Lower limit of burst size configuration is dependent on system type. Add a
datum to track the value. Initialize as appropriate in mlxsw_spX_init().
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the port speeds grow, the current value of "unlimited shaper",
200000000Kbps, might become lower than the actually supported speeds. Bump
it to the maximum value that fits in the corresponding QEEC field, which is
about 2.1Tbps.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The QEEC register configures scheduling elements. One of the bits of
configuration is the burst size to use for the shaper installed on the
element. Add the necessary fields to support this configuration.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the RED Qdisc is unoffloaded, it needs to reduce the reported backlog
by the amount that is in the HW, so that only the SW backlog is contained
in the counter. The same thing will need to be done by TBF, and likely any
other leaf Qdisc as well.

Extract a helper mlxsw_sp_qdisc_leaf_unoffload() and call it from
mlxsw_sp_qdisc_red_unoffload().
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a wrapper around mlxsw_sp_qdisc_collect_tc_stats() and
mlxsw_sp_qdisc_update_stats() for the simple case of doing both in one go:
mlxsw_sp_qdisc_get_class_stats(). Dispatch to that function from
mlxsw_sp_qdisc_get_red_stats(). This new function will be useful for other
leaf Qdiscs as well.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract from mlxsw_sp_qdisc_get_prio_stats() two new functions:
mlxsw_sp_qdisc_collect_tc_stats() to accumulate stats for that one TC only,
and mlxsw_sp_qdisc_update_stats() that makes the stats relative to base
values stored earlier. Use them from mlxsw_sp_qdisc_get_red_stats().
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Acked-by: NTimur Tabi <timur@kernel.org>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend stats group array of uplink representor with all stats that are
available for PF in legacy mode, besides ipsec and TLS which are not
supported.

Don't output vport stats for uplink representor because they are already
handled by 802_3 group (with different names: {tx|rx}_{bytes|packets}_phy).
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Q counters were disabled for all types of representors to prevent an issue
where there is not enough resources to init q counters for 127 representor
instances. Enable q counters only for uplink representors to support
"rx_out_of_buffer", "rx_if_down_packets" counters in ethtool.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In order to support all of the supported stats that are available in legacy
mode for switchdev uplink representors, convert rep stats infrastructure to
reuse struct mlx5e_stats_grp that is already used when device is in legacy
mode. Refactor rep code to use array of mlx5e_stats_grp
structures (constructed using macros provided by stats infra) to
fill/update stats, instead of fixed hardcoded set of values. This approach
allows to easily extend representors with new stats types.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Don't copy all of the stats groups used for mlx5e ethernet NIC profile,
have a separate stats groups for IPoIB with the set of the needed stats
only.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Convert stats groups array to array of "stats group" pointers to allow
sharing and individual selection of groups per profile as illustrated in
the next patches.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

Introduce new macros to declare stats callbacks and groups, for better
code reuse and for individual groups selection per profile which will be
introduced in next patches.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

Attach stats groups array to the profiles and make the stats utility
functions (get_num, update, fill, fill_strings) generic and use the
profile->stats_grps rather the hardcoded NIC stats groups.

This will allow future extension to have per profile stats groups.

In this patch mlx5e NIC and IPoIB will still share the same stats
groups.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

Clean up the code and allows to call uplink rep init/cleanup
from different location later.
To be used later for a new uplink representor mode.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NEli Britstein <elibr@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Allow connecting SW steering source table to a lower/same level
destination table.
Lifting this limitation is required to support Connection Tracking.
Signed-off-by: NYevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Modify header supports ADD/SET and from this patch
also COPY. Copy allows to copy header fields and
metadata.
Signed-off-by: NHamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Modify set actions are not supported on both tx
and rx, added a check for that.
Also refactored the code in a way that every modify
action has his own functions, this needed so in the
future we could add copy action more smoothly.
Signed-off-by: NHamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In the flowtables offload all the devices in the flowtables
share the same flow_block. An offload rule will be installed on
all the devices. This scenario is not correct.

It is no problem if there are only two devices in the flowtable,
The rule with ingress and egress on the same device can be reject
by driver.

But more than two devices in the flowtable will install the wrong
rules on hardware.

For example:
Three devices in a offload flowtables: dev_a, dev_b, dev_c

A rule ingress from dev_a and egress to dev_b:
The rule will install on device dev_a.
The rule will try to install on dev_b but failed for ingress
and egress on the same device.
The rule will install on dev_c. This is not correct.

The flowtables offload avoid this case through restricting the ingress dev
with FLOW_DISSECTOR_KEY_META.

So the mlx5e driver also should support the FLOW_DISSECTOR_KEY_META parse.
Signed-off-by: Nwenxu <wenxu@ucloud.cn>
Acked-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fix the following sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_chains.c:35:20: warning: symbol 'ESW_POOLS' was not declared. Should it be static?

Fixes: 39ac237c ("net/mlx5: E-Switch, Refactor chains and priorities")
Signed-off-by: NChen Wandun <chenwandun@huawei.com>
Acked-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

since mlx5 hardware can segment correctly TSO packets on VXLAN over VLAN
topologies, CPU usage can improve significantly if we enable tunnel
offloads in dev->vlan_features, like it was done in the past with other
NIC drivers (e.g. mlx4, be2net and ixgbe).
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Use "%zu" for size_t. Seen on ARM allmodconfig:

drivers/net/ethernet/mellanox/mlx5/core/wq.c: In function 'mlx5_wq_cyc_wqe_dump':
include/linux/kern_levels.h:5:18: warning: format '%ld' expects argument of type 'long int', but argument 5 has type 'size_t' {aka 'unsigned int'} [-Wformat=]

Fixes: 130c7b46 ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events")
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The first batch of driver conversions missed a few cases where we can
use phy_do_ioctl too.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes coccicheck warning:

./drivers/net/ethernet/amd/declance.c:611:14-15:
	WARNING comparing pointer to 0

Replace "skb == 0" with "!skb".
Signed-off-by: NChen Zhou <chenzhou10@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes some unnecessary return value assignments,
some duplicated printing in the caller, refines the judgment
of 0 and uses le16_to_cpu to replace __le16_to_cpu.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All kmalloc-based functions print enough information on failures.
So this patch removes the log in hclge_get_dfx_reg() when returns
ENOMEM.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch deletes some unnecessary blank lines and spaces to clean up
code, and in hclgevf_set_vlan_filter() moves the comment to the front
of hclgevf_send_mbx_msg().
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When gets vector fails, hclge_put_vector() should print out
the vector instead of vector_id in the log and return the wrong
vector_id to its caller.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function snprintf() writes at most size bytes (including the
terminating null byte ('\0') to str. Now, We can guarantee that the
parameter of size is lager than the length of str to be formatting
including its terminating null byte. So it's unnecessary to minus 1
for the input parameter 'size'.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macro HCLGE_GET_DFX_REG_TYPE_CNT in hclge_dbg_get_dfx_bd_num()
and macro HCLGE_DFX_REG_BD_NUM in hclge_get_dfx_reg_bd_num()
have the same meaning, so just defines HCLGE_GET_DFX_REG_TYPE_CNT
in hclge_main.h.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

reset_type means what kind of reset the driver is handling now,
so after initializing or reset, the reset_type of VF should be
set to HNAE3_NONE_RESET, otherwise, this unknown default value
may be a little misleading when the device is running.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HNS3 driver allocates pages for DMA with dev_alloc_pages(), which
calls alloc_pages_node() with the __GFP_MEMALLOC flag. So, in case
of OOM condition, HNS3 can get pages with pfmemalloc flag set.

So do not reuse the pages with pfmemalloc flag set because those
pages are reserved for special cases, such as low memory case.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error log printed by netdev_err() in the hns3_clean_tx_ring()
may spam the kernel log.

This patch uses hns3_rl_err() to ratelimit the error log in the
hns3_clean_tx_ring().
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert suitable network drivers to use phy_do_ioctl.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We just added phy_do_ioctl, but it turned out that we need another
version of this function that doesn't check whether net_device is
running. So rename phy_do_ioctl to phy_do_ioctl_running.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

snprintf returns the number of bytes that would be written, which may be
greater than the the actual length to be written. Here use extra code to
handle this.

scnprintf returns the number of bytes that was actually written, just use
scnprintf to simplify the code.
Signed-off-by: NChen Zhou <chenzhou10@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The return value of snprintf may be greater than the size of
HNS3_DBG_READ_LEN, use scnprintf instead in hns3_dbg_cmd_read.
Signed-off-by: NChen Zhou <chenzhou10@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PUDE event is handled and the link is up, update the port SPAN
buffer size according to the current speed.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For SPAN egress mirroring buffer size, it is needed to use a different
formula for Spectrum and Spectrum-2. Move the buffer size computation to
ops and implement new formula for Spectrum-2.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid duplication of code that is doing buffsize update and put it into
a separate helper function.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>