To explain some code, this patch adds some comments, and modifies or
merges some comments to make them more neat.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NZhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 2 new selftests for VLAN Insertion offloading. Tests are for inner
and outer VLAN offloading.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds the logic to insert a given VLAN ID in a packet. This is offloaded
to HW and its descriptor based. For now, only XGMAC implements the
necessary callbacks.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for EEE in XGMAC cores by implementing the necessary
callbacks.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 4 new tests:
	- SA Insertion (register based)
	- SA Insertion (descriptor based)
	- SA Replacament (register based)
	- SA Replacement (descriptor based)
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the support for Source Address Insertion and Replacement in XGMAC
cores. Two methods are supported: Descriptor based and register based.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the ethtool interface to dump the register map in XGMAC cores.

Changes from v2:
	- Remove uneeded memset (Jakub)
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the support for Flexible PPS in XGMAC cores.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a counter that increments each time a packet with split header is
received.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the support for Split Header feature in the RX path and enable it in
XGMAC cores.

This does not impact neither beneficts bandwidth but it does reduces CPU
usage because without the feature all the entire packet is memcpy'ed,
while that with the feature only the header is.

With Split Header disabled 'perf stat -d' gives:
86870.624945 task-clock (msec)      #    0.429 CPUs utilized
     1073352 context-switches       #    0.012 M/sec
           1 cpu-migrations         #    0.000 K/sec
         213 page-faults            #    0.002 K/sec
327113872376 cycles                 #    3.766 GHz (62.53%)
 56618161216 instructions           #    0.17  insn per cycle (75.06%)
 10742205071 branches               #  123.658 M/sec (75.36%)
   584309242 branch-misses          #    5.44% of all branches (75.19%)
 17594787965 L1-dcache-loads        #  202.540 M/sec (74.88%)
  4003773131 L1-dcache-load-misses  #   22.76% of all L1-dcache hits (74.89%)
  1313301468 LLC-loads              #   15.118 M/sec (49.75%)
   355906510 LLC-load-misses        #   27.10% of all LL-cache hits (49.92%)

With Split Header enabled 'perf stat -d' gives:
49324.456539 task-clock (msec)     #    0.245 CPUs utilized
     2542387 context-switches      #    0.052 M/sec
           1 cpu-migrations        #    0.000 K/sec
         213 page-faults           #    0.004 K/sec
177092791469 cycles                #    3.590 GHz (62.30%)
 68555756017 instructions          #    0.39  insn per cycle (75.16%)
 12697019382 branches              #  257.418 M/sec (74.81%)
   442081897 branch-misses         #    3.48% of all branches (74.79%)
 20337958358 L1-dcache-loads       #  412.330 M/sec (75.46%)
  3820210140 L1-dcache-load-misses #   18.78% of all L1-dcache hits (75.35%)
  1257719198 LLC-loads             #   25.499 M/sec (49.73%)
   685543923 LLC-load-misses       #   54.51% of all LL-cache hits (49.86%)

Changes from v2:
	- Reword commit message (Jakub)
Changes from v1:
	- Add performance info (David)
	- Add misssing dma_sync_single_for_device()
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return the correct value when RX descriptor is not the last one.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to add Split Header support, stmmac_rx() needs to take into
account that packet may be split accross multiple descriptors.

Refactor the logic of this function in order to support this scenario.

Changes from v2:
	- Fixup if condition detection (Jakub)
	- Don't stop NAPI with unfinished packet (Jakub)
	- Use napi_alloc_skb() (Jakub)
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TX Timestamp in XGMAC comes from MAC instead of descriptors. Implement
this in a new callback.

Also, RX Timestamp in XGMAC must be cheked against corruption and we need
a barrier to make sure that descriptor fields are read correctly.

Changes from v2:
	- Rework return code check (Jakub)
Changes from v1:
	- Rework the get timestamp function (David)
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Have netdevsim register its trap groups and traps with devlink during
initialization and periodically report trapped packets to devlink core.

Since netdevsim is not a real device, the trapped packets are emulated
using a workqueue that periodically reports a UDP packet with a random
5-tuple from each active packet trap and from each running netdev.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that all users have been removed we can remove genphy_config_init.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy_config_init does is removing features that are set as
supported but can't be auto-detected. Basically it duplicates the
code in genphy_read_abilities. Therefore remove such calls from
all PHY drivers.

v2:
- remove call also from new adin PHY driver
v3:
- pass NULL as config_init function pointer for dp83848
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow encapsulated packets sent to tunnels layered over ipvlan to use
offloads rather than forcing SW fallbacks.

Since commit f21e5077 ("macvlan: add offload features for
encapsulation"), macvlan has set dev->hw_enc_features to include
everything in dev->features; do likewise in ipvlan.
Signed-off-by: NBill Sommerfeld <wsommerfeld@google.com>
Acked-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6xxx_port_setup_mac checks if the requested MAC settings are
different from the current ones, and if not, does nothing (since chaning
them requires putting the link down).

In this check it only looks if the triplet [link, speed, duplex] is
being changed.

This patch adds support to also check if the mode parameter (of type
phy_interface_t) is requested to be changed. The current mode is
computed by the ->port_link_state() method, and if it is different from
PHY_INTERFACE_MODE_NA, we check for equality with the requested mode.

In the implementations of the mv88e6250_port_link_state() method we set
the current mode to PHY_INTERFACE_MODE_NA - so the code does not check
for mode change on 6250.

In the mv88e6352_port_link_state() method, we use the cached cmode of
the port to determine the mode as phy_interface_t (and if it is not
enough, eg. for RGMII, we also look at the port control register for
RX/TX timings).
Signed-off-by: NMarek Behún <marek.behun@nic.cz>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change implements retrieving all the error counters from the PHY.

The counters require that the RxErrCnt register (0x0014) be read first,
after which copies of the counters are latched into the registers. This
ensures that all registers read after RxErrCnt are synchronized at the
moment that they are read.

The counter values need to be accumulated by the driver, as each time that
RxErrCnt is read, the values that are latched are the ones that have
incremented from the last read.
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Down-speed auto-negotiation may not always be enabled, in which case the
PHY won't down-shift to 100 or 10 during auto-negotiation.

This change enables downshift and configures the number of retries to
default 4 (which is also in the datasheet

The downshift control mechanism can also be controlled via the phy-tunable
interface (ETHTOOL_PHY_DOWNSHIFT control).

The change has been adapted from the Aquantia PHY driver.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ADIN PHYs supports 4 types of reset:
1. The standard PHY reset via BMCR_RESET bit in MII_BMCR reg
2. Reset via GPIO
3. Reset via reg GeSftRst (0xff0c) & reload previous pin configs
4. Reset via reg GeSftRst (0xff0c) & request new pin configs

Resets 2, 3 & 4 are almost identical, with the exception that the crystal
oscillator is available during reset for 2.

This change implements subsystem software reset via the GeSftRst and
reloading the previous pin configuration (so reset number 3).
This will also reset the PHY core regs (similar to reset 1).

Since writing bit 1 to reg GeSftRst is self-clearing, the only thing that
can be done, is to write to that register, wait a specific amount of time
(10 milliseconds should be enough) and try to read back and check if there
are no errors on read. A busy-wait-read won't work well, and may sometimes
work or not work.

In case phylib is configured to also do a reset via GPIO, the ADIN PHY may
be reset twice when the PHY device registers, but that isn't a problem,
since it's being done on boot (or PHY device register).
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ADIN1200 & ADIN1300 PHYs support EEE by using standard Clause 45 access
to access MMD registers for EEE.

The EEE register addresses (when using Clause 22) are available at
different addresses (than Clause 45), and since accessing these regs (via
Clause 22) needs a special mechanism, a translation table is required to
convert these addresses.

For Clause 45, this is not needed since the driver will likely never use
this access mode.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ADIN PHYs support automatic MDI/MDIX negotiation. By default this is
disabled, so this is enabled at `config_init`.

This is controlled via the PHY Control 1 register.
The supported modes are:
  1. Manual MDI
  2. Manual MDIX
  3. Auto MDIX - prefer MDIX
  4. Auto MDIX - prefer MDI

The phydev mdix & mdix_ctrl fields include modes 3 & 4 into a single
auto-mode. So, the default mode this driver enables is 4 when Auto-MDI mode
is used.

When detecting MDI/MDIX mode, a combination of the PHY Control 1 register
and PHY Status 1 register is used to determine the correct MDI/MDIX mode.

If Auto-MDI mode is not set, then the manual MDI/MDIX mode is returned.
If Auto-MDI mode is set, then MDIX mode is returned differs from the
preferred MDI/MDIX mode.
This covers all cases where:
  1. MDI preferred  & Pair01Swapped   == MDIX
  2. MDIX preferred & Pair01Swapped   == MDI
  3. MDI preferred  & ! Pair01Swapped == MDIX
  4. MDIX preferred & ! Pair01Swapped == MDI

The preferred MDI/MDIX mode is not configured via SW, but can be configured
via HW pins. Note that the `Pair01Swapped` is the Green-Yellow physical
pairs.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FIFO depth can be configured for the RMII mode. This change adds
support for doing this via device-tree (or ACPI).
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The internal delays for the RGMII are configurable for both RX & TX. This
change adds support for configuring them via device-tree (or ACPI).
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ADIN1300 chip supports RGMII, RMII & MII modes. Default (if
unconfigured) is RGMII.
This change adds support for configuring these modes via the device
registers.

For RGMII with internal delays (modes RGMII_ID,RGMII_TXID, RGMII_RXID),
the default delay is 2 ns. This can be configurable and will be done in
a subsequent change.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both ADIN1200 & ADIN1300 support Clause 45 access for some registers.
The Extended Management Interface (EMI) registers are accessible via both
Clause 45 (at register MDIO_MMD_VEND1) and using Clause 22.

The Clause 22 access for MMD regs differs from the standard one defined by
802.3. The ADIN PHYs  use registers ExtRegPtr (0x0010) and ExtRegData
(0x0011) to access Clause 45 & EMI registers.

The indirect access is done via the following mechanism (for both R/W):
1. Write the address of the register in the ExtRegPtr
2. Read/write the value of the register via reg ExtRegData

This mechanism is needed to manage configuration of chip settings and to
access EEE registers via Clause 22.

Since Clause 45 access will likely never be used, it is not implemented via
this hook.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change hooks link-status-change interrupts to phylib.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The chip supports standard suspend/resume via BMCR reg.
Hook these functions into the `adin` driver.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change adds support for Analog Devices Industrial Ethernet PHYs.
Particularly the PHYs this driver adds support for:
 * ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY
 * ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit
   Ethernet PHY

The 2 chips are register compatible with one another. The main difference
being that ADIN1200 doesn't operate in gigabit mode.

The chips can be operated by the Generic PHY driver as well via the
standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the
kernel as well. This assumes that configuration of the PHY has been done
completely in HW, according to spec.

Configuration can also be done via registers, which will be supported by
this driver.

Datasheets:
  https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1300.pdf
  https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1200.pdfReviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for PTP Hardware Clock (PHC) to the Ocelot
switch for both PTP 1-step and 2-step modes.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In struct frame_info, the cpuq member is never used. This cosmetic patch
removes it from the structure, and from the parsing of the frame header
as it's only set but never used.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This cosmetic patch improves the frame header parsing readability by
introducing a new macro to access and mask its fields.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for using the PTP register range, and adds a
description of its registers. This bank is used when configuring PTP.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds driver interface for reading the config attributes from user
provided buffer, and updates these values on nvm config flash partition.

This is basically an expansion of our existing ethtool -f implementation.
The management FW has exposed an additional method of configuring some of
the nvram options, and this makes use of that. This implementation will
come into use when newer FW files which contain configuration directives
employing this API will be provided to ethtool -f.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds API for configuring the NVM config attributes using
Management FW (MFW) interfaces.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement dummy region of size 32K and allow user to create snapshots
or random data using debugfs file trigger.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sync EEE init for RTL8168h with vendor driver and add two writes to
vendor-specific registers.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the Realtek PHY driver maps the vendor-specific EEE registers
to the standard MMD registers, we can remove all special handling and
use the generic functions phy_ethtool_get/set_eee.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>