sdio_run_irqs+0x68/0xe4
sdio_irq_work+0x1c/0x28
process_one_work+0x3d8/0x8b0
worker_thread+0x518/0x7e0
kthread+0x260/0x278
ret_from_fork+0x10/0x18
Reported-by: NWen Gong <wgong@codeaurora.org>
Tested-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Transmit completion for SDIO is similar to PCIe, modify the high
latency path to allow SDIO modules to use the msdu id.

kvalo: the original patch from Alagu enabled this only for SDIO but I'm not
sure should we also enable this with USB. I'll use bus params to enable this
for so that it's easy to enable also for USB later.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NAlagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This way we don't need to set every variable and give them to default, which is
zero. This is also safer in case we forgot to initalise a new field in some of
the bus modules.

Compile tested only.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

HTT High Latency (ATH10K_DEV_TYPE_HL) does not use txdone_fifo at all, we don't
even initialise it by skipping ath10k_htt_tx_alloc_buf() in
ath10k_htt_tx_start(). Because of this using QCA6174 SDIO
ath10k_htt_rx_tx_compl_ind() will crash when it accesses unitialised
txdone_fifo. So skip txdone_fifo when using High Latency mode.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NAlagu Sankar <alagusankar@silex-india.com>
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Disabling interrupts this early meant WMI communication was not working anymore
when the SDIO device was removed. But we call ath10k_core_unregister() that
will eventually call ath10k_sdio_hif_stop(), which disables the interrupts. So
there's actually no need to disable interrupts here.

Also remove cancel_work_sync() as it's also called in ath10k_sdio_hif_stop().

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On QCA6174 SDIO devices the SDIO interrupt will fail if UART is
disabled from ath10k. SDIO firmware enables UART printouts by
default. If ath10k will try to enable UART again the firmware
will configure it's GPIO line incorrectly and SDIO interrupts
won't work anymore. The workaround is to set UART pin again (19
for QCA6174 SDIO) if uart_print is 0.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: NWen Gong <wgong@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ath.git patches for 5.2. No major changes.

David Bauer says:

====================
net: add reset-controller driven PHY reset

This patchset adds support for a PHY reset driven by a reset-controller.
Currently, only GPIO driven resets are supported by the PHY subsystem.
It also renames the reset-gpio from 'reset' to 'reset_gpio' to
better differentiate between resets wired to a GPIO and resets wired to
a reset-controller driven pin.

Some systems have the PHY reset-line wired to a pin controlled by a
reset-controller (eg. some Atheros AR9132 based boards). In case the
bootloader asserts reset before loading the kernel, we currently do not
have a clean way of deasserting reset to probe the PHY.

v3:
 - add missing newline in mdio_bus.c

v2:
 - fixed missed rename of "reset" in at803x.c
 - move initial reset to mdio_device_reset
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>